[PATCH v1 1/2] sata_dwc_460ex: move to generic DMA driver
Andy Shevchenko
andriy.shevchenko at linux.intel.com
Wed Mar 4 07:41:21 AEDT 2015
The SATA implementation based on two actually different devices, i.e. SATA and
DMA controllers.
For Synopsys DesignWare DMA we have already a generic implementation of the
driver. Thus, the patch converts the code to use DMAEngine framework and
dw_dmac driver.
In future it will be better to split the devices inside DTS as well like it's
done on other platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko at linux.intel.com>
---
drivers/ata/sata_dwc_460ex.c | 736 +++++++------------------------------------
1 file changed, 122 insertions(+), 614 deletions(-)
diff --git a/drivers/ata/sata_dwc_460ex.c b/drivers/ata/sata_dwc_460ex.c
index 7bc0c12..08cd63f 100644
--- a/drivers/ata/sata_dwc_460ex.c
+++ b/drivers/ata/sata_dwc_460ex.c
@@ -36,11 +36,16 @@
#include <linux/platform_device.h>
#include <linux/libata.h>
#include <linux/slab.h>
+
#include "libata.h"
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
+/* Supported DMA engine drivers */
+#include <linux/platform_data/dma-dw.h>
+#include <linux/dma/dw.h>
+
/* These two are defined in "libata.h" */
#undef DRV_NAME
#undef DRV_VERSION
@@ -60,153 +65,9 @@
#define NO_IRQ 0
#endif
-/* SATA DMA driver Globals */
-#define DMA_NUM_CHANS 1
-#define DMA_NUM_CHAN_REGS 8
-
-/* SATA DMA Register definitions */
#define AHB_DMA_BRST_DFLT 64 /* 16 data items burst length*/
-struct dmareg {
- u32 low; /* Low bits 0-31 */
- u32 high; /* High bits 32-63 */
-};
-
-/* DMA Per Channel registers */
-struct dma_chan_regs {
- struct dmareg sar; /* Source Address */
- struct dmareg dar; /* Destination address */
- struct dmareg llp; /* Linked List Pointer */
- struct dmareg ctl; /* Control */
- struct dmareg sstat; /* Source Status not implemented in core */
- struct dmareg dstat; /* Destination Status not implemented in core*/
- struct dmareg sstatar; /* Source Status Address not impl in core */
- struct dmareg dstatar; /* Destination Status Address not implemente */
- struct dmareg cfg; /* Config */
- struct dmareg sgr; /* Source Gather */
- struct dmareg dsr; /* Destination Scatter */
-};
-
-/* Generic Interrupt Registers */
-struct dma_interrupt_regs {
- struct dmareg tfr; /* Transfer Interrupt */
- struct dmareg block; /* Block Interrupt */
- struct dmareg srctran; /* Source Transfer Interrupt */
- struct dmareg dsttran; /* Dest Transfer Interrupt */
- struct dmareg error; /* Error */
-};
-
-struct ahb_dma_regs {
- struct dma_chan_regs chan_regs[DMA_NUM_CHAN_REGS];
- struct dma_interrupt_regs interrupt_raw; /* Raw Interrupt */
- struct dma_interrupt_regs interrupt_status; /* Interrupt Status */
- struct dma_interrupt_regs interrupt_mask; /* Interrupt Mask */
- struct dma_interrupt_regs interrupt_clear; /* Interrupt Clear */
- struct dmareg statusInt; /* Interrupt combined*/
- struct dmareg rq_srcreg; /* Src Trans Req */
- struct dmareg rq_dstreg; /* Dst Trans Req */
- struct dmareg rq_sgl_srcreg; /* Sngl Src Trans Req*/
- struct dmareg rq_sgl_dstreg; /* Sngl Dst Trans Req*/
- struct dmareg rq_lst_srcreg; /* Last Src Trans Req*/
- struct dmareg rq_lst_dstreg; /* Last Dst Trans Req*/
- struct dmareg dma_cfg; /* DMA Config */
- struct dmareg dma_chan_en; /* DMA Channel Enable*/
- struct dmareg dma_id; /* DMA ID */
- struct dmareg dma_test; /* DMA Test */
- struct dmareg res1; /* reserved */
- struct dmareg res2; /* reserved */
- /*
- * DMA Comp Params
- * Param 6 = dma_param[0], Param 5 = dma_param[1],
- * Param 4 = dma_param[2] ...
