[PATCH 1/2][v2] pci: fsl: derive the common PCI driver to drivers/pci/host
Lian Minghuan-b31939
B31939 at freescale.com
Wed Oct 9 21:14:37 EST 2013
Hi Bjorn,
Thanks for your review, please see my comments inline.
On 10/09/2013 03:13 AM, Bjorn Helgaas wrote:
> [+cc Ben, Paul, linuxppc-dev]
>
> On Mon, Sep 30, 2013 at 04:52:54PM +0800, Minghuan Lian wrote:
>> The Freescale's Layerscape series processors will use ARM cores.
>> The LS1's PCIe controllers is the same as T4240's. So it's better
>> the PCIe controller driver can support PowerPC and ARM
>> simultaneously. This patch is for this purpose. It derives
>> the common functions from arch/powerpc/sysdev/fsl_pci.c to
>> drivers/pci/host/pci-fsl-common.c and leaves the architecture
>> specific functions which should be implemented in arch related files.
>>
>> Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
> I cc'd the powerpc maintainers so we can work out which tree this
> should go through.
>
>> ---
>> change log:
>> v1-v2:
>> 1. rename pci.h to pci-common.h
>> 2. rename pci-fsl.c to pci-fsl-common.c
>>
>> Based on upstream master.
>> Based on the discussion of RFC version here
>> http://patchwork.ozlabs.org/patch/274487/
>>
>> arch/powerpc/sysdev/fsl_pci.c | 521 +-----------------
>> arch/powerpc/sysdev/fsl_pci.h | 89 ----
>> .../fsl_pci.c => drivers/pci/host/pci-fsl-common.c | 591 +--------------------
>> .../fsl_pci.h => include/linux/fsl/pci-common.h | 45 +-
> Is there any way to avoid putting this file in include/linux? I know
> you want to share it beyond PowerPC, and I know there are similar
> examples there already, but this is all arch-specific or
> chipset-specific stuff that seems like it should be in some
> not-so-public place. It doesn't seem scalable to add an include/linux
> subdirectory for every chipset that might be shared across
> architectures.
[Minghuan] I can move pci-common.h to drivers/pci/host/
But in arch/powerpc/sysdev/fsl_pci.c I must include the header file
like this:
#include "../../../drivers/pci/host/pci-fsl-common.h"./
/How about this modification?
> I assume this patch basically just moves code around, so the only
> question I really care about is where it ends up.
[Minghuan] patch 2/2 modified the code, removed arch-specific code from
drivers/pci/host/pci-fsl.c. When I verify the pci driver code on LS1
board, I will
submit a patch to support ARM arch.
> Bjorn
>
>> 4 files changed, 7 insertions(+), 1239 deletions(-)
>> copy arch/powerpc/sysdev/fsl_pci.c => drivers/pci/host/pci-fsl-common.c (54%)
>> copy arch/powerpc/sysdev/fsl_pci.h => include/linux/fsl/pci-common.h (79%)
>>
>> diff --git a/arch/powerpc/sysdev/fsl_pci.c b/arch/powerpc/sysdev/fsl_pci.c
>> index ccfb50d..26039e3 100644
>> --- a/arch/powerpc/sysdev/fsl_pci.c
>> +++ b/arch/powerpc/sysdev/fsl_pci.c
>> @@ -27,6 +27,7 @@
>> #include <linux/log2.h>
>> #include <linux/slab.h>
>> #include <linux/uaccess.h>
>> +#include <linux/fsl/pci-common.h>
>>
>> #include <asm/io.h>
>> #include <asm/prom.h>
>> @@ -58,57 +59,8 @@ static void quirk_fsl_pcie_header(struct pci_dev *dev)
>> return;
>> }
>>
>> -static int fsl_indirect_read_config(struct pci_bus *, unsigned int,
>> - int, int, u32 *);
>> -
>> -static int fsl_pcie_check_link(struct pci_controller *hose)
>> -{
>> - u32 val = 0;
>> -
>> - if (hose->indirect_type & PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK) {
>> - if (hose->ops->read == fsl_indirect_read_config) {
>> - struct pci_bus bus;
>> - bus.number = hose->first_busno;
>> - bus.sysdata = hose;
>> - bus.ops = hose->ops;
