[PATCH v9 12/26] powerpc/powernv/ioda1: M64 support on P7IOC

Gavin Shan gwshan at linux.vnet.ibm.com
Wed May 4 16:48:53 AEST 2016


On Wed, May 04, 2016 at 03:17:51PM +1000, Alistair Popple wrote:
>On Tue, 3 May 2016 15:41:31 Gavin Shan wrote:
>> This enables M64 window on P7IOC, which has been enabled on PHB3.
>
>Have we tested that this works with an adaptor? This looks to be enabling 
>support for something that didn't previously work (64-bit BARs on P7IOC)?
>

The M64 isn't supported on P7IOC before, meaning the PCI device's M64
BAR is covered by PHB's M32 window. With the patch applied, the PCI
device's M64 BAR is covered by PHB's M64 window as below log I got
from vpl4. The kernel including the series of patches boots successfully
on vpl4 and all looks normal.

[    0.246110] pci 0000:60:00.0: BAR 2: assigned [mem 0x3da810000000-0x3da810ffffff 64bit pref]
[    0.246218] pci 0000:60:00.0: BAR 0: assigned [mem 0x3da081000000-0x3da08103ffff 64bit]
[    0.246306] pci 0000:60:00.0: BAR 6: assigned [mem 0x3da081040000-0x3da08105ffff pref]
[    0.246392] pci 0000:60     : [PE# 001] Secondary bus 96 associated with PE#1
[    0.246484] pci 0000:60     : [PE# 001] DMA weight 15 (64), assigned (0) 1 DMA32 segments
[    0.246552] pci 0000:60     : [PE# 001]  Setting up 32-bit TCE table at 00000000..0fffffff