- */
- struct dmareg dma_params[6];
-};
-
-/* Data structure for linked list item */
-struct lli {
- u32 sar; /* Source Address */
- u32 dar; /* Destination address */
- u32 llp; /* Linked List Pointer */
- struct dmareg ctl; /* Control */
- struct dmareg dstat; /* Destination Status */
-};
-
-enum {
- SATA_DWC_DMAC_LLI_SZ = (sizeof(struct lli)),
- SATA_DWC_DMAC_LLI_NUM = 256,
- SATA_DWC_DMAC_LLI_TBL_SZ = (SATA_DWC_DMAC_LLI_SZ * \
- SATA_DWC_DMAC_LLI_NUM),
- SATA_DWC_DMAC_TWIDTH_BYTES = 4,
- SATA_DWC_DMAC_CTRL_TSIZE_MAX = (0x00000800 * \
- SATA_DWC_DMAC_TWIDTH_BYTES),
-};
-
-/* DMA Register Operation Bits */
enum {
- DMA_EN = 0x00000001, /* Enable AHB DMA */
- DMA_CTL_LLP_SRCEN = 0x10000000, /* Blk chain enable Src */
- DMA_CTL_LLP_DSTEN = 0x08000000, /* Blk chain enable Dst */
-};
-
-#define DMA_CTL_BLK_TS(size) ((size) & 0x000000FFF) /* Blk Transfer size */
-#define DMA_CHANNEL(ch) (0x00000001 << (ch)) /* Select channel */
- /* Enable channel */
-#define DMA_ENABLE_CHAN(ch) ((0x00000001 << (ch)) | \
- ((0x000000001 << (ch)) << 8))
- /* Disable channel */
-#define DMA_DISABLE_CHAN(ch) (0x00000000 | ((0x000000001 << (ch)) << 8))
- /* Transfer Type & Flow Controller */
-#define DMA_CTL_TTFC(type) (((type) & 0x7) << 20)
-#define DMA_CTL_SMS(num) (((num) & 0x3) << 25) /* Src Master Select */
-#define DMA_CTL_DMS(num) (((num) & 0x3) << 23)/* Dst Master Select */
- /* Src Burst Transaction Length */
-#define DMA_CTL_SRC_MSIZE(size) (((size) & 0x7) << 14)
- /* Dst Burst Transaction Length */
-#define DMA_CTL_DST_MSIZE(size) (((size) & 0x7) << 11)
- /* Source Transfer Width */
-#define DMA_CTL_SRC_TRWID(size) (((size) & 0x7) << 4)
- /* Destination Transfer Width */
-#define DMA_CTL_DST_TRWID(size) (((size) & 0x7) << 1)
-
-/* Assign HW handshaking interface (x) to destination / source peripheral */
-#define DMA_CFG_HW_HS_DEST(int_num) (((int_num) & 0xF) << 11)
-#define DMA_CFG_HW_HS_SRC(int_num) (((int_num) & 0xF) << 7)
-#define DMA_CFG_HW_CH_PRIOR(int_num) (((int_num) & 0xF) << 5)
-#define DMA_LLP_LMS(addr, master) (((addr) & 0xfffffffc) | (master))
-
-/*
- * This define is used to set block chaining disabled in the control low
- * register. It is already in little endian format so it can be &'d dirctly.
- * It is essentially: cpu_to_le32(~(DMA_CTL_LLP_SRCEN | DMA_CTL_LLP_DSTEN))
- */
-enum {
- DMA_CTL_LLP_DISABLE_LE32 = 0xffffffe7,
- DMA_CTL_TTFC_P2M_DMAC = 0x00000002, /* Per to mem, DMAC cntr */
- DMA_CTL_TTFC_M2P_PER = 0x00000003, /* Mem to per, peripheral cntr */
- DMA_CTL_SINC_INC = 0x00000000, /* Source Address Increment */
- DMA_CTL_SINC_DEC = 0x00000200,
- DMA_CTL_SINC_NOCHANGE = 0x00000400,
- DMA_CTL_DINC_INC = 0x00000000, /* Destination Address Increment */
- DMA_CTL_DINC_DEC = 0x00000080,
- DMA_CTL_DINC_NOCHANGE = 0x00000100,
- DMA_CTL_INT_EN = 0x00000001, /* Interrupt Enable */
-
-/* Channel Configuration Register high bits */
- DMA_CFG_FCMOD_REQ = 0x00000001, /* Flow Control - request based */
- DMA_CFG_PROTCTL = (0x00000003 << 2),/* Protection Control */
-
-/* Channel Configuration Register low bits */
- DMA_CFG_RELD_DST = 0x80000000, /* Reload Dest / Src Addr */
- DMA_CFG_RELD_SRC = 0x40000000,
- DMA_CFG_HS_SELSRC = 0x00000800, /* Software handshake Src/ Dest */
- DMA_CFG_HS_SELDST = 0x00000400,
- DMA_CFG_FIFOEMPTY = (0x00000001 << 9), /* FIFO Empty bit */
-
-/* Channel Linked List Pointer Register */
- DMA_LLP_AHBMASTER1 = 0, /* List Master Select */
- DMA_LLP_AHBMASTER2 = 1,
-
SATA_DWC_MAX_PORTS = 1,
SATA_DWC_SCR_OFFSET = 0x24,
@@ -287,7 +148,7 @@ struct sata_dwc_device {
struct ata_host *host;
u8 __iomem *reg_base;
struct sata_dwc_regs *sata_dwc_regs; /* DW Synopsys SATA specific */
- int irq_dma;
+ struct dw_dma_chip *dma;
};
#define SATA_DWC_QCMD_MAX 32
@@ -295,10 +156,13 @@ struct sata_dwc_device {
struct sata_dwc_device_port {
struct sata_dwc_device *hsdev;
int cmd_issued[SATA_DWC_QCMD_MAX];
- struct lli *llit[SATA_DWC_QCMD_MAX]; /* DMA LLI table */
- dma_addr_t llit_dma[SATA_DWC_QCMD_MAX];
- u32 dma_chan[SATA_DWC_QCMD_MAX];
