[RFC PATCH 4/8] clk: qoriq: Move chip-specific knowledge into driver
Scott Wood
scottwood at freescale.com
Fri Jun 19 12:49:14 AEST 2015
The device tree should describe the chips (or chip-like subblocks) in
the system, but it generally does not describe individual registers --
it should identify, rather than describe, a programming interface.
This has not been the case with the QorIQ clockgen nodes. The
knowledge of what each bit setting of CLKCnCSR means is encoded in
three places (binding, pll node, and mux node), and the last also needs
to know which options are valid on a particular chip. All three of
these locations are considered stable ABI, making it difficult to fix
mistakes (of which I have found several), much less refactor the
abstraction to be able to address problems, limitations, or new chips.
Under the current binding, a pll clock specifier of 2 means that the
PLL is divided by 4 -- and the driver implements this, unless there
happen to be four clock-output-names rather than 3, in which case it
interprets it as PLL divided by 3. This does not appear in the binding
documentation at all. That hack is now considered stable ABI.
The current device tree nodes contain errors, such as saying that
T1040 can set a core clock to PLL/4 when only PLL and PLL/2 are options.
The current binding also ignores some restrictions on clock selection,
such as p5020's requirement that if a core uses the "wrong" PLL, that
PLL must be clocked lower than the "correct" PLL and be at most 80% of
the rated CPU frequency.
Possibly because of the lack of the ability to express such nuance in
the binding, some valid options are omitted from the device trees, such
as the ability on p4080 to run cores 0-3 from PLL3 and cores 4-7 from
PLL1 (again, only if they are at most 80% of rated CPU frequency).
This omission, combined with excessive caution in the cpufreq driver
(addressed in a subsequent patch), means that currently on a 1500 MHz
p4080 with typical PLL configuration, cpufreq can lower the frequency
to 1200 MHz on half the CPUs and do nothing on the others. With this
patchset, all CPUs can be lowered to 1200 MHz on a rev2 p4080, and on a
rev3 p4080 half can be lowered to 750 MHz and the other half to 600
MHz.
The current binding only deals with CPU clocks. To describe FMan in
the device tree, we need to describe its clock. Some chips have
additional muxes that work like the CPU muxes, but are not described in
the device tree. Others require inspecting the Reset Control Word to
determine which PLL is used. Rather than continue to extend this mess,
replace it. Have the driver bind to the chip-specific clockgen
compatible, and keep the detailed description of quirky chip variations
in the driver, where it can be easily fixed, refactored, and extended.
Older device trees will continue to work. This patch does not remove
the code for handling the old nodes. A subsequent patch removes that
code, but still binds against those nodes and redirects clock lookups
to the clocks generated by the new code.
Signed-off-by: Scott Wood <scottwood at freescale.com>
---
.../devicetree/bindings/clock/qoriq-clock.txt | 57 +-
drivers/clk/clk-qoriq.c | 950 ++++++++++++++++++++-
2 files changed, 986 insertions(+), 21 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
index df4a259..c48a04d 100644
--- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt
+++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
@@ -18,9 +18,11 @@ Chassis Version Example Chips
1. Clock Block Binding
Required properties:
-- compatible: Should contain a specific clock block compatible string
- and a single chassis clock compatible string.
- Clock block strings include, but not limited to, one of the:
+- compatible: Should contain a chip-specific clock block compatible
+ string and (if applicable) may contain a chassis-version clock
+ compatible string.
+
+ Chip-specific strings are of the form "fsl,<chip>-clockgen", such as:
* "fsl,p2041-clockgen"
* "fsl,p3041-clockgen"
* "fsl,p4080-clockgen"
@@ -30,15 +32,14 @@ Required properties:
* "fsl,b4420-clockgen"
* "fsl,b4860-clockgen"
* "fsl,ls1021a-clockgen"
- Chassis clock strings include:
+ Chassis-version clock strings include:
* "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks
* "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks
- reg: Describes the address of the device's resources within the
address space defined by its parent bus, and resource zero
represents the clock register set
-- clock-frequency: Input system clock frequency
-Recommended properties:
+Optional properties:
- ranges: Allows valid translation between child's address space and
parent's. Must be present if the device has sub-nodes.
- #address-cells: Specifies the number of cells used to represent
@@ -47,8 +48,46 @@ Recommended properties:
- #size-cells: Specifies the number of cells used to represent
the size of an address. Must be present if the device has
sub-nodes and set to 1 if present
+- clock-frequency: Input system clock frequency (SYSCLK)
+- clocks: If clock-frequency is not specified, sysclk may be provided
+ as an input clock. Either clock-frequency or clocks must be
+ provided.
+
+2. Clock Provider
+
+The clockgen node should act as a clock provider, though in older device
+trees the children of the clockgen node are the clock providers.
+
+When the clockgen node is a clock provider, #clock-cells = <2>.
+The first cell of the clock specifier is the clock type, and the
+second cell is the clock index for the specified type.