Thanks,
Gavin

>Regards,
>
>Alistair
>
>> Different from PHB3 where 16 M64 BARs are supported and each of
>> them can be owned by one particular PE# exclusively or divided
>> evenly to 256 segments, every P7IOC PHB has 16 M64 BARs and each
>> of them are divided to 8 segments. So every P7IOC PHB supports
>> 128 M64 segments in total. P7IOC has M64DT, which helps mapping
>> one particular M64 segment# to arbitrary PE#. PHB3 doesn't have
>> M64DT, indicating that one M64 segment can only be pinned to the
>> fixed PE#.
>> 
>> In order to unified M64 support M64 on P7IOC and PHB3, we just
>> provide 128 M64 segments on every P7IOC PHB and each of them is
>> pinned to the fixed PE# by bypassing the function of M64DT. In
>> turn, we just need different phb->init_m64() for P7IOC and PHB3
>> and maps M64 segment in pnv_ioda_reserve_m64_pe() for P7IOC, most
>> of the code are shared by them.
>> 
>> Signed-off-by: Gavin Shan <gwshan at linux.vnet.ibm.com>
>> ---
>>  arch/powerpc/platforms/powernv/pci-ioda.c | 89 
>+++++++++++++++++++++++++++++--
>>  1 file changed, 86 insertions(+), 3 deletions(-)
>> 
>> diff --git a/arch/powerpc/platforms/powernv/pci-ioda.c 
>b/arch/powerpc/platforms/powernv/pci-ioda.c
>> index 37f22b0..a1b74ec 100644
>> --- a/arch/powerpc/platforms/powernv/pci-ioda.c
>> +++ b/arch/powerpc/platforms/powernv/pci-ioda.c
>> @@ -48,6 +48,9 @@
>>  #include "powernv.h"
>>  #include "pci.h"
>>  
>> +#define PNV_IODA1_M64_NUM	16	/* Number of M64 BARs	*/
>> +#define PNV_IODA1_M64_SEGS	8	/* Segments per M64 BAR	*/
>> +
>>  /* 256M DMA window, 4K TCE pages, 8 bytes TCE */
>>  #define TCE32_TABLE_SIZE	((0x10000000 / 0x1000) * 8)
>>  
>> @@ -246,6 +249,64 @@ static void pnv_ioda_reserve_dev_m64_pe(struct pci_dev 
>*pdev,
>>  	}
>>  }
>>  
>> +static int pnv_ioda1_init_m64(struct pnv_phb *phb)
>> +{
>> +	struct resource *r;
>> +	int index;
>> +
>> +	/*
>> +	 * There are 16 M64 BARs, each of which has 8 segments. So
>> +	 * there are as many M64 segments as the maximum number of
>> +	 * PEs, which is 128.
>> +	 */
>> +	for (index = 0; index < PNV_IODA1_M64_NUM; index++) {
>> +		unsigned long base, segsz = phb->ioda.m64_segsize;
>> +		int64_t rc;
>> +
>> +		base = phb->ioda.m64_base +
>> +		       index * PNV_IODA1_M64_SEGS * segsz;
>> +		rc = opal_pci_set_phb_mem_window(phb->opal_id,
>> +				OPAL_M64_WINDOW_TYPE, index, base, 0,
>> +				PNV_IODA1_M64_SEGS * segsz);
>> +		if (rc != OPAL_SUCCESS) {
>> +			pr_warn("  Error %lld setting M64 PHB#%d-BAR#%d\n",
>> +				rc, phb->hose->global_number, index);
>> +			goto fail;
>> +		}
>> +
>> +		rc = opal_pci_phb_mmio_enable(phb->opal_id,
>> +				OPAL_M64_WINDOW_TYPE, index,
>> +				OPAL_ENABLE_M64_SPLIT);
>> +		if (rc != OPAL_SUCCESS) {
>> +			pr_warn("  Error %lld enabling M64 PHB#%d-BAR#%d\n",
>> +				rc, phb->hose->global_number, index);
>> +			goto fail;
>> +		}
>> +	}
>> +
>> +	/*
>> +	 * Exclude the segment used by the reserved PE, which
>> +	 * is expected to be 0 or last supported PE#.
>> +	 */
>> +	r = &phb->hose->mem_resources[1];
>> +	if (phb->ioda.reserved_pe_idx == 0)
>> +		r->start += phb->ioda.m64_segsize;
>> +	else if (phb->ioda.reserved_pe_idx == (phb->ioda.total_pe_num - 1))
>> +		r->end -= phb->ioda.m64_segsize;
>> +	else
>> +		pr_warn("  Cannot cut M64 segment for reserved PE#%d\n",
>> +			phb->ioda.reserved_pe_idx);
>> +
>> +	return 0;
>> +
>> +fail:
>> +	for ( ; index >= 0; index--)
>> +		opal_pci_phb_mmio_enable(phb->opal_id,
>> +			OPAL_M64_WINDOW_TYPE, index, OPAL_DISABLE_M64);
>> +
>> +	return -EIO;
>> +}
>> +
>>  static void pnv_ioda_reserve_m64_pe(struct pci_bus *bus,
>>  				    unsigned long *pe_bitmap,
>>  				    bool all)
>> @@ -315,6 +376,26 @@ static unsigned int pnv_ioda_pick_m64_pe(struct pci_bus 
>*bus, bool all)
>>  			pe->master = master_pe;
>>  			list_add_tail(&pe->list, &master_pe->slaves);
>>  		}
>> +
>> +		/*
>> +		 * P7IOC supports M64DT, which helps mapping M64 segment
>> +		 * to one particular PE#. However, PHB3 has fixed mapping
>> +		 * between M64 segment and PE#. In order to have same logic
>> +		 * for P7IOC and PHB3, we enforce fixed mapping between M64
>> +		 * segment and PE# on P7IOC.
>> +		 */
>> +		if (phb->type == PNV_PHB_IODA1) {
>> +			int64_t rc;
>> +
>> +			rc = opal_pci_map_pe_mmio_window(phb->opal_id,
>> +					pe->pe_number, OPAL_M64_WINDOW_TYPE,
>> +					pe->pe_number / PNV_IODA1_M64_SEGS,
>> +					pe->pe_number % PNV_IODA1_M64_SEGS);
>> +			if (rc != OPAL_SUCCESS)
>> +				pr_warn("%s: Error %lld mapping M64 for 
>PHB#%d-PE#%d\n",
>> +					__func__, rc, phb->hose-
>>global_number,
>> +					pe->pe_number);
>> +		}
>>  	}
>>  
>>  	kfree(pe_alloc);
>> @@ -329,8 +410,7 @@ static void __init pnv_ioda_parse_m64_window(struct 
>pnv_phb *phb)
>>  	const u32 *r;
>>  	u64 pci_addr;
>>  
>> -	/* FIXME: Support M64 for P7IOC */
>> -	if (phb->type != PNV_PHB_IODA2) {
>> +	if (phb->type != PNV_PHB_IODA1 && phb->type != PNV_PHB_IODA2) {
>>  		pr_info("  Not support M64 window\n");
>>  		return;
>>  	}
>> @@ -364,7 +444,10 @@ static void __init pnv_ioda_parse_m64_window(struct 
>pnv_phb *phb)
>>  
>>  	/* Use last M64 BAR to cover M64 window */
>>  	phb->ioda.m64_bar_idx = 15;
>> -	phb->init_m64 = pnv_ioda2_init_m64;
>> +	if (phb->type == PNV_PHB_IODA1)
>> +		phb->init_m64 = pnv_ioda1_init_m64;
>> +	else
>> +		phb->init_m64 = pnv_ioda2_init_m64;
>>  	phb->reserve_m64_pe = pnv_ioda_reserve_m64_pe;
>>  	phb->pick_m64_pe = pnv_ioda_pick_m64_pe;
>>  }
>> 
>



More information about the Linuxppc-dev mailing list