[PATCH][v2] powerpc/mpc85xx: Add BSC9132 QDS Support
Harninder Rai
harninder.rai at freescale.com
Thu May 15 17:45:33 EST 2014
- BSC9132 is an integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 technologies
with MAPLE-B2F baseband acceleration processing elements
- BSC9132QDS Overview
2Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Signed-off-by: Harninder Rai <harninder.rai at freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta at freescale.com>
---
Changes since base version:
Incorporated Scott's comment
- Remove flash partition information from device tree
.../devicetree/bindings/powerpc/fsl/board.txt | 17 ++
arch/powerpc/boot/dts/bsc9132qds.dts | 35 ++++
arch/powerpc/boot/dts/bsc9132qds.dtsi | 101 +++++++++++
arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi | 185 ++++++++++++++++++++
arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi | 66 +++++++
arch/powerpc/platforms/85xx/Kconfig | 9 +
arch/powerpc/platforms/85xx/Makefile | 1 +
arch/powerpc/platforms/85xx/bsc913x_qds.c | 74 ++++++++
8 files changed, 488 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/bsc9132qds.dts
create mode 100644 arch/powerpc/boot/dts/bsc9132qds.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi
create mode 100644 arch/powerpc/platforms/85xx/bsc913x_qds.c
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/board.txt b/Documentation/devicetree/bindings/powerpc/fsl/board.txt
index 380914e..700dec4 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/board.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/board.txt
@@ -67,3 +67,20 @@ Example:
gpio-controller;
};
};
+
+* Freescale on-board FPGA connected on I2C bus
+
+Some Freescale boards like BSC9132QDS have on board FPGA connected on
+the i2c bus.
+
+Required properties:
+- compatible: Should be a board-specific string followed by a string
+ indicating the type of FPGA. Example:
+ "fsl,<board>-fpga", "fsl,fpga-qixis-i2c"
+- reg: Should contain the address of the FPGA
+
+Example:
+ fpga: fpga at 66 {
+ compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
+ reg = <0x66>;
+ };
diff --git a/arch/powerpc/boot/dts/bsc9132qds.dts b/arch/powerpc/boot/dts/bsc9132qds.dts
new file mode 100644
index 0000000..6cab106
--- /dev/null
+++ b/arch/powerpc/boot/dts/bsc9132qds.dts
@@ -0,0 +1,35 @@
+/*
+ * BSC9132 QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/bsc9132si-pre.dtsi"
+
+/ {
+ model = "fsl,bsc9132qds";
+ compatible = "fsl,bsc9132qds";
+
+ memory {
+ device_type = "memory";
+ };
+
+ ifc: ifc at ff71e000 {
+ /* NOR, NAND Flash on board */
+ ranges = <0x0 0x0 0x0 0x88000000 0x08000000
+ 0x1 0x0 0x0 0xff800000 0x00010000>;
+ reg = <0x0 0xff71e000 0x0 0x2000>;
+ };
+
+ soc: soc at ff700000 {
+ ranges = <0x0 0x0 0xff700000 0x100000>;
+ };
+};
+
+/include/ "bsc9132qds.dtsi"
+/include/ "fsl/bsc9132si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/bsc9132qds.dtsi b/arch/powerpc/boot/dts/bsc9132qds.dtsi
new file mode 100644
index 0000000..af8e888
--- /dev/null
+++ b/arch/powerpc/boot/dts/bsc9132qds.dtsi
@@ -0,0 +1,101 @@
+/*
+ * BSC9132 QDS Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ nor at 0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand at 1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x4000>;
+ };
+};
+
+&soc {
+ spi at 7000 {
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <30000000>;
+ };
+ };
+
+ i2c at 3000 {
+ fpga: fpga at 66 {
+ compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
+ reg = <0x66>;
+ };
+ };
+
+ usb at 22000 {
+ phy_type = "ulpi";
+ };
+
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x1f>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy1>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi b/arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi
new file mode 100644
index 0000000..c723071
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi
@@ -0,0 +1,185 @@
+/*
+ * BSC9132 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ /* FIXME: Test whether interrupts are split */
+ interrupts = <16 2 0 0 20 2 0 0>;
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,bsc9132-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law at 0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm at 1000 {
+ compatible = "fsl,bsc9132-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller at 2000 {
+ compatible = "fsl,bsc9132-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 1 8>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+ i2c at 3000 {
+ interrupts = <17 2 0 0>;
+ };
+
+/include/ "pq3-i2c-1.dtsi"
+ i2c at 3100 {
+ interrupts = <17 2 0 0>;
+ };
+
+/include/ "pq3-duart-0.dtsi"
+ serial0: serial at 4500 {
+ interrupts = <18 2 0 0>;
+ };
+
+ serial1: serial at 4600 {
+ interrupts = <18 2 0 0 >;