int dma_pending[SATA_DWC_QCMD_MAX];
+
+ /* DMA info */
+ struct dw_dma_slave *dws;
+ struct dma_chan *chan;
+ struct dma_async_tx_descriptor *desc[SATA_DWC_QCMD_MAX];
+ u32 dma_interrupt_count;
};
/*
@@ -330,14 +194,18 @@ struct sata_dwc_host_priv {
void __iomem *scr_addr_sstatus;
u32 sata_dwc_sactive_issued ;
u32 sata_dwc_sactive_queued ;
- u32 dma_interrupt_count;
- struct ahb_dma_regs *sata_dma_regs;
struct device *dwc_dev;
- int dma_channel;
};
static struct sata_dwc_host_priv host_pvt;
+static struct dw_dma_slave sata_dwc_dma_dws = {
+ .src_id = 0,
+ .dst_id = 0,
+ .src_master = 0,
+ .dst_master = 1,
+};
+
/*
* Prototypes
*/
@@ -347,12 +215,6 @@ static int sata_dwc_qc_complete(struct ata_port *ap, struct ata_queued_cmd *qc,
static void sata_dwc_dma_xfer_complete(struct ata_port *ap, u32 check_status);
static void sata_dwc_port_stop(struct ata_port *ap);
static void sata_dwc_clear_dmacr(struct sata_dwc_device_port *hsdevp, u8 tag);
-static int dma_dwc_init(struct sata_dwc_device *hsdev, int irq);
-static void dma_dwc_exit(struct sata_dwc_device *hsdev);
-static int dma_dwc_xfer_setup(struct scatterlist *sg, int num_elems,
- struct lli *lli, dma_addr_t dma_lli,
- void __iomem *addr, int dir);
-static void dma_dwc_xfer_start(int dma_ch);
static const char *get_prot_descript(u8 protocol)
{
@@ -405,76 +267,8 @@ static void sata_dwc_tf_dump(struct ata_taskfile *tf)
tf->hob_lbah);
}
-/*
- * Function: get_burst_length_encode
- * arguments: datalength: length in bytes of data
- * returns value to be programmed in register corresponding to data length
- * This value is effectively the log(base 2) of the length
- */
-static int get_burst_length_encode(int datalength)
-{
- int items = datalength >> 2; /* div by 4 to get lword count */
-
- if (items >= 64)
- return 5;
-
- if (items >= 32)
- return 4;
-
- if (items >= 16)
- return 3;
-
- if (items >= 8)
- return 2;
-
- if (items >= 4)
- return 1;
-
- return 0;
-}
-
-static void clear_chan_interrupts(int c)
+static void dma_dwc_xfer_done(void *hsdev_instance)
{
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.tfr.low),
- DMA_CHANNEL(c));
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.block.low),
- DMA_CHANNEL(c));
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.srctran.low),
- DMA_CHANNEL(c));
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.dsttran.low),
- DMA_CHANNEL(c));
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear.error.low),
- DMA_CHANNEL(c));
-}
-
-/*
- * Function: dma_request_channel
- * arguments: None
- * returns channel number if available else -1
- * This function assigns the next available DMA channel from the list to the
- * requester
- */
-static int dma_request_channel(void)
-{
- /* Check if the channel is not currently in use */
- if (!(in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) &
- DMA_CHANNEL(host_pvt.dma_channel)))
- return host_pvt.dma_channel;
- dev_err(host_pvt.dwc_dev, "%s Channel %d is currently in use\n",
- __func__, host_pvt.dma_channel);
- return -1;
-}
-
-/*
- * Function: dma_dwc_interrupt
- * arguments: irq, dev_id, pt_regs
- * returns channel number if available else -1
- * Interrupt Handler for DW AHB SATA DMA
- */
-static irqreturn_t dma_dwc_interrupt(int irq, void *hsdev_instance)
-{
- int chan;
- u32 tfr_reg, err_reg;
unsigned long flags;
struct sata_dwc_device *hsdev = hsdev_instance;
struct ata_host *host = (struct ata_host *)hsdev->host;
@@ -488,341 +282,65 @@ static irqreturn_t dma_dwc_interrupt(int irq, void *hsdev_instance)
hsdevp = HSDEVP_FROM_AP(ap);
tag = ap->link.active_tag;
- tfr_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.tfr\
- .low));
- err_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.error\
- .low));
-
- dev_dbg(ap->dev, "eot=0x%08x err=0x%08x pending=%d active port=%d\n",
- tfr_reg, err_reg, hsdevp->dma_pending[tag], port);
-
- chan = host_pvt.dma_channel;
- if (chan >= 0) {
- /* Check for end-of-transfer interrupt. */
- if (tfr_reg & DMA_CHANNEL(chan)) {
- /*