+
+ Type# Name Index Cell
+ 0 sysclk must be 0
+ 1 cmux index (n in CLKCnCSR)
+ 2 hwaccel index (n in CLKCGnHWACSR)
+ 3 fman 0 for fm1, 1 for fm2
+ 4 platform pll 0=pll, 1=pll/2, 2=pll/3, 3=pll/4
+
+3. Example
+
+ clockgen: global-utilities at e1000 {
+ compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
+ clock-frequency = <133333333>;
+ reg = <0xe1000 0x1000>;
+ #clock-cells = <2>;
+ };
+
+ fman at 400000 {
+ ...
+ clocks = <&clockgen 3 0>;
+ ...
+ };
+}
+4. Legacy Child Nodes
-2. Clock Provider/Consumer Binding
+NOTE: These nodes are deprecated. Kernels should continue to support
+device trees with these nodes, but new device trees should not use them.
Most of the bindings are from the common clock binding[1].
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
@@ -82,7 +121,7 @@ Recommended properties:
- reg: Should be the offset and length of clock block base address.
The length should be 4.
-Example for clock block and clock provider:
+Legacy Example:
/ {
clockgen: global-utilities at e1000 {
compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
@@ -142,7 +181,7 @@ Example for clock block and clock provider:
};
};
-Example for clock consumer:
+Example for legacy clock consumer:
/ {
cpu0: PowerPC,e5500 at 0 {
diff --git a/drivers/clk/clk-qoriq.c b/drivers/clk/clk-qoriq.c
index cda90a9..b94dc2f 100644
--- a/drivers/clk/clk-qoriq.c
+++ b/drivers/clk/clk-qoriq.c
@@ -11,6 +11,7 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/clk-provider.h>
+#include <linux/fsl/guts.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
@@ -19,6 +20,749 @@
#include <linux/of.h>
#include <linux/slab.h>
+#define PLL_DIV1 0
+#define PLL_DIV2 1
+#define PLL_DIV3 2
+#define PLL_DIV4 3
+
+#define PLATFORM_PLL 0
+#define CGA_PLL1 1
+#define CGA_PLL2 2
+#define CGA_PLL3 3
+#define CGA_PLL4 4 /* only on clockgen-1.0, which lacks CGB */
+#define CGB_PLL1 4
+#define CGB_PLL2 5
+
+struct clockgen_pll_div {
+ struct clk *clk;
+ char name[32];
+};
+
+struct clockgen_pll {
+ struct clockgen_pll_div div[4];
+};
+
+#define CLKSEL_VALID 1
+#define CLKSEL_80PCT 2 /* Only allowed if PLL <= 80% of max cpu freq */
+
+struct clockgen_sourceinfo {
+ u32 flags; /* CLKSEL_xxx */
+ int pll; /* CGx_PLLn */
+ int div; /* PLL_DIVn */
+};
+
+#define NUM_MUX_PARENTS 16
+
+struct clockgen_muxinfo {
+ struct clockgen_sourceinfo clksel[NUM_MUX_PARENTS];
+};
+
+#define NUM_HWACCEL 5
+#define NUM_CMUX 8
+
+struct clockgen;
+
+/*
+ * cmux freq must be >= platform pll.
+ * If not set, cmux freq must be >= platform pll/2
+ */
+#define CG_CMUX_GE_PLAT 1
+#define CG_PLL_8BIT 2 /* PLLCnGSR[CFG] is 8 bits, not 6 */
+
+struct clockgen_chipinfo {
+ const char *compat, *guts_compat;
+ const struct clockgen_muxinfo *cmux_groups[2];
+ const struct clockgen_muxinfo *hwaccel[NUM_HWACCEL];
+ void (*init_periph)(struct clockgen *cg);
+ int cmux_to_group[NUM_CMUX]; /* -1 terminates if fewer than NUM_CMUX */
+ u32 pll_mask; /* 1 << n bit set if PLL n is valid */
+ u32 flags; /* CG_xxx */
+};
+
+struct clockgen {
+ struct device_node *node;
+ void __iomem *regs;
+ struct clockgen_chipinfo info; /* mutable copy */
+ struct clk *sysclk;
+ struct clockgen_pll pll[6];
+ struct clk *cmux[NUM_CMUX];
+ struct clk *hwaccel[NUM_HWACCEL];
+ struct clk *fman[2];
+ struct ccsr_guts __iomem *guts;
+};
+
+static struct clockgen clockgen;
+
+static const struct clockgen_muxinfo p2041_cmux_grp1 = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ }
+};
+
+static const struct clockgen_muxinfo p2041_cmux_grp2 = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [4] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [5] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ }
+};
+
