[PATCH 4/4] dt/bindings: Introduce the FSL QorIQ DPAA QMan portal(s)

[Scott Wood]

On Wed, 2014-10-22 at 09:09 -0500, Emil Medve wrote:
> +- fsl,liodn
> +	Usage:		See pamu.txt
> +	Value type:	<prop-encoded-array>
> +	Definition:	PAMU property used for static LIODN assignment

There are two LIODNs on these nodes; you need to specifiy here which is
which.  Likewise on the crypto subnode.

> +The currently support sub-nodes are:
> +	* fman at 0
> +	* fman at 1
> +	* pme at 0
> +	* crypto at 0

s/support/supported/

> +These subnodes should have the following properties:
> +
> +- fsl,liodn
> +	Usage:		See pamu.txt
> +	Value type:	<prop-encoded-array>
> +	Definition:	PAMU property used for static LIODN assignment
> +
> +- fsl,iommu-parent
> +	Usage:		See pamu.txt
> +	Value type:	<phandle>
> +	Definition:	PAMU property used for dynamic LIODN assignment
> +
> +- dev-handle
> +	Usage:		Required
> +	Value type:	<phandle>
> +	Definition:	The phandle to the particular hardware device that this
> +			portal is connected to.
> +
> +DPAA QMan Pool Channel Nodes
> +
> +Pool Channels are defined with the following properties.
> +
> +PROPERTIES
> +
> +- compatible
> +	Usage:		Required
> +	Value type:	<stringlist>
> +	Definition:	Must include "fsl,qman-pool-channel"
> +			May include "fsl,<SoC>-qman-pool-channel"
> +
> +- fsl,qman-channel-id
> +	Usage:		Required
> +	Value type:	<u32>
> +	Definition:	The hardware index of the channel. This can also be
> +			determined by dividing any of the channel's 8 work queue
> +			IDs by 8
> +
> +EXAMPLE
> +
> +The example below shows a (P4080) BMan portals container/bus node with two portals
> +
> +	qman-portals at ff4200000 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "simple-bus";
> +		ranges = <0 0xf 0xf4200000 0x200000>;
> +
> +		qman-portal at 0 {
> +			cell-index = <0>;
> +			compatible = "fsl,qman-portal-1.2.0", "fsl,qman-portal";
> +			reg = <0 0x4000 0x100000 0x1000>;
> +			interrupts = <104 2 0 0>;
> +			fsl,liodn = <1 2>;
> +			fsl,qman-channel-id = <0>;
> +
> +			fman at 0 {
> +				fsl,liodn = <0x21>;
> +				dev-handle = <&fman0>;
> +			};
> +			fman at 1 {
> +				fsl,liodn = <0xa1>;
> +				dev-handle = <&fman1>;
> +			};
> +			crypto at 0 {
> +				fsl,liodn = <0x41 0x66>;
> +				dev-handle = <&crypto>;
> +			};

Shouldn't have unit address without reg; use fman0/fman1/crypto instead.

-Scott