- * Each DMA command produces 2 interrupts. Only
- * complete the command after both interrupts have been
- * seen. (See sata_dwc_isr())
- */
- host_pvt.dma_interrupt_count++;
- sata_dwc_clear_dmacr(hsdevp, tag);
-
- if (hsdevp->dma_pending[tag] ==
- SATA_DWC_DMA_PENDING_NONE) {
- dev_err(ap->dev, "DMA not pending eot=0x%08x "
- "err=0x%08x tag=0x%02x pending=%d\n",
- tfr_reg, err_reg, tag,
- hsdevp->dma_pending[tag]);
- }
-
- if ((host_pvt.dma_interrupt_count % 2) == 0)
- sata_dwc_dma_xfer_complete(ap, 1);
-
- /* Clear the interrupt */
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear\
- .tfr.low),
- DMA_CHANNEL(chan));
- }
-
- /* Check for error interrupt. */
- if (err_reg & DMA_CHANNEL(chan)) {
- /* TODO Need error handler ! */
- dev_err(ap->dev, "error interrupt err_reg=0x%08x\n",
- err_reg);
-
- /* Clear the interrupt. */
- out_le32(&(host_pvt.sata_dma_regs->interrupt_clear\
- .error.low),
- DMA_CHANNEL(chan));
- }
- }
- spin_unlock_irqrestore(&host->lock, flags);
- return IRQ_HANDLED;
-}
-
-/*
- * Function: dma_request_interrupts
- * arguments: hsdev
- * returns status
- * This function registers ISR for a particular DMA channel interrupt
- */
-static int dma_request_interrupts(struct sata_dwc_device *hsdev, int irq)
-{
- int retval = 0;
- int chan = host_pvt.dma_channel;
-
- if (chan >= 0) {
- /* Unmask error interrupt */
- out_le32(&(host_pvt.sata_dma_regs)->interrupt_mask.error.low,
- DMA_ENABLE_CHAN(chan));
-
- /* Unmask end-of-transfer interrupt */
- out_le32(&(host_pvt.sata_dma_regs)->interrupt_mask.tfr.low,
- DMA_ENABLE_CHAN(chan));
- }
-
- retval = request_irq(irq, dma_dwc_interrupt, 0, "SATA DMA", hsdev);
- if (retval) {
- dev_err(host_pvt.dwc_dev, "%s: could not get IRQ %d\n",
- __func__, irq);
- return -ENODEV;
- }
-
- /* Mark this interrupt as requested */
- hsdev->irq_dma = irq;
- return 0;
-}
-
-/*
- * Function: map_sg_to_lli
- * The Synopsis driver has a comment proposing that better performance
- * is possible by only enabling interrupts on the last item in the linked list.
- * However, it seems that could be a problem if an error happened on one of the
- * first items. The transfer would halt, but no error interrupt would occur.
- * Currently this function sets interrupts enabled for each linked list item:
- * DMA_CTL_INT_EN.
- */
-static int map_sg_to_lli(struct scatterlist *sg, int num_elems,
- struct lli *lli, dma_addr_t dma_lli,
- void __iomem *dmadr_addr, int dir)
-{
- int i, idx = 0;
- int fis_len = 0;
- dma_addr_t next_llp;
- int bl;
- int sms_val, dms_val;
-
- sms_val = 0;
- dms_val = 1 + host_pvt.dma_channel;
- dev_dbg(host_pvt.dwc_dev,
- "%s: sg=%p nelem=%d lli=%p dma_lli=0x%pad dmadr=0x%p\n",
- __func__, sg, num_elems, lli, &dma_lli, dmadr_addr);
-
- bl = get_burst_length_encode(AHB_DMA_BRST_DFLT);
-
- for (i = 0; i < num_elems; i++, sg++) {
- u32 addr, offset;
- u32 sg_len, len;
-
- addr = (u32) sg_dma_address(sg);
- sg_len = sg_dma_len(sg);
-
- dev_dbg(host_pvt.dwc_dev, "%s: elem=%d sg_addr=0x%x sg_len"
- "=%d\n", __func__, i, addr, sg_len);
-
- while (sg_len) {
- if (idx >= SATA_DWC_DMAC_LLI_NUM) {
- /* The LLI table is not large enough. */
- dev_err(host_pvt.dwc_dev, "LLI table overrun "
- "(idx=%d)\n", idx);
- break;
- }
- len = (sg_len > SATA_DWC_DMAC_CTRL_TSIZE_MAX) ?
- SATA_DWC_DMAC_CTRL_TSIZE_MAX : sg_len;
-
- offset = addr & 0xffff;
- if ((offset + sg_len) > 0x10000)
- len = 0x10000 - offset;
-
- /*
- * Make sure a LLI block is not created that will span
- * 8K max FIS boundary. If the block spans such a FIS
- * boundary, there is a chance that a DMA burst will
- * cross that boundary -- this results in an error in
- * the host controller.
- */
- if (fis_len + len > 8192) {
- dev_dbg(host_pvt.dwc_dev, "SPLITTING: fis_len="
- "%d(0x%x) len=%d(0x%x)\n", fis_len,
- fis_len, len, len);
- len = 8192 - fis_len;
- fis_len = 0;
- } else {
- fis_len += len;
- }
- if (fis_len == 8192)
- fis_len = 0;
-
- /*
- * Set DMA addresses and lower half of control register
- * based on direction.