+static const struct clockgen_muxinfo p5020_cmux_grp1 = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL2, PLL_DIV1 },
+ }
+};
+
+static const struct clockgen_muxinfo p5020_cmux_grp2 = {
+ {
+ [0] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL1, PLL_DIV1 },
+ [4] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ [5] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ }
+};
+
+static const struct clockgen_muxinfo p5040_cmux_grp1 = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL2, PLL_DIV1 },
+ [5] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL2, PLL_DIV2 },
+ }
+};
+
+static const struct clockgen_muxinfo p5040_cmux_grp2 = {
+ {
+ [0] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ [5] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ }
+};
+
+static const struct clockgen_muxinfo p4080_cmux_grp1 = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ [5] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ [8] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL3, PLL_DIV1 },
+ }
+};
+
+static const struct clockgen_muxinfo p4080_cmux_grp2 = {
+ {
+ [0] = { CLKSEL_VALID | CLKSEL_80PCT, CGA_PLL1, PLL_DIV1 },
+ [8] = { CLKSEL_VALID, CGA_PLL3, PLL_DIV1 },
+ [9] = { CLKSEL_VALID, CGA_PLL3, PLL_DIV2 },
+ [12] = { CLKSEL_VALID, CGA_PLL4, PLL_DIV1 },
+ [13] = { CLKSEL_VALID, CGA_PLL4, PLL_DIV2 },
+ }
+};
+
+static const struct clockgen_muxinfo t1023_cmux = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ }
+};
+
+static const struct clockgen_muxinfo t1040_cmux = {
+ {
+ [0] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ [1] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ [4] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ [5] = { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ }
+};
+
+
+static const struct clockgen_muxinfo clockgen2_cmux_cga = {
+ {
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV4 },
+ {},
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV4 },
+ {},
+ { CLKSEL_VALID, CGA_PLL3, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL3, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL3, PLL_DIV4 },
+ },
+};
+
+static const struct clockgen_muxinfo clockgen2_cmux_cga12 = {
+ {
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV4 },
+ {},
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV4 },
+ },
+};
+
+static const struct clockgen_muxinfo clockgen2_cmux_cgb = {
+ {
+ { CLKSEL_VALID, CGB_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGB_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGB_PLL1, PLL_DIV4 },
+ {},
+ { CLKSEL_VALID, CGB_PLL2, PLL_DIV1 },
+ { CLKSEL_VALID, CGB_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGB_PLL2, PLL_DIV4 },
+ },
+};
+
+static const struct clockgen_muxinfo t1023_hwa1 = {
+ {
+ {},
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+ },
+};
+
+static const struct clockgen_muxinfo t1023_hwa2 = {
+ {
+ [6] = { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ },
+};
+
+static const struct clockgen_muxinfo t2080_hwa1 = {
+ {
+ {},
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV4 },
+ { CLKSEL_VALID, PLATFORM_PLL, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV3 },
+ },
+};
+
+static const struct clockgen_muxinfo t2080_hwa2 = {
+ {
+ {},
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV3 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV4 },
+ { CLKSEL_VALID, PLATFORM_PLL, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+ },
+};
+
+static const struct clockgen_muxinfo t4240_hwa1 = {
+ {
+ { CLKSEL_VALID, PLATFORM_PLL, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV1 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV3 },
+ { CLKSEL_VALID, CGA_PLL1, PLL_DIV4 },
+ {},
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV2 },
+ { CLKSEL_VALID, CGA_PLL2, PLL_DIV3 },
+ },
+};
+
+static const struct clockgen_muxinfo t4240_hwa4 = {
+ {
+ [2] = { CLKSEL_VALID, CGB_PLL1, PLL_DIV2 },
+ [3] = { CLKSEL_VALID, CGB_PLL1, PLL_DIV3 },
+ [4] = { CLKSEL_VALID, CGB_PLL1, PLL_DIV4 },
+ [5] = { CLKSEL_VALID, PLATFORM_PLL, PLL_DIV1 },
+ [6] = { CLKSEL_VALID, CGB_PLL2, PLL_DIV2 },
+ },
+};
+
+static const struct clockgen_muxinfo t4240_hwa5 = {
+ {
+ [2] = { CLKSEL_VALID, CGB_PLL2, PLL_DIV2 },
+ [3] = { CLKSEL_VALID, CGB_PLL2, PLL_DIV3 },
+ [4] = { CLKSEL_VALID, CGB_PLL2, PLL_DIV4 },
+ [5] = { CLKSEL_VALID, PLATFORM_PLL, PLL_DIV1 },
+ [6] = { CLKSEL_VALID, CGB_PLL1, PLL_DIV2 },
+ [7] = { CLKSEL_VALID, CGB_PLL1, PLL_DIV3 },
+ },
+};
+
+#define RCWSR7_FM1_CLK_SEL 0x40000000
+#define RCWSR7_FM2_CLK_SEL 0x20000000
+#define RCWSR7_HWA_ASYNC_DIV 0x04000000
+
+static void __init p2041_init_periph(struct clockgen *cg)
+{
+ u32 reg;
+
+ reg = ioread32be(&cg->guts->rcwsr[7]);
+
+ if (reg & RCWSR7_FM1_CLK_SEL)
+ cg->fman[0] = cg->pll[CGA_PLL2].div[PLL_DIV2].clk;
+ else
+ cg->fman[0] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+}
+
+static void __init p4080_init_periph(struct clockgen *cg)
+{
+ u32 reg;
+
+ reg = ioread32be(&cg->guts->rcwsr[7]);
+
+ if (reg & RCWSR7_FM1_CLK_SEL)
+ cg->fman[0] = cg->pll[CGA_PLL3].div[PLL_DIV2].clk;
+ else
+ cg->fman[0] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+
+ if (reg & RCWSR7_FM2_CLK_SEL)
+ cg->fman[1] = cg->pll[CGA_PLL3].div[PLL_DIV2].clk;
+ else
+ cg->fman[1] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+}
+
+static void __init p5020_init_periph(struct clockgen *cg)
+{
+ u32 reg;
+ int div = PLL_DIV2;
+
+ reg = ioread32be(&cg->guts->rcwsr[7]);
+ if (reg & RCWSR7_HWA_ASYNC_DIV)
+ div = PLL_DIV4;
+
+ if (reg & RCWSR7_FM1_CLK_SEL)
+ cg->fman[0] = cg->pll[CGA_PLL2].div[div].clk;
+ else
+ cg->fman[0] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+}
+
+static void __init p5040_init_periph(struct clockgen *cg)
+{
+ u32 reg;
+ int div = PLL_DIV2;
+
+ reg = ioread32be(&cg->guts->rcwsr[7]);
+ if (reg & RCWSR7_HWA_ASYNC_DIV)
+ div = PLL_DIV4;
+
+ if (reg & RCWSR7_FM1_CLK_SEL)
+ cg->fman[0] = cg->pll[CGA_PLL3].div[div].clk;
+ else
+ cg->fman[0] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+
+ if (reg & RCWSR7_FM2_CLK_SEL)
+ cg->fman[1] = cg->pll[CGA_PLL3].div[div].clk;
+ else
+ cg->fman[1] = cg->pll[PLATFORM_PLL].div[PLL_DIV2].clk;
+}
+
+static void __init t1023_init_periph(struct clockgen *cg)
+{
+ cg->fman[0] = cg->hwaccel[1];
+}
+
+static void __init t1040_init_periph(struct clockgen *cg)
+{
+ cg->fman[0] = cg->pll[PLATFORM_PLL].div[PLL_DIV1].clk;
+}
+
+static void __init t2080_init_periph(struct clockgen *cg)
+{
+ cg->fman[0] = cg->hwaccel[0];
+}
+
+static void __init t4240_init_periph(struct clockgen *cg)
+{
+ cg->fman[0] = cg->hwaccel[3];
+ cg->fman[1] = cg->hwaccel[4];
+}
+
+static const struct clockgen_chipinfo chipinfo[] = {
+ {
+ .compat = "fsl,b4420-clockgen",
+ .guts_compat = "fsl,b4860-device-config",
+ .init_periph = t2080_init_periph,
+ .cmux_groups = {
+ &clockgen2_cmux_cga12, &clockgen2_cmux_cgb
+ },
+ .hwaccel = {
+ &t2080_hwa1
+ },
+ .cmux_to_group = {
+ 0, 1, 1, 1, -1
+ },
+ .pll_mask = 0x3f,
+ .flags = CG_PLL_8BIT,
+ },
+ {
+ .compat = "fsl,b4860-clockgen",
+ .guts_compat = "fsl,b4860-device-config",
+ .init_periph = t2080_init_periph,
+ .cmux_groups = {
+ &clockgen2_cmux_cga12, &clockgen2_cmux_cgb
+ },
+ .hwaccel = {
+ &t2080_hwa1
+ },
+ .cmux_to_group = {
+ 0, 1, 1, 1, -1
+ },
+ .pll_mask = 0x3f,
+ .flags = CG_PLL_8BIT,
+ },
+ {
+ .compat = "fsl,ls1201a-clockgen",
+ .cmux_groups = {
+ &t1023_cmux
+ },
+ .cmux_to_group = {
+ 0, -1
+ },