>> - indirect_read_config(&bus, 0, PCIE_LTSSM, 4, &val);
>> - } else
>> - early_read_config_dword(hose, 0, 0, PCIE_LTSSM, &val);
>> - if (val < PCIE_LTSSM_L0)
>> - return 1;
>> - } else {
>> - struct ccsr_pci __iomem *pci = hose->private_data;
>> - /* for PCIe IP rev 3.0 or greater use CSR0 for link state */
>> - val = (in_be32(&pci->pex_csr0) & PEX_CSR0_LTSSM_MASK)
>> - >> PEX_CSR0_LTSSM_SHIFT;
>> - if (val != PEX_CSR0_LTSSM_L0)
>> - return 1;
>> - }
>> -
>> - return 0;
>> -}
>> -
>> -static int fsl_indirect_read_config(struct pci_bus *bus, unsigned int devfn,
>> - int offset, int len, u32 *val)
>> -{
>> - struct pci_controller *hose = pci_bus_to_host(bus);
>> -
>> - if (fsl_pcie_check_link(hose))
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
>> - else
>> - hose->indirect_type &= ~PPC_INDIRECT_TYPE_NO_PCIE_LINK;
>> -
>> - return indirect_read_config(bus, devfn, offset, len, val);
>> -}
>> -
>> #if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx)
>>
>> -static struct pci_ops fsl_indirect_pcie_ops =
>> -{
>> - .read = fsl_indirect_read_config,
>> - .write = indirect_write_config,
>> -};
>> -
>> #define MAX_PHYS_ADDR_BITS 40
>> static u64 pci64_dma_offset = 1ull << MAX_PHYS_ADDR_BITS;
>>
>> @@ -132,291 +84,6 @@ static int fsl_pci_dma_set_mask(struct device *dev, u64 dma_mask)
>> return 0;
>> }
>>
>> -static int setup_one_atmu(struct ccsr_pci __iomem *pci,
>> - unsigned int index, const struct resource *res,
>> - resource_size_t offset)
>> -{
>> - resource_size_t pci_addr = res->start - offset;
>> - resource_size_t phys_addr = res->start;
>> - resource_size_t size = resource_size(res);
>> - u32 flags = 0x80044000; /* enable & mem R/W */
>> - unsigned int i;
>> -
>> - pr_debug("PCI MEM resource start 0x%016llx, size 0x%016llx.\n",
>> - (u64)res->start, (u64)size);
>> -
>> - if (res->flags & IORESOURCE_PREFETCH)
>> - flags |= 0x10000000; /* enable relaxed ordering */
>> -
>> - for (i = 0; size > 0; i++) {
>> - unsigned int bits = min(ilog2(size),
>> - __ffs(pci_addr | phys_addr));
>> -
>> - if (index + i >= 5)
>> - return -1;
>> -
>> - out_be32(&pci->pow[index + i].potar, pci_addr >> 12);
>> - out_be32(&pci->pow[index + i].potear, (u64)pci_addr >> 44);
>> - out_be32(&pci->pow[index + i].powbar, phys_addr >> 12);
>> - out_be32(&pci->pow[index + i].powar, flags | (bits - 1));
>> -
>> - pci_addr += (resource_size_t)1U << bits;
>> - phys_addr += (resource_size_t)1U << bits;
>> - size -= (resource_size_t)1U << bits;
>> - }
>> -
>> - return i;
>> -}
>> -
>> -/* atmu setup for fsl pci/pcie controller */
>> -static void setup_pci_atmu(struct pci_controller *hose)
>> -{
>> - struct ccsr_pci __iomem *pci = hose->private_data;
>> - int i, j, n, mem_log, win_idx = 3, start_idx = 1, end_idx = 4;
>> - u64 mem, sz, paddr_hi = 0;
>> - u64 offset = 0, paddr_lo = ULLONG_MAX;
>> - u32 pcicsrbar = 0, pcicsrbar_sz;
>> - u32 piwar = PIWAR_EN | PIWAR_PF | PIWAR_TGI_LOCAL |
>> - PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP;
>> - const char *name = hose->dn->full_name;
>> - const u64 *reg;
>> - int len;
>> -
>> - if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) {
>> - if (in_be32(&pci->block_rev1) >= PCIE_IP_REV_2_2) {
>> - win_idx = 2;
>> - start_idx = 0;
>> - end_idx = 3;
>> - }
>> - }
>> -
>> - /* Disable all windows (except powar0 since it's ignored) */
>> - for(i = 1; i < 5; i++)
>> - out_be32(&pci->pow[i].powar, 0);
>> - for (i = start_idx; i < end_idx; i++)
>> - out_be32(&pci->piw[i].piwar, 0);
>> -
>> - /* Setup outbound MEM window */
>> - for(i = 0, j = 1; i < 3; i++) {
>> - if (!(hose->mem_resources[i].flags & IORESOURCE_MEM))
