[PATCH] powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()

[Gavin Shan]

The config space of some PCI devices can't be accessed when their
PEs are in frozen state. Otherwise, fenced PHB might be seen.
Those PEs are identified with flag EEH_PE_CFG_RESTRICTED, meaing
EEH_PE_CFG_BLOCKED is set automatically when the PE is put to
frozen state (EEH_PE_ISOLATED). eeh_slot_error_detail() restores
PCI device BARs with eeh_pe_restore_bars(), which then calls
eeh_ops->restore_config() to reinitialize the PCI device in
(OPAL) firmware. eeh_ops->restore_config() produces PCI config
access that causes fenced PHB. The problem was reported on below
adapter:

   0001:01:00.0 0200: 14e4:168e (rev 10)
   0001:01:00.0 Ethernet controller: Broadcom Corporation \
                NetXtreme II BCM57810 10 Gigabit Ethernet (rev 10)

This fixes the issue by skipping eeh_pe_restore_bars() in
eeh_slot_error_detail() when EEH_PE_CFG_BLOCKED is set for the PE.

Fixes: b6541db1 ("powerpc/eeh: Block PCI config access upon frozen PE")
Cc: stable at vger.kernel.org # v4.0+
Reported-by: Manvanthara B. Puttashankar <mputtash at in.ibm.com>
Signed-off-by: Gavin Shan <gwshan at linux.vnet.ibm.com>
---
 arch/powerpc/kernel/eeh.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/kernel/eeh.c b/arch/powerpc/kernel/eeh.c
index af9b597..c7c6e5d 100644
--- a/arch/powerpc/kernel/eeh.c
+++ b/arch/powerpc/kernel/eeh.c
@@ -308,11 +308,26 @@ void eeh_slot_error_detail(struct eeh_pe *pe, int severity)
 	if (!(pe->type & EEH_PE_PHB)) {
 		if (eeh_has_flag(EEH_ENABLE_IO_FOR_LOG))
 			eeh_pci_enable(pe, EEH_OPT_THAW_MMIO);
+
+		/*
+		 * The config space of some PCI devices can't be accessed
+		 * when their PEs are in frozen state. Otherwise, fenced
+		 * PHB might be seen. Those PEs are identified with flag
+		 * EEH_PE_CFG_RESTRICTED, indicating EEH_PE_CFG_BLOCKED
+		 * is set automatically when the PE is put to EEH_PE_ISOLATED.
+		 *
+		 * Restoring BARs possibly triggers PCI config access in
+		 * (OPAL) firmware and then causes fenced PHB. If the
+		 * PCI config is blocked with flag EEH_PE_CFG_BLOCKED, it's
+		 * pointless to restore BARs and dump config space.
+		 */
 		eeh_ops->configure_bridge(pe);
-		eeh_pe_restore_bars(pe);
+		if (!(pe->state & EEH_PE_CFG_BLOCKED)) {
+			eeh_pe_restore_bars(pe);
 
-		pci_regs_buf[0] = 0;
-		eeh_pe_traverse(pe, eeh_dump_pe_log, &loglen);
+			pci_regs_buf[0] = 0;
+			eeh_pe_traverse(pe, eeh_dump_pe_log, &loglen);
+		}
 	}
 
 	eeh_ops->get_log(pe, severity, pci_regs_buf, loglen);
-- 
2.1.0