+ .pll_mask = 0x03,
+ },
+ {
+ .compat = "fsl,p2041-clockgen",
+ .guts_compat = "fsl,qoriq-device-config-1.0",
+ .init_periph = p2041_init_periph,
+ .cmux_groups = {
+ &p2041_cmux_grp1, &p2041_cmux_grp2
+ },
+ .cmux_to_group = {
+ 0, 0, 1, 1, -1
+ },
+ .pll_mask = 0x07,
+ },
+ {
+ .compat = "fsl,p3041-clockgen",
+ .guts_compat = "fsl,qoriq-device-config-1.0",
+ .init_periph = p2041_init_periph,
+ .cmux_groups = {
+ &p2041_cmux_grp1, &p2041_cmux_grp2
+ },
+ .cmux_to_group = {
+ 0, 0, 1, 1, -1
+ },
+ .pll_mask = 0x07,
+ },
+ {
+ .compat = "fsl,p4080-clockgen",
+ .guts_compat = "fsl,qoriq-device-config-1.0",
+ .init_periph = p4080_init_periph,
+ .cmux_groups = {
+ &p4080_cmux_grp1, &p4080_cmux_grp2
+ },
+ .cmux_to_group = {
+ 0, 0, 0, 0, 1, 1, 1, 1
+ },
+ .pll_mask = 0x1f,
+ },
+ {
+ .compat = "fsl,p5020-clockgen",
+ .guts_compat = "fsl,qoriq-device-config-1.0",
+ .init_periph = p5020_init_periph,
+ .cmux_groups = {
+ &p2041_cmux_grp1, &p2041_cmux_grp2
+ },
+ .cmux_to_group = {
+ 0, 1, -1
+ },
+ .pll_mask = 0x07,
+ },
+ {
+ .compat = "fsl,p5040-clockgen",
+ .guts_compat = "fsl,p5040-device-config",
+ .init_periph = p5040_init_periph,
+ .cmux_groups = {
+ &p5040_cmux_grp1, &p5040_cmux_grp2
+ },
+ .cmux_to_group = {
+ 0, 0, 1, 1, -1
+ },
+ .pll_mask = 0x0f,
+ },
+ {
+ .compat = "fsl,t1023-clockgen",
+ .guts_compat = "fsl,t1023-device-config",
+ .init_periph = t1023_init_periph,
+ .cmux_groups = {
+ &t1023_cmux
+ },
+ .hwaccel = {
+ &t1023_hwa1, &t1023_hwa2
+ },
+ .cmux_to_group = {
+ 0, 0, -1
+ },
+ .pll_mask = 0x03,
+ .flags = CG_PLL_8BIT,
+ },
+ {
+ .compat = "fsl,t1040-clockgen",
+ .guts_compat = "fsl,t1040-device-config",
+ .init_periph = t1040_init_periph,
+ .cmux_groups = {
+ &t1040_cmux
+ },
+ .cmux_to_group = {
+ 0, 0, 0, 0, -1
+ },
+ .pll_mask = 0x07,
+ .flags = CG_PLL_8BIT,
+ },
+ {
+ .compat = "fsl,t2080-clockgen",
+ .guts_compat = "fsl,t2080-device-config",
+ .init_periph = t2080_init_periph,
+ .cmux_groups = {
+ &clockgen2_cmux_cga12
+ },
+ .hwaccel = {
+ &t2080_hwa1, &t2080_hwa2
+ },
+ .cmux_to_group = {
+ 0, -1
+ },
+ .pll_mask = 0x07,
+ .flags = CG_PLL_8BIT,
+ },
+ {
+ .compat = "fsl,t4240-clockgen",
+ .guts_compat = "fsl,t4240-device-config",
+ .init_periph = t4240_init_periph,
+ .cmux_groups = {
+ &clockgen2_cmux_cga, &clockgen2_cmux_cgb
+ },
+ .hwaccel = {
+ &t4240_hwa1, NULL, NULL, &t4240_hwa4, &t4240_hwa5
+ },
+ .cmux_to_group = {
+ 0, 0, 1, -1
+ },
+ .pll_mask = 0x3f,
+ .flags = CG_PLL_8BIT,
+ },
+ {},
+};
+
+struct mux_hwclock {
+ struct clk_hw hw;
+ struct clockgen *cg;
+ const struct clockgen_muxinfo *info;
+ u32 __iomem *reg;
+ u8 parent_to_clksel[NUM_MUX_PARENTS];
+ s8 clksel_to_parent[NUM_MUX_PARENTS];
+ int num_parents;
+};
+
+#define to_mux_hwclock(p) container_of(p, struct mux_hwclock, hw)
+#define CLKSEL_MASK 0x78000000
+#define CLKSEL_SHIFT 27
+
+static int mux_set_parent(struct clk_hw *hw, u8 idx)
+{
+ struct mux_hwclock *hwc = to_mux_hwclock(hw);
+ u32 clksel;
+
+ if (idx >= hwc->num_parents)
+ return -EINVAL;
+
+ clksel = hwc->parent_to_clksel[idx];
+ iowrite32be((clksel << CLKSEL_SHIFT) & CLKSEL_MASK, hwc->reg);
+
+ return 0;
+}
+
+static u8 mux_get_parent(struct clk_hw *hw)
+{
+ struct mux_hwclock *hwc = to_mux_hwclock(hw);
+ u32 clksel;
+ s8 ret;
+
+ clksel = (ioread32be(hwc->reg) & CLKSEL_MASK) >> CLKSEL_SHIFT;
+
+ ret = hwc->clksel_to_parent[clksel];
+ if (ret < 0) {
+ pr_err("%s: mux at %p has bad clksel\n", __func__, hwc->reg);
+ return 0;
+ }
+
+ return ret;
+}
+
+static const struct clk_ops cmux_ops = {
+ .get_parent = mux_get_parent,
+ .set_parent = mux_set_parent,
+};
+
+/*
+ * Don't allow setting for now, as the clock options haven't been
+ * sanitized for additional restrictions.