- */
- if (dir == DMA_FROM_DEVICE) {
- lli[idx].dar = cpu_to_le32(addr);
- lli[idx].sar = cpu_to_le32((u32)dmadr_addr);
-
- lli[idx].ctl.low = cpu_to_le32(
- DMA_CTL_TTFC(DMA_CTL_TTFC_P2M_DMAC) |
- DMA_CTL_SMS(sms_val) |
- DMA_CTL_DMS(dms_val) |
- DMA_CTL_SRC_MSIZE(bl) |
- DMA_CTL_DST_MSIZE(bl) |
- DMA_CTL_SINC_NOCHANGE |
- DMA_CTL_SRC_TRWID(2) |
- DMA_CTL_DST_TRWID(2) |
- DMA_CTL_INT_EN |
- DMA_CTL_LLP_SRCEN |
- DMA_CTL_LLP_DSTEN);
- } else { /* DMA_TO_DEVICE */
- lli[idx].sar = cpu_to_le32(addr);
- lli[idx].dar = cpu_to_le32((u32)dmadr_addr);
-
- lli[idx].ctl.low = cpu_to_le32(
- DMA_CTL_TTFC(DMA_CTL_TTFC_M2P_PER) |
- DMA_CTL_SMS(dms_val) |
- DMA_CTL_DMS(sms_val) |
- DMA_CTL_SRC_MSIZE(bl) |
- DMA_CTL_DST_MSIZE(bl) |
- DMA_CTL_DINC_NOCHANGE |
- DMA_CTL_SRC_TRWID(2) |
- DMA_CTL_DST_TRWID(2) |
- DMA_CTL_INT_EN |
- DMA_CTL_LLP_SRCEN |
- DMA_CTL_LLP_DSTEN);
- }
-
- dev_dbg(host_pvt.dwc_dev, "%s setting ctl.high len: "
- "0x%08x val: 0x%08x\n", __func__,
- len, DMA_CTL_BLK_TS(len / 4));
-
- /* Program the LLI CTL high register */
- lli[idx].ctl.high = cpu_to_le32(DMA_CTL_BLK_TS\
- (len / 4));
-
- /* Program the next pointer. The next pointer must be
- * the physical address, not the virtual address.
- */
- next_llp = (dma_lli + ((idx + 1) * sizeof(struct \
- lli)));
-
- /* The last 2 bits encode the list master select. */
- next_llp = DMA_LLP_LMS(next_llp, DMA_LLP_AHBMASTER2);
-
- lli[idx].llp = cpu_to_le32(next_llp);
- idx++;
- sg_len -= len;
- addr += len;
- }
- }
-
/*
- * The last next ptr has to be zero and the last control low register
- * has to have LLP_SRC_EN and LLP_DST_EN (linked list pointer source
- * and destination enable) set back to 0 (disabled.) This is what tells
- * the core that this is the last item in the linked list.
+ * Each DMA command produces 2 interrupts. Only
+ * complete the command after both interrupts have been
+ * seen. (See sata_dwc_isr())
*/
- if (idx) {
- lli[idx-1].llp = 0x00000000;
- lli[idx-1].ctl.low &= DMA_CTL_LLP_DISABLE_LE32;
+ hsdevp->dma_interrupt_count++;
+ sata_dwc_clear_dmacr(hsdevp, tag);
- /* Flush cache to memory */
- dma_cache_sync(NULL, lli, (sizeof(struct lli) * idx),
- DMA_BIDIRECTIONAL);
+ if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_NONE) {
+ dev_err(ap->dev, "DMA not pending tag=0x%02x pending=%d\n",
+ tag, hsdevp->dma_pending[tag]);
}
- return idx;
-}
+ if ((hsdevp->dma_interrupt_count % 2) == 0)
+ sata_dwc_dma_xfer_complete(ap, 1);
-/*
- * Function: dma_dwc_xfer_start
- * arguments: Channel number
- * Return : None
- * Enables the DMA channel
- */
-static void dma_dwc_xfer_start(int dma_ch)
-{
- /* Enable the DMA channel */
- out_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low),
- in_le32(&(host_pvt.sata_dma_regs->dma_chan_en.low)) |
- DMA_ENABLE_CHAN(dma_ch));
+ spin_unlock_irqrestore(&host->lock, flags);
}
-static int dma_dwc_xfer_setup(struct scatterlist *sg, int num_elems,
- struct lli *lli, dma_addr_t dma_lli,
- void __iomem *addr, int dir)
+static struct dma_async_tx_descriptor *dma_dwc_xfer_setup(struct ata_queued_cmd *qc)
{
- int dma_ch;
- int num_lli;
- /* Acquire DMA channel */
- dma_ch = dma_request_channel();
- if (dma_ch == -1) {
- dev_err(host_pvt.dwc_dev, "%s: dma channel unavailable\n",
- __func__);
- return -EAGAIN;
+ struct ata_port *ap = qc->ap;
+ struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
+ dma_addr_t addr = (dma_addr_t)&hsdev->sata_dwc_regs->dmadr;
+ struct dma_slave_config sconf;
+ struct dma_async_tx_descriptor *desc;
+
+ if (qc->dma_dir == DMA_DEV_TO_MEM) {
+ sconf.src_addr = addr;
+ sconf.device_fc = true;
+ } else { /* DMA_MEM_TO_DEV */
+ sconf.dst_addr = addr;
+ sconf.device_fc = false;
}
- /* Convert SG list to linked list of items (LLIs) for AHB DMA */
