[PATCH net-next v2] Driver for IBM System i/p VNIC protocol

[Thomas Falcon]

On 12/11/2015 06:53 PM, David Miller wrote:
> From: Thomas Falcon <tlfalcon at linux.vnet.ibm.com>
> Date: Tue,  8 Dec 2015 11:52:19 -0600
>
>> +static long h_reg_sub_crq(unsigned long unit_address, unsigned long token,
>> +			  unsigned long length, unsigned long *number,
>> +			  unsigned long *irq)
>> +{
>> +	long rc;
>> +	unsigned long retbuf[PLPAR_HCALL_BUFSIZE];
> Please declare local variables from longest to shortest line, otherwise
> known as "reverse christmas tree" order.
>
> Audit this in your entire driver.
>
>> +	pool->rx_buff = kcalloc(pool->size, sizeof(struct ibmvnic_rx_buff),
>> +				GFP_KERNEL);
> Allocation failures not checked until much later in this function, where
> several other resources have been allocated meanwhile.  That doesn't
> make any sense at all.
>
>> +	adapter->closing = 1;
> Please use type 'bool' and values 'true' and 'false' for boolean
> values.
>
> Audit this in your entire driver.
>
>> +	if (ip_hdr(skb)->version == 4)
>> +		tx_crq.v1.flags1 |= IBMVNIC_TX_PROT_IPV4;
>> +	else if (ip_hdr(skb)->version == 6)
>> +		tx_crq.v1.flags1 |= IBMVNIC_TX_PROT_IPV6;
>> +
> You cannot dereference the protocol header of the SKB without
> first checking the skb->protocol value, otherwise you're looking
> at garbage.
>
>> +static int ibmvnic_set_mac(struct net_device *netdev, void *p)
>> +{
>> +	struct ibmvnic_adapter *adapter = netdev_priv(netdev);
>> +	struct sockaddr *addr = p;
>> +	union ibmvnic_crq crq;
>> +
>> +	if (!is_valid_ether_addr(addr->sa_data))
>> +		return -EADDRNOTAVAIL;
>> +
>> +	memset(&crq, 0, sizeof(crq));
>> +	crq.change_mac_addr.first = IBMVNIC_CRQ_CMD;
>> +	crq.change_mac_addr.cmd = CHANGE_MAC_ADDR;
>> +	ether_addr_copy(&crq.change_mac_addr.mac_addr[0], addr->sa_data);
>> +	ibmvnic_send_crq(adapter, &crq);
>> +
>> +	return 0;
>> +}
> You are responsible for copying the new MAC address into dev->dev_addr
> on success.

We do this in another function (handle_change_mac_rsp), which handles the response from firmware indicating whether the CHANGE_MAC_ADDR command was successful.  Is this acceptable? 

Thank you for your review comments and your time.

>
>> +static int ibmvnic_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
>> +			     int cmd)
>> +{
>  ...
>> +	return 0;
>> +}
>> +
>> +static int ibmvnic_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
>> +{
>> +	switch (cmd) {
>> +	case SIOCGMIIPHY:
>> +	case SIOCGMIIREG:
>> +	case SIOCSMIIREG:
>> +		return ibmvnic_mii_ioctl(netdev, ifr, cmd);
>> +	default:
>> +		return -EOPNOTSUPP;
>> +	}
>> +}
> This really doesn't make any sense.  Please just delete this.  You
> don't support MII reads or writes because they logically don't make
> sense on this device.
>
>> +static struct net_device_stats *ibmvnic_get_stats(struct net_device *dev)
>> +{
>> +	struct ibmvnic_adapter *adapter = netdev_priv(dev);
>> +
>> +	/* only return the current stats */
>> +	return &adapter->net_stats;
>> +}
> The default method does this for you as long as you properly use
> net_device's embedded stats, therefore you don't need to provide this
> at all.
>
> That's all I have any energy for, and as you can see nobody else wants
> to even try to review this driver.
>
> It's going to take a lot of respins and time before this driver is
> ready for upstream inclusion.
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev