[PATCH 1/2][v3] powerpc/fsl-booke: Add initial T1040/T1042 RDB board support
Emil Medve
Emilian.Medve at Freescale.com
Thu Aug 28 05:04:29 EST 2014
Hello Priyanka,
On 08/11/2014 02:18 AM, Priyanka Jain wrote:
> T1040/T1042RDB is Freescale Reference Design Board.
> The board can support both T1040/T1042 QorIQ Power Architecture™ processor.
>
> T1040/T1042RDB board Overview
> -----------------------
> - SERDES Connections, 8 lanes supporting:
> - PCI
> - SGMII
> - QSGMII
> - SATA 2.0
> - DDR Controller
> - Supports rates of up to 1600 MHz data-rate
> - Supports one DDR3LP UDIMM
> -IFC/Local Bus
> - NAND flash: 1GB 8-bit NAND flash
> - NOR: 128MB 16-bit NOR Flash
> - Ethernet
> - Two on-board RGMII 10/100/1G ethernet ports.
> - PHY #0 remains powered up during deep-sleep
> - CPLD
> - Clocks
> - System and DDR clock (SYSCLK, “DDRCLK”)
> - SERDES clocks
> - Power Supplies
> - USB
> - Supports two USB 2.0 ports with integrated PHYs
> - Two type A ports with 5V at 1.5A per port.
> - SDHC
> - SDHC/SDXC connector
> - SPI
> - On-board 64MB SPI flash
> - I2C
> - Devices connected: EEPROM, thermal monitor, VID controller
> - Other IO
> - Two Serial ports
> - ProfiBus port
>
> Add support for T1040/T1042 RDB board:
> -add device tree
> -add entry in Kconfig to build
> -Add entry in corenet_generic.c, as it is similar to other corenet platforms
>
> Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com>
> Signed-off-by: Poonam Aggrwal <poonam.aggrwal at freescale.com>
> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
> ---
> changes for v3: Incorporated Scott comments on moving cpld compatible
> field to board specific file as cpld binaries are different
>
> changes for v2: Incorporated Scott comments on using common name
> for compatible string for cpld as register set is same
>
> arch/powerpc/boot/dts/t1040rdb.dts | 48 ++++++++
> arch/powerpc/boot/dts/t1042rdb.dts | 48 ++++++++
> arch/powerpc/boot/dts/t104xrdb.dtsi | 156 +++++++++++++++++++++++++
> arch/powerpc/platforms/85xx/Kconfig | 2 +-
> arch/powerpc/platforms/85xx/corenet_generic.c | 2 +
> 5 files changed, 255 insertions(+), 1 deletions(-)
> create mode 100644 arch/powerpc/boot/dts/t1040rdb.dts
> create mode 100644 arch/powerpc/boot/dts/t1042rdb.dts
> create mode 100644 arch/powerpc/boot/dts/t104xrdb.dtsi
>
> diff --git a/arch/powerpc/boot/dts/t1040rdb.dts b/arch/powerpc/boot/dts/t1040rdb.dts
> new file mode 100644
> index 0000000..79a0bed
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/t1040rdb.dts
> @@ -0,0 +1,48 @@
> +/*
> + * T1040RDB Device Tree Source
> + *
> + * Copyright 2014 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +/include/ "fsl/t104xsi-pre.dtsi"
> +/include/ "t104xrdb.dtsi"
> +
> +/ {
> + model = "fsl,T1040RDB";
> + compatible = "fsl,T1040RDB";
I suggest you leave an empty line between the properties and subnodes
> + ifc: localbus at ffe124000 {
> + cpld at 3,0 {
> + compatible = "fsl,t1040rdb-cpld";
> + };
> + };
I believe Scott's point was that you shouldn't have a plethora of
compatibles in a common file for a device that's identical across
boards. If the device is not really identical and a separate compatible
is needed to differentiate it across boards, then the node should move
into the board specific file with different compatibles. Here, you've
moved the CPLD node in the board specific file but you used the same
compatible
> +};
> +
> +/include/ "fsl/t1040si-post.dtsi"
> diff --git a/arch/powerpc/boot/dts/t1042rdb.dts b/arch/powerpc/boot/dts/t1042rdb.dts
> new file mode 100644
> index 0000000..228a635
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/t1042rdb.dts
> @@ -0,0 +1,48 @@
> +/*
> + * T1042RDB Device Tree Source
> + *
> + * Copyright 2014 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +/include/ "fsl/t104xsi-pre.dtsi"
> +/include/ "t104xrdb.dtsi"
> +
> +/ {
> + model = "fsl,T1042RDB";
> + compatible = "fsl,T1042RDB";
> + ifc: localbus at ffe124000 {
> + cpld at 3,0 {
> + compatible = "fsl,t1040rdb-cpld";
> + };
> + };
Same as above
> +};
> +
> +/include/ "fsl/t1042si-post.dtsi"