- num_lli = map_sg_to_lli(sg, num_elems, lli, dma_lli, addr, dir);
-
- dev_dbg(host_pvt.dwc_dev, "%s sg: 0x%p, count: %d lli: %p dma_lli:"
- " 0x%0xlx addr: %p lli count: %d\n", __func__, sg, num_elems,
- lli, (u32)dma_lli, addr, num_lli);
-
- clear_chan_interrupts(dma_ch);
-
- /* Program the CFG register. */
- out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.high),
- DMA_CFG_HW_HS_SRC(dma_ch) | DMA_CFG_HW_HS_DEST(dma_ch) |
- DMA_CFG_PROTCTL | DMA_CFG_FCMOD_REQ);
- out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].cfg.low),
- DMA_CFG_HW_CH_PRIOR(dma_ch));
-
- /* Program the address of the linked list */
- out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].llp.low),
- DMA_LLP_LMS(dma_lli, DMA_LLP_AHBMASTER2));
-
- /* Program the CTL register with src enable / dst enable */
- out_le32(&(host_pvt.sata_dma_regs->chan_regs[dma_ch].ctl.low),
- DMA_CTL_LLP_SRCEN | DMA_CTL_LLP_DSTEN);
- return dma_ch;
-}
-
-/*
- * Function: dma_dwc_exit
- * arguments: None
- * returns status
- * This function exits the SATA DMA driver
- */
-static void dma_dwc_exit(struct sata_dwc_device *hsdev)
-{
- dev_dbg(host_pvt.dwc_dev, "%s:\n", __func__);
- if (host_pvt.sata_dma_regs) {
- iounmap((void __iomem *)host_pvt.sata_dma_regs);
- host_pvt.sata_dma_regs = NULL;
- }
+ sconf.direction = qc->dma_dir;
+ sconf.src_maxburst = AHB_DMA_BRST_DFLT;
+ sconf.dst_maxburst = AHB_DMA_BRST_DFLT;
+ sconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ sconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- if (hsdev->irq_dma) {
- free_irq(hsdev->irq_dma, hsdev);
- hsdev->irq_dma = 0;
- }
-}
+ dmaengine_slave_config(hsdevp->chan, &sconf);
-/*
- * Function: dma_dwc_init
- * arguments: hsdev
- * returns status
- * This function initializes the SATA DMA driver
- */
-static int dma_dwc_init(struct sata_dwc_device *hsdev, int irq)
-{
- int err;
+ /* Convert SG list to linked list of items (LLIs) for AHB DMA */
+ desc = dmaengine_prep_slave_sg(hsdevp->chan, qc->sg, qc->n_elem,
+ qc->dma_dir,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- err = dma_request_interrupts(hsdev, irq);
- if (err) {
- dev_err(host_pvt.dwc_dev, "%s: dma_request_interrupts returns"
- " %d\n", __func__, err);
- return err;
- }
+ if (!desc)
+ return NULL;
- /* Enabe DMA */
- out_le32(&(host_pvt.sata_dma_regs->dma_cfg.low), DMA_EN);
+ desc->callback = dma_dwc_xfer_done;
+ desc->callback_param = hsdev;
- dev_notice(host_pvt.dwc_dev, "DMA initialized\n");
- dev_dbg(host_pvt.dwc_dev, "SATA DMA registers=0x%p\n", host_pvt.\
- sata_dma_regs);
+ dev_dbg(host_pvt.dwc_dev, "%s sg: 0x%p, count: %d addr: %pad\n",
+ __func__, qc->sg, qc->n_elem, &addr);
- return 0;
+ return desc;
}
static int sata_dwc_scr_read(struct ata_link *link, unsigned int scr, u32 *val)
@@ -892,21 +410,18 @@ static void sata_dwc_error_intr(struct ata_port *ap,
struct ata_queued_cmd *qc;
u32 serror;
u8 status, tag;
- u32 err_reg;
ata_ehi_clear_desc(ehi);
serror = core_scr_read(SCR_ERROR);
status = ap->ops->sff_check_status(ap);
- err_reg = in_le32(&(host_pvt.sata_dma_regs->interrupt_status.error.\
- low));
tag = ap->link.active_tag;
- dev_err(ap->dev, "%s SCR_ERROR=0x%08x intpr=0x%08x status=0x%08x "
- "dma_intp=%d pending=%d issued=%d dma_err_status=0x%08x\n",
- __func__, serror, intpr, status, host_pvt.dma_interrupt_count,
- hsdevp->dma_pending[tag], hsdevp->cmd_issued[tag], err_reg);
+ dev_err(ap->dev,
+ "%s SCR_ERROR=0x%08x intpr=0x%08x status=0x%08x dma_intp=%d pending=%d issued=%d",
+ __func__, serror, intpr, status, hsdevp->dma_interrupt_count,
+ hsdevp->dma_pending[tag], hsdevp->cmd_issued[tag]);
/* Clear error register and interrupt bit */
clear_serror();
@@ -1033,7 +548,7 @@ DRVSTILLBUSY:
* operation done interrupt. The command should be
* completed only after both interrupts are seen.