+ */
+static const struct clk_ops hwaccel_ops = {
+ .get_parent = mux_get_parent,
+};
+
+static const struct clockgen_pll_div *get_pll_div(struct clockgen *cg,
+ struct mux_hwclock *hwc,
+ int idx)
+{
+ int pll, div;
+
+ if (!(hwc->info->clksel[idx].flags & CLKSEL_VALID))
+ return NULL;
+
+ pll = hwc->info->clksel[idx].pll;
+ div = hwc->info->clksel[idx].div;
+
+ return &cg->pll[pll].div[div];
+}
+
+static struct clk * __init create_mux_common(struct clockgen *cg,
+ struct mux_hwclock *hwc,
+ const struct clk_ops *ops,
+ unsigned long min_rate,
+ unsigned long pct80_rate,
+ const char *fmt, int idx)
+{
+ struct clk_init_data init = {};
+ struct clk *clk;
+ const struct clockgen_pll_div *div;
+ const char *parent_names[NUM_MUX_PARENTS];
+ char name[32];
+ int i, j;
+
+ snprintf(name, sizeof(name), fmt, idx);
+
+ for (i = 0, j = 0; i < NUM_MUX_PARENTS; i++) {
+ unsigned long rate;
+
+ hwc->clksel_to_parent[i] = -1;
+
+ div = get_pll_div(cg, hwc, i);
+ if (!div)
+ continue;
+
+ rate = clk_get_rate(div->clk);
+
+ if (hwc->info->clksel[i].flags & CLKSEL_80PCT &&
+ rate > pct80_rate)
+ continue;
+ if (rate < min_rate)
+ continue;
+
+ parent_names[j] = div->name;
+ hwc->parent_to_clksel[j] = i;
+ hwc->clksel_to_parent[i] = j;
+ j++;
+ }
+
+ init.name = name;
+ init.ops = ops;
+ init.parent_names = parent_names;
+ init.num_parents = hwc->num_parents = j;
+ init.flags = 0;
+ hwc->hw.init = &init;
+
+ clk = clk_register(NULL, &hwc->hw);
+ if (IS_ERR(clk)) {
+ pr_err("%s: Couldn't register %s: %ld\n", __func__, name,
+ PTR_ERR(clk));
+ kfree(hwc);
+ return NULL;
+ }
+
+ return clk;
+}
+
+static struct clk * __init create_one_cmux(struct clockgen *cg, int idx)
+{
+ struct mux_hwclock *hwc;
+ const struct clockgen_pll_div *div;
+ unsigned long plat_rate, min_rate;
+ u64 pct80_rate;
+ u32 clksel;
+
+ hwc = kzalloc(sizeof(*hwc), GFP_KERNEL);
+ if (!hwc)
+ return NULL;
+
+ hwc->reg = cg->regs + 0x20 * idx;
+ hwc->info = cg->info.cmux_groups[cg->info.cmux_to_group[idx]];
+
+ /*
+ * Find the rate for the default clksel, and treat it as the
+ * maximum rated core frequency. If this is an incorrect
+ * assumption, certain clock options (possibly including the
+ * default clksel) may be inappropriately excluded on certain
+ * chips.
+ */
+ clksel = (ioread32be(hwc->reg) & CLKSEL_MASK) >> CLKSEL_SHIFT;
+ div = get_pll_div(cg, hwc, clksel);
+ if (!div)
+ return NULL;
+
+ pct80_rate = clk_get_rate(div->clk);
+ pct80_rate *= 8;
+ do_div(pct80_rate, 10);
+
+ plat_rate = clk_get_rate(cg->pll[PLATFORM_PLL].div[PLL_DIV1].clk);
+
+ if (cg->info.flags & CG_CMUX_GE_PLAT)
+ min_rate = plat_rate;
+ else
+ min_rate = plat_rate / 2;
+
+ return create_mux_common(cg, hwc, &cmux_ops, min_rate,
+ pct80_rate, "cg-cmux%d", idx);
+}
+
+static struct clk * __init create_one_hwaccel(struct clockgen *cg, int idx)
+{
+ struct mux_hwclock *hwc;
+
+ hwc = kzalloc(sizeof(*hwc), GFP_KERNEL);
+ if (!hwc)
+ return NULL;
+
+ hwc->reg = cg->regs + 0x20 * idx + 0x10;
+ hwc->info = cg->info.hwaccel[idx];
+
+ return create_mux_common(cg, hwc, &hwaccel_ops, 0, 0,
+ "cg-hwaccel%d", idx);
+}
+
+static void __init create_muxes(struct clockgen *cg)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cg->cmux); i++) {
+ if (cg->info.cmux_to_group[i] < 0)
+ break;
+ if (cg->info.cmux_to_group[i] >=
+ ARRAY_SIZE(cg->info.cmux_groups)) {