> diff --git a/arch/powerpc/boot/dts/t104xrdb.dtsi b/arch/powerpc/boot/dts/t104xrdb.dtsi
> new file mode 100644
> index 0000000..1cf0f3c
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/t104xrdb.dtsi
> @@ -0,0 +1,156 @@
> +/*
> + * T1040RDB/T1042RDB Device Tree Source
> + *
> + * Copyright 2014 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +/ {
> +
Remove the empty line
> + ifc: localbus at ffe124000 {
> + reg = <0xf 0xfe124000 0 0x2000>;
> + ranges = <0 0 0xf 0xe8000000 0x08000000
> + 2 0 0xf 0xff800000 0x00010000
> + 3 0 0xf 0xffdf0000 0x00008000>;
> +
> + nor at 0,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "cfi-flash";
> + reg = <0x0 0x0 0x8000000>;
> + bank-width = <2>;
> + device-width = <1>;
> + };
> +
> + nand at 2,0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,ifc-nand";
> + reg = <0x2 0x0 0x10000>;
> + };
> +
> + cpld at 3,0 {
> + reg = <3 0 0x300>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + };
> +
> + dcsr: dcsr at f00000000 {
> + ranges = <0x00000000 0xf 0x00000000 0x01072000>;
> + };
> +
> + soc: soc at ffe000000 {
> + ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
> + reg = <0xf 0xfe000000 0 0x00001000>;
> +
> + spi at 110000 {
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "micron,n25q512a";
> + reg = <0>;
> + spi-max-frequency = <10000000>; /* input clock */
> + };
> + };
> +
> + i2c at 118100 {
> + pca9546 at 77 {
> + compatible = "nxp,pca9546";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +
Remove the empty line
Cheers,
> + };
> +
> + pci0: pcie at ffe240000 {
> + reg = <0xf 0xfe240000 0 0x10000>;
> + ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x10000000
> + 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
> + pcie at 0 {
> + ranges = <0x02000000 0 0xe0000000
> + 0x02000000 0 0xe0000000
> + 0 0x10000000
> +
> + 0x01000000 0 0x00000000
> + 0x01000000 0 0x00000000
> + 0 0x00010000>;
> + };
> + };
> +
> + pci1: pcie at ffe250000 {
> + reg = <0xf 0xfe250000 0 0x10000>;
> + ranges = <0x02000000 0x0 0xe0000000 0xc 0x10000000 0x0 0x10000000
> + 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
> + pcie at 0 {
> + ranges = <0x02000000 0 0xe0000000
> + 0x02000000 0 0xe0000000
> + 0 0x10000000
> +
> + 0x01000000 0 0x00000000
> + 0x01000000 0 0x00000000
> + 0 0x00010000>;
> + };
> + };
> +
> + pci2: pcie at ffe260000 {
> + reg = <0xf 0xfe260000 0 0x10000>;
> + ranges = <0x02000000 0 0xe0000000 0xc 0x20000000 0 0x10000000
> + 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
> + pcie at 0 {
> + ranges = <0x02000000 0 0xe0000000
> + 0x02000000 0 0xe0000000
> + 0 0x10000000
> +
> + 0x01000000 0 0x00000000
> + 0x01000000 0 0x00000000
> + 0 0x00010000>;
> + };
> + };
> +
> + pci3: pcie at ffe270000 {
> + reg = <0xf 0xfe270000 0 0x10000>;
> + ranges = <0x02000000 0 0xe0000000 0xc 0x30000000 0 0x10000000
> + 0x01000000 0 0x00000000 0xf 0xf8030000 0 0x00010000>;
> + pcie at 0 {
> + ranges = <0x02000000 0 0xe0000000
> + 0x02000000 0 0xe0000000
> + 0 0x10000000
> +
> + 0x01000000 0 0x00000000
> + 0x01000000 0 0x00000000
> + 0 0x00010000>;
> + };
> + };
> +};
> diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
> index 5063696..157a1a4 100644
> --- a/arch/powerpc/platforms/85xx/Kconfig
> +++ b/arch/powerpc/platforms/85xx/Kconfig
> @@ -276,7 +276,7 @@ config CORENET_GENERIC
> For 64bit kernel, the following boards are supported:
> T208x QDS, T4240 QDS/RDB and B4 QDS
> The following boards are supported for both 32bit and 64bit kernel:
> - P5020 DS, P5040 DS and T104xQDS
> + P5020 DS, P5040 DS and T104xQDS/RDB
>
> endif # FSL_SOC_BOOKE
>
> diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
> index 4f22ad1..c268f89 100644
> --- a/arch/powerpc/platforms/85xx/corenet_generic.c
> +++ b/arch/powerpc/platforms/85xx/corenet_generic.c
> @@ -128,6 +128,8 @@ static const char * const boards[] __initconst = {
> "fsl,B4220QDS",
> "fsl,T1040QDS",
> "fsl,T1042QDS",
> + "fsl,T1040RDB",
> + "fsl,T1042RDB",
> "keymile,kmcoge4",
> NULL
> };
More information about the Linuxppc-dev
mailing list