*/
- host_pvt.dma_interrupt_count++;
+ hsdevp->dma_interrupt_count++;
if (hsdevp->dma_pending[tag] == \
SATA_DWC_DMA_PENDING_NONE) {
dev_err(ap->dev,
@@ -1042,7 +557,7 @@ DRVSTILLBUSY:
hsdevp->dma_pending[tag]);
}
- if ((host_pvt.dma_interrupt_count % 2) == 0)
+ if ((hsdevp->dma_interrupt_count % 2) == 0)
sata_dwc_dma_xfer_complete(ap, 1);
} else if (ata_is_pio(qc->tf.protocol)) {
ata_sff_hsm_move(ap, qc, status, 0);
@@ -1116,12 +631,12 @@ DRVSTILLBUSY:
dev_dbg(ap->dev, "%s NCQ command, protocol: %s\n", __func__,
get_prot_descript(qc->tf.protocol));
if (ata_is_dma(qc->tf.protocol)) {
- host_pvt.dma_interrupt_count++;
+ hsdevp->dma_interrupt_count++;
if (hsdevp->dma_pending[tag] == \
SATA_DWC_DMA_PENDING_NONE)
dev_warn(ap->dev, "%s: DMA not pending?\n",
__func__);
- if ((host_pvt.dma_interrupt_count % 2) == 0)
+ if ((hsdevp->dma_interrupt_count % 2) == 0)
sata_dwc_dma_xfer_complete(ap, 1);
} else {
if (unlikely(sata_dwc_qc_complete(ap, qc, 1)))
@@ -1269,6 +784,18 @@ static void sata_dwc_enable_interrupts(struct sata_dwc_device *hsdev)
in_le32(&hsdev->sata_dwc_regs->errmr));
}
+static bool sata_dwc_dma_filter(struct dma_chan *chan, void *param)
+{
+ struct sata_dwc_device_port *hsdevp = param;
+ struct dw_dma_slave *dws = hsdevp->dws;
+
+ if (dws->dma_dev != chan->device->dev)
+ return false;
+
+ chan->private = dws;
+ return true;
+}
+
static void sata_dwc_setup_port(struct ata_ioports *port, unsigned long base)
{
port->cmd_addr = (void __iomem *)base + 0x00;
@@ -1303,6 +830,7 @@ static int sata_dwc_port_start(struct ata_port *ap)
struct sata_dwc_device *hsdev;
struct sata_dwc_device_port *hsdevp = NULL;
struct device *pdev;
+ dma_cap_mask_t mask;
int i;
hsdev = HSDEV_FROM_AP(ap);
@@ -1326,29 +854,27 @@ static int sata_dwc_port_start(struct ata_port *ap)
}
hsdevp->hsdev = hsdev;
+ hsdevp->dws = &sata_dwc_dma_dws;
+ hsdevp->dws->dma_dev = host_pvt.dwc_dev;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ /* Acquire DMA channel */
+ hsdevp->chan = dma_request_channel(mask, sata_dwc_dma_filter, hsdevp);
+ if (!hsdevp->chan) {
+ dev_err(host_pvt.dwc_dev, "%s: dma channel unavailable\n",
+ __func__);
+ err = -EAGAIN;
+ goto CLEANUP_ALLOC;
+ }
+
for (i = 0; i < SATA_DWC_QCMD_MAX; i++)
hsdevp->cmd_issued[i] = SATA_DWC_CMD_ISSUED_NOT;
ap->bmdma_prd = NULL; /* set these so libata doesn't use them */
ap->bmdma_prd_dma = 0;
- /*
- * DMA - Assign scatter gather LLI table. We can't use the libata
- * version since it's PRD is IDE PCI specific.
- */
- for (i = 0; i < SATA_DWC_QCMD_MAX; i++) {
- hsdevp->llit[i] = dma_alloc_coherent(pdev,
- SATA_DWC_DMAC_LLI_TBL_SZ,
- &(hsdevp->llit_dma[i]),
- GFP_ATOMIC);
- if (!hsdevp->llit[i]) {
- dev_err(ap->dev, "%s: dma_alloc_coherent failed\n",
- __func__);
- err = -ENOMEM;
- goto CLEANUP_ALLOC;
- }
- }
-
if (ap->port_no == 0) {
dev_dbg(ap->dev, "%s: clearing TXCHEN, RXCHEN in DMAC\n",
__func__);
@@ -1377,22 +903,14 @@ CLEANUP:
static void sata_dwc_port_stop(struct ata_port *ap)
{
- int i;
- struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
dev_dbg(ap->dev, "%s: ap->id = %d\n", __func__, ap->print_id);
- if (hsdevp && hsdev) {
- /* deallocate LLI table */
- for (i = 0; i < SATA_DWC_QCMD_MAX; i++) {
- dma_free_coherent(ap->host->dev,
- SATA_DWC_DMAC_LLI_TBL_SZ,
- hsdevp->llit[i], hsdevp->llit_dma[i]);
- }
+ dmaengine_terminate_all(hsdevp->chan);
+ dma_release_channel(hsdevp->chan);
- kfree(hsdevp);
- }
+ kfree(hsdevp);
ap->private_data = NULL;
}
@@ -1448,12 +966,12 @@ static void sata_dwc_bmdma_setup(struct ata_queued_cmd *qc)
static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag)
{
int start_dma;
- u32 reg, dma_chan;
+ u32 reg;
struct sata_dwc_device *hsdev = HSDEV_FROM_QC(qc);
struct ata_port *ap = qc->ap;
struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
+ struct dma_async_tx_descriptor *desc = hsdevp->desc[tag];