+ WARN_ON_ONCE(1);
+ continue;
+ }
+
+ cg->cmux[i] = create_one_cmux(cg, i);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(cg->hwaccel); i++) {
+ if (!cg->info.hwaccel[i])
+ continue;
+
+ cg->hwaccel[i] = create_one_hwaccel(cg, i);
+ }
+}
+
+/* Legacy node */
struct cmux_clk {
struct clk_hw hw;
void __iomem *reg;
@@ -27,7 +771,6 @@ struct cmux_clk {
};
#define PLL_KILL BIT(31)
-#define CLKSEL_SHIFT 27
#define CLKSEL_ADJUST BIT(0)
#define to_cmux_clk(p) container_of(p, struct cmux_clk, hw)
@@ -59,7 +802,7 @@ static u8 cmux_get_parent(struct clk_hw *hw)
return clksel;
}
-static const struct clk_ops cmux_ops = {
+static const struct clk_ops legacy_cmux_ops = {
.get_parent = cmux_get_parent,
.set_parent = cmux_set_parent,
};
@@ -128,7 +871,7 @@ static void __init core_mux_init(struct device_node *np)
}
init.name = clk_name;
- init.ops = &cmux_ops;
+ init.ops = &legacy_cmux_ops;
init.parent_names = parent_names;
init.num_parents = count;
init.flags = 0;
@@ -155,6 +898,7 @@ err_name:
kfree(parent_names);
}
+/* Legacy node */
static void __init core_pll_init(struct device_node *np)
{
u32 mult;
@@ -248,30 +992,112 @@ err_map:
iounmap(base);
}
-static void __init sysclk_init(struct device_node *node)
+static struct clk * __init create_sysclk(struct device_node *clockgen,
+ const char *name)
{
struct clk *clk;
- const char *clk_name = node->name;
- struct device_node *np = of_get_parent(node);
u32 rate;
+ if (!of_property_read_u32(clockgen, "clock-frequency", &rate)) {
+ clk = clk_register_fixed_rate(NULL, name, NULL,
+ CLK_IS_ROOT, rate);
+ } else {
+ const char *parent_name;
+
+ clk = of_clk_get(clockgen, 0);
+ if (IS_ERR(clk)) {
+ pr_err("%s: No input clock: %ld\n", __func__,
+ PTR_ERR(clk));
+ return NULL;
+ }
+
+ /* Register the input clock under the desired name. */
+ parent_name = __clk_get_name(clk);
+ clk = clk_register_fixed_factor(NULL, name, parent_name,
+ 0, 1, 1);
+ }
+
+ if (IS_ERR(clk))
+ pr_err("%s: Couldn't register %s: %ld\n", __func__, name,
+ PTR_ERR(clk));
+
+ return clk;
+}
+
+/* Legacy node */
+static void __init sysclk_init(struct device_node *node)
+{
+ struct device_node *np = of_get_parent(node);
+ struct clk *clk;
+
if (!np) {
pr_err("could not get parent node\n");
return;
}
- if (of_property_read_u32(np, "clock-frequency", &rate)) {
- of_node_put(node);
+ clk = create_sysclk(np, "sysclk");
+ of_node_put(np);
+
+ if (!IS_ERR(clk))
+ of_clk_add_provider(node, of_clk_src_simple_get, clk);
+}
+
+static void __init create_one_pll(struct clockgen *cg, int idx)
+{
+ u32 __iomem *reg;
+ u32 mult;
+ struct clockgen_pll *pll = &cg->pll[idx];
+ int i;
+
+ if (!(cg->info.pll_mask & (1 << idx)))
+ return;
+
+ if (idx == PLATFORM_PLL)
+ reg = cg->regs + 0xc00;
+ else
+ reg = cg->regs + 0x800 + 0x20 * (idx - 1);
+
+ /* Get the multiple of PLL */
+ mult = ioread32be(reg);
+
+ /* Check if this PLL is disabled */
+ if (mult & PLL_KILL) {
+ pr_debug("%s(): pll %p disabled\n", __func__, reg);
return;
}
- of_property_read_string(np, "clock-output-names", &clk_name);
+ if ((cg->info.flags & CG_PLL_8BIT) && idx != PLATFORM_PLL)
+ mult = (mult & GENMASK(8, 1)) >> 1;
+ else
+ mult = (mult & GENMASK(6, 1)) >> 1;
- clk = clk_register_fixed_rate(NULL, clk_name, NULL, CLK_IS_ROOT, rate);
- if (!IS_ERR(clk))
- of_clk_add_provider(np, of_clk_src_simple_get, clk);