+ };
+/include/ "pq3-espi-0.dtsi"
+ spi0: spi at 7000 {
+ fsl,espi-num-chipselects = <1>;
+ interrupts = <22 0x2 0 0>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+ gpio-controller at f000 {
+ interrupts = <19 0x2 0 0>;
+ };
+
+ L2: l2-cache-controller at 20000 {
+ compatible = "fsl,bsc9132-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 1 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+
+dma at 21300 {
+
+ dma-channel at 0 {
+ interrupts = <62 2 0 0>;
+ };
+
+ dma-channel at 80 {
+ interrupts = <63 2 0 0>;
+ };
+
+ dma-channel at 100 {
+ interrupts = <64 2 0 0>;
+ };
+
+ dma-channel at 180 {
+ interrupts = <65 2 0 0>;
+ };
+};
+
+/include/ "pq3-usb2-dr-0.dtsi"
+usb at 22000 {
+ compatible = "fsl-usb2-dr","fsl-usb2-dr-v2.2";
+ interrupts = <40 0x2 0 0>;
+};
+
+/include/ "pq3-esdhc-0.dtsi"
+ sdhc at 2e000 {
+ fsl,sdhci-auto-cmd12;
+ interrupts = <41 0x2 0 0>;
+ };
+
+/include/ "pq3-sec4.4-0.dtsi"
+crypto at 30000 {
+ interrupts = <57 2 0 0>;
+
+ sec_jr0: jr at 1000 {
+ interrupts = <58 2 0 0>;
+ };
+
+ sec_jr1: jr at 2000 {
+ interrupts = <59 2 0 0>;
+ };
+
+ sec_jr2: jr at 3000 {
+ interrupts = <60 2 0 0>;
+ };
+
+ sec_jr3: jr at 4000 {
+ interrupts = <61 2 0 0>;
+ };
+};
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+enet0: ethernet at b0000 {
+ queue-group at b0000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ interrupts = <26 2 0 0 27 2 0 0 28 2 0 0>;
+ };
+};
+
+/include/ "pq3-etsec2-1.dtsi"
+enet1: ethernet at b1000 {
+ queue-group at b1000 {
+ fsl,rx-bit-map = <0xff>;
+ fsl,tx-bit-map = <0xff>;
+ interrupts = <33 2 0 0 34 2 0 0 35 2 0 0>;
+ };
+};
+
+global-utilities at e0000 {
+ compatible = "fsl,bsc9132-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
diff --git a/arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi b/arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi
new file mode 100644
index 0000000..301a9db
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi
@@ -0,0 +1,66 @@
+/*
+ * BSC9132 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e500v2_power_isa.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500v2 at 0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu1: PowerPC,e500v2 at 1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index c17aae8..4bd7223 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -38,6 +38,15 @@ config C293_PCIE
help
This option enables support for the C293PCIE board
+config BSC9132_QDS
+ bool "Freescale BSC9132QDS"
+ select DEFAULT_UIMAGE
+ help
+ This option enables support for the Freescale BSC9132 QDS board.
+ BSC9132 is a heterogeneous SoC containing dual e500v2 powerpc cores
+ and dual StarCore SC3850 DSP cores.
+ Manufacturer : Freescale Semiconductor, Inc
+
config MPC8540_ADS
bool "Freescale MPC8540 ADS"
select DEFAULT_UIMAGE
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 25cebe7..c19beb9 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_SMP) += smp.o
obj-y += common.o
obj-$(CONFIG_BSC9131_RDB) += bsc913x_rdb.o
+obj-$(CONFIG_BSC9132_QDS) += bsc913x_qds.o
obj-$(CONFIG_C293_PCIE) += c293pcie.o
obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o
diff --git a/arch/powerpc/platforms/85xx/bsc913x_qds.c b/arch/powerpc/platforms/85xx/bsc913x_qds.c
new file mode 100644
index 0000000..f0927e5
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/bsc913x_qds.c
@@ -0,0 +1,74 @@
+/*
+ * BSC913xQDS Board Setup
+ *
+ * Author:
+ * Harninder Rai <harninder.rai at freescale.com>
+ * Priyanka Jain <Priyanka.Jain at freescale.com>
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <asm/mpic.h>
+#include <sysdev/fsl_soc.h>
+#include <asm/udbg.h>
+
+#include "mpc85xx.h"
+#include "smp.h"
+
+void __init bsc913x_qds_pic_init(void)
+{
+ struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
+ MPIC_SINGLE_DEST_CPU,
+ 0, 256, " OpenPIC ");
+
+ if (!mpic)
+ pr_err("bsc913x: Failed to allocate MPIC structure\n");
+ else
+ mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init bsc913x_qds_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("bsc913x_qds_setup_arch()", 0);
+
+#if defined(CONFIG_SMP)
+ mpc85xx_smp_init();
+#endif
+
+ pr_info("bsc913x board from Freescale Semiconductor\n");
+}
+
+machine_device_initcall(bsc9132_qds, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+
+static int __init bsc9132_qds_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "fsl,bsc9132qds");
+}
+
+define_machine(bsc9132_qds) {
+ .name = "BSC9132 QDS",
+ .probe = bsc9132_qds_probe,
+ .setup_arch = bsc913x_qds_setup_arch,
+ .init_IRQ = bsc913x_qds_pic_init,
+ .get_irq = mpic_get_irq,
+ .restart = fsl_rstcr_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
--
1.7.6.GIT
More information about the Linuxppc-dev
mailing list