[PATCH V9 00/18] Enable SRIOV on PowerNV
Gavin Shan
gwshan at linux.vnet.ibm.com
Wed Nov 19 10:11:25 AEDT 2014
On Sun, Nov 02, 2014 at 11:41:16PM +0800, Wei Yang wrote:
Hello Bjorn,
Did you have available bandwidth to review it? :-)
Thanks,
Gavin
>This patchset enables the SRIOV on POWER8.
>
>The gerneral idea is put each VF into one individual PE and allocate required
>resources like MMIO/DMA/MSI. The major difficulty comes from the MMIO
>allocation and adjustment for PF's IOV BAR.
>
>On P8, we use M64BT to cover a PF's IOV BAR, which could make an individual VF
>sit in its own PE. This gives more flexiblity, while at the mean time it
>brings on some restrictions on the PF's IOV BAR size and alignment.
>
>To achieve this effect, we need to do some hack on pci devices's resources.
>1. Expand the IOV BAR properly.
> Done by pnv_pci_ioda_fixup_iov_resources().
>2. Shift the IOV BAR properly.
> Done by pnv_pci_vf_resource_shift().
>3. IOV BAR alignment is calculated by arch dependent function instead of an
> individual VF BAR size.
> Done by pnv_pcibios_sriov_resource_alignment().
>4. Take the IOV BAR alignment into consideration in the sizing and assigning.
> This is achieved by commit: "PCI: Take additional IOV BAR alignment in
> sizing and assigning"
>
>Test Environment:
> The SRIOV device tested is Emulex Lancer(10df:e220) and
> Mellanox ConnectX-3(15b3:1003) on POWER8.
>
>Examples on pass through a VF to guest through vfio:
> 1. unbind the original driver and bind to vfio-pci driver
> echo 0000:06:0d.0 > /sys/bus/pci/devices/0000:06:0d.0/driver/unbind
> echo 1102 0002 > /sys/bus/pci/drivers/vfio-pci/new_id
> Note: this should be done for each device in the same iommu_group
> 2. Start qemu and pass device through vfio
> /home/ywywyang/git/qemu-impreza/ppc64-softmmu/qemu-system-ppc64 \
> -M pseries -m 2048 -enable-kvm -nographic \
> -drive file=/home/ywywyang/kvm/fc19.img \
> -monitor telnet:localhost:5435,server,nowait -boot cd \
> -device "spapr-pci-vfio-host-bridge,id=CXGB3,iommu=26,index=6"
>
>Verify this is the exact VF response:
> 1. ping from a machine in the same subnet(the broadcast domain)
> 2. run arp -n on this machine
> 9.115.251.20 ether 00:00:c9:df:ed:bf C eth0
> 3. ifconfig in the guest
> # ifconfig eth1
> eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
> inet 9.115.251.20 netmask 255.255.255.0 broadcast 9.115.251.255
> inet6 fe80::200:c9ff:fedf:edbf prefixlen 64 scopeid 0x20<link>
> ether 00:00:c9:df:ed:bf txqueuelen 1000 (Ethernet)
> RX packets 175 bytes 13278 (12.9 KiB)
> RX errors 0 dropped 0 overruns 0 frame 0
> TX packets 58 bytes 9276 (9.0 KiB)
> TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
> 4. They have the same MAC address
>
> Note: make sure you shutdown other network interfaces in guest.
>
>---
>v9:
> * make the change log consistent in the terminology
> PF's IOV BAR -> the SRIOV BAR in PF
> VF's BAR -> the normal BAR in VF's view
> * rename all newly introduced function from _sriov_ to _iov_
> * rename the document to Documentation/powerpc/pci_iov_resource_on_powernv.txt
> * add the vendor id and device id of the tested devices
> * change return value from EINVAL to ENOSYS for pci_iov_virtfn_bus() and
> pci_iov_virtfn_devfn() when it is called on PF or SRIOV is not configured
> * rebase on 3.18-rc2 and tested
>v8:
> * use weak funcion pcibios_sriov_resource_size() instead of some flag to
> retrieve the IOV BAR size.
> * add a document Documentation/powerpc/pci_resource.txt to explain the
> design.
> * make pci_iov_virtfn_bus()/pci_iov_virtfn_devfn() not inline.
> * extract a function res_to_dev_res(), so that it is more general to get
> additional size and alignment
> * fix one contention which is introduced in "powrepc/pci: Refactor pci_dn".
> the root cause is pci_get_slot() takes pci_bus_sem and leads to dead
> lock.
>v7:
> * add IORESOURCE_ARCH flag for IOV BAR on powernv platform.
> * when IOV BAR has IORESOURCE_ARCH flag, the size is retrieved from
> hardware directly. If not, calculate as usual.
> * reorder the patch set, group them by subsystem:
> PCI, powerpc, powernv
> * rebase it on 3.16-rc6
>v6:
> * remove pcibios_enable_sriov()/pcibios_disable_sriov() weak function
> similar function is moved to
> pnv_pci_enable_device_hook()/pnv_pci_disable_device_hook(). When PF is
> enabled, platform will try best to allocate resources for VFs.