int dir = qc->dma_dir;
- dma_chan = hsdevp->dma_chan[tag];
if (hsdevp->cmd_issued[tag] != SATA_DWC_CMD_ISSUED_NOT) {
start_dma = 1;
@@ -1489,7 +1007,8 @@ static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag)
SATA_DWC_DMACR_RXCHEN);
/* Enable AHB DMA transfer on the specified channel */
- dma_dwc_xfer_start(dma_chan);
+ dmaengine_submit(desc);
+ dma_async_issue_pending(hsdevp->chan);
}
}
@@ -1515,26 +1034,21 @@ static void sata_dwc_bmdma_start(struct ata_queued_cmd *qc)
*/
static void sata_dwc_qc_prep_by_tag(struct ata_queued_cmd *qc, u8 tag)
{
- struct scatterlist *sg = qc->sg;
+ struct dma_async_tx_descriptor *desc;
struct ata_port *ap = qc->ap;
- int dma_chan;
- struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
dev_dbg(ap->dev, "%s: port=%d dma dir=%s n_elem=%d\n",
__func__, ap->port_no, get_dma_dir_descript(qc->dma_dir),
qc->n_elem);
- dma_chan = dma_dwc_xfer_setup(sg, qc->n_elem, hsdevp->llit[tag],
- hsdevp->llit_dma[tag],
- (void __iomem *)&hsdev->sata_dwc_regs->dmadr,
- qc->dma_dir);
- if (dma_chan < 0) {
- dev_err(ap->dev, "%s: dma_dwc_xfer_setup returns err %d\n",
- __func__, dma_chan);
+ desc = dma_dwc_xfer_setup(qc);
+ if (!desc) {
+ dev_err(ap->dev, "%s: dma_dwc_xfer_setup returns NULL\n",
+ __func__);
return;
}
- hsdevp->dma_chan[tag] = dma_chan;
+ hsdevp->desc[tag] = desc;
}
static unsigned int sata_dwc_qc_issue(struct ata_queued_cmd *qc)
@@ -1678,7 +1192,6 @@ static int sata_dwc_probe(struct platform_device *ofdev)
struct ata_port_info pi = sata_dwc_port_info[0];
const struct ata_port_info *ppi[] = { &pi, NULL };
struct device_node *np = ofdev->dev.of_node;
- u32 dma_chan;
/* Allocate DWC SATA device */
host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_DWC_MAX_PORTS);
@@ -1688,13 +1201,6 @@ static int sata_dwc_probe(struct platform_device *ofdev)
host->private_data = hsdev;
- if (of_property_read_u32(np, "dma-channel", &dma_chan)) {
- dev_warn(&ofdev->dev, "no dma-channel property set."
- " Use channel 0\n");
- dma_chan = 0;
- }
- host_pvt.dma_channel = dma_chan;
-
/* Ioremap SATA registers */
base = of_iomap(np, 0);
if (!base) {
@@ -1721,16 +1227,16 @@ static int sata_dwc_probe(struct platform_device *ofdev)
idr, ver[0], ver[1], ver[2]);
/* Get SATA DMA interrupt number */
- irq = irq_of_parse_and_map(np, 1);
- if (irq == NO_IRQ) {
+ hsdev->dma->irq = irq_of_parse_and_map(np, 1);
+ if (hsdev->dma->irq == NO_IRQ) {
dev_err(&ofdev->dev, "no SATA DMA irq\n");
err = -ENODEV;
goto error_iomap;
}
/* Get physical SATA DMA register base address */
- host_pvt.sata_dma_regs = (void *)of_iomap(np, 1);
- if (!(host_pvt.sata_dma_regs)) {
+ hsdev->dma->regs = of_iomap(np, 1);
+ if (!hsdev->dma->regs) {
dev_err(&ofdev->dev,
"ioremap failed for AHBDMA register address\n");
err = -ENODEV;
@@ -1740,8 +1246,10 @@ static int sata_dwc_probe(struct platform_device *ofdev)
/* Save dev for later use in dev_xxx() routines */
host_pvt.dwc_dev = &ofdev->dev;
+ hsdev->dma->dev = &ofdev->dev;
+
/* Initialize AHB DMAC */
- err = dma_dwc_init(hsdev, irq);
+ err = dw_dma_probe(hsdev->dma, NULL);
if (err)
goto error_dma_iomap;
@@ -1770,9 +1278,9 @@ static int sata_dwc_probe(struct platform_device *ofdev)
error_out:
/* Free SATA DMA resources */
- dma_dwc_exit(hsdev);
+ dw_dma_remove(hsdev->dma);
error_dma_iomap:
- iounmap((void __iomem *)host_pvt.sata_dma_regs);
+ iounmap(hsdev->dma->regs);
error_iomap:
iounmap(base);
return err;
@@ -1787,9 +1295,9 @@ static int sata_dwc_remove(struct platform_device *ofdev)
ata_host_detach(host);
/* Free SATA DMA resources */
- dma_dwc_exit(hsdev);
+ dw_dma_remove(hsdev->dma);
- iounmap((void __iomem *)host_pvt.sata_dma_regs);
+ iounmap(hsdev->dma->regs);
iounmap(hsdev->reg_base);
dev_dbg(&ofdev->dev, "done\n");
return 0;
--
2.1.4
More information about the Linuxppc-dev
mailing list