[PATCH] [v2] power/fsl: add MDIO dt binding for FMan

[Scott Wood]

On Mon, 2014-12-22 at 02:20 -0600, Emil Medve wrote:
> Hello Shao-Hui,
> 
> 
> On 12/21/2014 08:31 PM, Xie Shaohui-B21989 wrote:
> >> On Fri, 2014-12-19 at 01:23 -0600, Xie Shaohui-B21989 wrote:
> >>>> -----Original Message-----
> >>>> From: Wood Scott-B07421
> >>>> Sent: Friday, December 19, 2014 6:01 AM
> >>>> To: Xie Shaohui-B21989
> >>>> Cc: linuxppc-dev at lists.ozlabs.org; devicetree at vger.kernel.org; Medve
> >>>> Emilian- EMMEDVE1; Liberman Igal-B31950
> >>>> Subject: Re: [PATCH] [v2] power/fsl: add MDIO dt binding for FMan
> >>>>
> >>>> On Thu, 2014-12-18 at 06:53 -0600, Xie Shaohui-B21989 wrote:
> >>>>> Ping.
> >>>>>
> >>>>> Best Regards,
> >>>>> Shaohui Xie
> >>>>
> >>>> I can't put patches in my -next until the merge window closes.
> >>>>
> >>>>>>>> +EXAMPLE
> >>>>>>>> +
> >>>>>>>> +Example for FMan v2 external MDIO:
> >>>>>>>> +
> >>>>>>>> +mdio at f1000 {
> >>>>>>>> +	compatible = "fsl,fman-xmdio";
> >>>>>>>> +	reg = <0xf1000 0x1000>;
> >>>>>>>> +	bus-frequency = <20000>;
> >>>>>>>> +};
> >>>>>>>
> >>>>>>> So the bus frequency is only 20 KHz?  Or is the unit supposed
> >>>>>>> to be something other than Hz?
> >>>>>> [S.H] it's only an example, it could be different on real SoCs,
> >>>>>> but they always lower than the standard one, The standard one is
> >>>>>> 2.5MHz, I have
> >>>> to use Hz for it.
> >>>>
> >>>> Is there any SoC for which 20 kHz is the right frequency?  I just
> >>>> want to make sure the example is realistic.
> >>> [S.H] the clock divider has a limitation that the MAX value it can get
> >>> on Fman v2 is 255 (0xff, 8 bits), On Fman v3 is 511(0x1ff, 9 bits).
> >>>
> >>> So the lowest frequency on Fman v2 is: Fman_clock / (2 * 255), On Fman
> >>> v3 is: Fman_clock / ((2 * 511) + 1).
> >>>
> >>> Take default Fman frequency setting from SDK1.7 as example, the lowest
> >>> clock used for Fman v2 is 581MHz, The lowest clock for Fman v3 is 600MHz.
> >>>
> >>> Then the lowest bus frequency can get is:
> >>> Fman v2: ~1140KHz
> >>> Fman v3: ~587KHz
> >>>
> >>> 20KHz is not practice, we don't have a suggested value in errata document.
> >>> For this example, should I post a new version with a value like 1200KHz?
> >>
> >> This is different from how you described the problem before.  If the limitation
> >> is on the divider, rather than the absolute bus frequency, then specifiy the max
> >> divider.  Or better, since according to the above this correlates with fman
> >> version, just have the driver know what the max divider is for each fman version.
> > [S.H] The problem is not the divider has limitation, the problem is a different bus frequency 
> > Is needed which is lower than the standard, but due to the divider limitation, the lowest
> > bus frequency also has limitation. i.e. we need to use the divider to get a lower frequency,
> > but how much lower the value could be is restricted by the divider limitation.

This is difficult to follow -- are you saying the erratum requires a
speed that is not achievable?

> For the purpose of an example in the binding document, I suggest we just
> stick with the IEEE standard frequency.

The whole reason for this property existing in the device tree is
non-standard frequencies.

> We can continue this conversation about errata handling when we submit
> the code relevant to this binding (and the FMan v3 support)

It affects the binding, so let's discuss it now please.

-Scott