> * remove pcibios_sriov_resource_size weak function
> * VF BAR size is retrieved from hardware directly in virtfn_add()
>v5:
> * merge those SRIOV related platform functions in machdep_calls
> wrap them in one CONFIG_PCI_IOV marco
> * define IODA_INVALID_M64 to replace (-1)
> use this value to represent the m64_wins is not used
> * rename pnv_pci_release_dev_dma() to pnv_pci_ioda2_release_dma_pe()
> this function is a conterpart to pnv_pci_ioda2_setup_dma_pe()
> * change dev_info() to dev_dgb() in pnv_pci_ioda_fixup_iov_resources()
> reduce some log in kernel
> * release M64 window in pnv_pci_ioda2_release_dma_pe()
>v4:
> * code format fix, eg. not exceed 80 chars
> * in commit "ppc/pnv: Add function to deconfig a PE"
> check the bus has a bridge before print the name
> remove a PE from its own PELTV
> * change the function name for sriov resource size/alignment
> * rebase on 3.16-rc3
> * VFs will not rely on device node
> As Grant Likely's comments, kernel should have the ability to handle the
> lack of device_node gracefully. Gavin restructure the pci_dn, which
> makes the VF will have pci_dn even when VF's device_node is not provided
> by firmware.
> * clean all the patch title to make them comply with one style
> * fix return value for pci_iov_virtfn_bus/pci_iov_virtfn_devfn
>v3:
> * change the return type of virtfn_bus/virtfn_devfn to int
> change the name of these two functions to pci_iov_virtfn_bus/pci_iov_virtfn_devfn
> * reduce the second parameter or pcibios_sriov_disable()
> * use data instead of pe in "ppc/pnv: allocate pe->iommu_table dynamically"
> * rename __pci_sriov_resource_size to pcibios_sriov_resource_size
> * rename __pci_sriov_resource_alignment to pcibios_sriov_resource_alignment
>v2:
> * change the return value of virtfn_bus/virtfn_devfn to 0
> * move some TCE related marco definition to
> arch/powerpc/platforms/powernv/pci.h
> * fix the __pci_sriov_resource_alignment on powernv platform
> During the sizing stage, the IOV BAR is truncated to 0, which will
> effect the order of allocation. Fix this, so that make sure BAR will be
> allocated ordered by their alignment.
>v1:
> * improve the change log for
> "PCI: Add weak __pci_sriov_resource_size() interface"
> "PCI: Add weak __pci_sriov_resource_alignment() interface"
> "PCI: take additional IOV BAR alignment in sizing and assigning"
> * wrap VF PE code in CONFIG_PCI_IOV
> * did regression test on P7.
>
>Gavin Shan (1):
> powrepc/pci: Refactor pci_dn
>
>Wei Yang (17):
> PCI/IOV: Export interface for retrieve VF's BDF
> PCI: Add weak pcibios_iov_resource_alignment() interface
> PCI: Add weak pcibios_iov_resource_size() interface
> PCI: Take additional PF's IOV BAR alignment in sizing and assigning
> powerpc/pci: Add PCI resource alignment documentation
> powerpc/pci: Don't unset pci resources for VFs
> powerpc/pci: Define pcibios_disable_device() on powerpc
> powerpc/pci: remove pci_dn->pcidev field
> powerpc/powernv: Use pci_dn in PCI config accessor
> powerpc/powernv: Allocate pe->iommu_table dynamically
> powerpc/powernv: Expand VF resources according to the number of
> total_pe
> powerpc/powernv: Implement pcibios_iov_resource_alignment() on
> powernv
> powerpc/powernv: Implement pcibios_iov_resource_size() on powernv
> powerpc/powernv: Shift VF resource with an offset
> powerpc/powernv: Allocate VF PE
> powerpc/powernv: Expanding IOV BAR, with m64_per_iov supported
> powerpc/powernv: Group VF PE when IOV BAR is big on PHB3
>
> .../powerpc/pci_iov_resource_on_powernv.txt | 75 ++
> arch/powerpc/include/asm/device.h | 3 +
> arch/powerpc/include/asm/iommu.h | 3 +
> arch/powerpc/include/asm/machdep.h | 13 +-
> arch/powerpc/include/asm/pci-bridge.h | 24 +-
> arch/powerpc/kernel/pci-common.c | 39 +
> arch/powerpc/kernel/pci-hotplug.c | 3 +
> arch/powerpc/kernel/pci_dn.c | 257 ++++++-
> arch/powerpc/platforms/powernv/eeh-powernv.c | 14 +-
> arch/powerpc/platforms/powernv/pci-ioda.c | 744 +++++++++++++++++++-
> arch/powerpc/platforms/powernv/pci.c | 87 +--
> arch/powerpc/platforms/powernv/pci.h | 13 +-
> drivers/pci/iov.c | 60 +-
> drivers/pci/setup-bus.c | 85 ++-
> include/linux/pci.h | 19 +
> 15 files changed, 1332 insertions(+), 107 deletions(-)
> create mode 100644 Documentation/powerpc/pci_iov_resource_on_powernv.txt
>
>--
>1.7.9.5
>
More information about the Linuxppc-dev
mailing list