+ for (i = 0; i < ARRAY_SIZE(pll->div); i++) {
+ struct clk *clk;
+
+ snprintf(pll->div[i].name, sizeof(pll->div[i].name),
+ "cg-pll%d-div%d", idx, i + 1);
+
+ clk = clk_register_fixed_factor(NULL,
+ pll->div[i].name, "cg-sysclk", 0, mult, i + 1);
+ if (IS_ERR(clk)) {
+ pr_err("%s: %s: register failed %ld\n",
+ __func__, pll->div[i].name, PTR_ERR(clk));
+ continue;
+ }
+
+ pll->div[i].clk = clk;
+ }
+}
+
+static void __init create_plls(struct clockgen *cg)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cg->pll); i++)
+ create_one_pll(cg, i);
}
+/* Legacy node */
static void __init pltfrm_pll_init(struct device_node *np)
{
void __iomem *base;
@@ -352,6 +1178,106 @@ return_clk_unregister:
kfree(cod);
}
+#ifdef CONFIG_PPC
+#include <asm/mpc85xx.h>
+
+static const u32 a4510_svrs[] __initconst = {
+ (SVR_P2040 << 8) | 0x10, /* P2040 1.0 */
+ (SVR_P2040 << 8) | 0x11, /* P2040 1.1 */
+ (SVR_P2041 << 8) | 0x10, /* P2041 1.0 */
+ (SVR_P2041 << 8) | 0x11, /* P2041 1.1 */
+ (SVR_P3041 << 8) | 0x10, /* P3041 1.0 */
+ (SVR_P3041 << 8) | 0x11, /* P3041 1.1 */
+ (SVR_P4040 << 8) | 0x20, /* P4040 2.0 */
+ (SVR_P4080 << 8) | 0x20, /* P4080 2.0 */
+ (SVR_P5010 << 8) | 0x10, /* P5010 1.0 */
+ (SVR_P5010 << 8) | 0x20, /* P5010 2.0 */
+ (SVR_P5020 << 8) | 0x10, /* P5020 1.0 */
+ (SVR_P5021 << 8) | 0x10, /* P5021 1.0 */
+ (SVR_P5040 << 8) | 0x10, /* P5040 1.0 */
+};
+
+#define SVR_SECURITY 0x80000 /* The Security (E) bit */
+
+static bool __init has_erratum_a4510(void)
+{
+ u32 svr = mfspr(SPRN_SVR);
+ int i;
+
+ svr &= ~SVR_SECURITY;
+
+ for (i = 0; i < ARRAY_SIZE(a4510_svrs); i++) {
+ if (svr == a4510_svrs[i])
+ return true;
+ }
+
+ return false;
+}
+#else
+static bool __init has_erratum_a4510(void)
+{
+ return false;
+}
+#endif
+
+static void __init clockgen_init(struct device_node *np)
+{
+ int i;
+
+ clockgen.node = np;
+ clockgen.regs = of_iomap(np, 0);
+ if (!clockgen.regs) {
+ pr_err("%s(): %s: of_iomap() failed\n", __func__, np->name);
+ return;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(chipinfo); i++) {
+ if (of_device_is_compatible(np, chipinfo[i].compat))
+ break;
+ }
+
+ if (i == ARRAY_SIZE(chipinfo)) {
+ pr_err("%s: unknown clockgen node %s\n", __func__,
+ np->full_name);
+ goto err;
+ }
+ clockgen.info = chipinfo[i];
+
+ if (clockgen.info.guts_compat) {
+ struct device_node *guts;
+
+ guts = of_find_compatible_node(NULL, NULL,
+ clockgen.info.guts_compat);
+ if (guts) {
+ clockgen.guts = of_iomap(guts, 0);
+ if (!clockgen.guts) {
+ pr_err("%s: Couldn't map %s regs\n", __func__,
+ guts->full_name);
+ }
+ }
+
+ }
+
+ if (has_erratum_a4510())
+ clockgen.info.flags |= CG_CMUX_GE_PLAT;
+
+ clockgen.sysclk = create_sysclk(np, "cg-sysclk");
+ create_plls(&clockgen);
+ create_muxes(&clockgen);
+
+ if (clockgen.info.init_periph)
+ clockgen.info.init_periph(&clockgen);
+
+ return;
+err:
+ iounmap(clockgen.regs);
+ clockgen.regs = NULL;
+}
+
+CLK_OF_DECLARE(qoriq_clockgen_1, "fsl,qoriq-clockgen-1.0", clockgen_init);
+CLK_OF_DECLARE(qoriq_clockgen_2, "fsl,qoriq-clockgen-2.0", clockgen_init);
+
+/* Legacy nodes */
CLK_OF_DECLARE(qoriq_sysclk_1, "fsl,qoriq-sysclk-1.0", sysclk_init);
CLK_OF_DECLARE(qoriq_sysclk_2, "fsl,qoriq-sysclk-2.0", sysclk_init);
CLK_OF_DECLARE(qoriq_core_pll_1, "fsl,qoriq-core-pll-1.0", core_pll_init);
--
2.1.4
More information about the Linuxppc-dev
mailing list