>> - continue;
>> -
>> - paddr_lo = min(paddr_lo, (u64)hose->mem_resources[i].start);
>> - paddr_hi = max(paddr_hi, (u64)hose->mem_resources[i].end);
>> -
>> - /* We assume all memory resources have the same offset */
>> - offset = hose->mem_offset[i];
>> - n = setup_one_atmu(pci, j, &hose->mem_resources[i], offset);
>> -
>> - if (n < 0 || j >= 5) {
>> - pr_err("Ran out of outbound PCI ATMUs for resource %d!\n", i);
>> - hose->mem_resources[i].flags |= IORESOURCE_DISABLED;
>> - } else
>> - j += n;
>> - }
>> -
>> - /* Setup outbound IO window */
>> - if (hose->io_resource.flags & IORESOURCE_IO) {
>> - if (j >= 5) {
>> - pr_err("Ran out of outbound PCI ATMUs for IO resource\n");
>> - } else {
>> - pr_debug("PCI IO resource start 0x%016llx, size 0x%016llx, "
>> - "phy base 0x%016llx.\n",
>> - (u64)hose->io_resource.start,
>> - (u64)resource_size(&hose->io_resource),
>> - (u64)hose->io_base_phys);
>> - out_be32(&pci->pow[j].potar, (hose->io_resource.start >> 12));
>> - out_be32(&pci->pow[j].potear, 0);
>> - out_be32(&pci->pow[j].powbar, (hose->io_base_phys >> 12));
>> - /* Enable, IO R/W */
>> - out_be32(&pci->pow[j].powar, 0x80088000
>> - | (ilog2(hose->io_resource.end
>> - - hose->io_resource.start + 1) - 1));
>> - }
>> - }
>> -
>> - /* convert to pci address space */
>> - paddr_hi -= offset;
>> - paddr_lo -= offset;
>> -
>> - if (paddr_hi == paddr_lo) {
>> - pr_err("%s: No outbound window space\n", name);
>> - return;
>> - }
>> -
>> - if (paddr_lo == 0) {
>> - pr_err("%s: No space for inbound window\n", name);
>> - return;
>> - }
>> -
>> - /* setup PCSRBAR/PEXCSRBAR */
>> - early_write_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, 0xffffffff);
>> - early_read_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, &pcicsrbar_sz);
>> - pcicsrbar_sz = ~pcicsrbar_sz + 1;
>> -
>> - if (paddr_hi < (0x100000000ull - pcicsrbar_sz) ||
>> - (paddr_lo > 0x100000000ull))
>> - pcicsrbar = 0x100000000ull - pcicsrbar_sz;
>> - else
>> - pcicsrbar = (paddr_lo - pcicsrbar_sz) & -pcicsrbar_sz;
>> - early_write_config_dword(hose, 0, 0, PCI_BASE_ADDRESS_0, pcicsrbar);
>> -
>> - paddr_lo = min(paddr_lo, (u64)pcicsrbar);
>> -
>> - pr_info("%s: PCICSRBAR @ 0x%x\n", name, pcicsrbar);
>> -
>> - /* Setup inbound mem window */
>> - mem = memblock_end_of_DRAM();
>> -
>> - /*
>> - * The msi-address-64 property, if it exists, indicates the physical
>> - * address of the MSIIR register. Normally, this register is located
>> - * inside CCSR, so the ATMU that covers all of CCSR is used. But if
>> - * this property exists, then we normally need to create a new ATMU
>> - * for it. For now, however, we cheat. The only entity that creates
>> - * this property is the Freescale hypervisor, and the address is
>> - * specified in the partition configuration. Typically, the address
>> - * is located in the page immediately after the end of DDR. If so, we
>> - * can avoid allocating a new ATMU by extending the DDR ATMU by one
>> - * page.
>> - */
>> - reg = of_get_property(hose->dn, "msi-address-64", &len);
>> - if (reg && (len == sizeof(u64))) {
>> - u64 address = be64_to_cpup(reg);
>> -
>> - if ((address >= mem) && (address < (mem + PAGE_SIZE))) {
>> - pr_info("%s: extending DDR ATMU to cover MSIIR", name);
>> - mem += PAGE_SIZE;
>> - } else {
>> - /* TODO: Create a new ATMU for MSIIR */
>> - pr_warn("%s: msi-address-64 address of %llx is "
>> - "unsupported\n", name, address);
>> - }
>> - }
>> -
>> - sz = min(mem, paddr_lo);
>> - mem_log = ilog2(sz);
>> -
>> - /* PCIe can overmap inbound & outbound since RX & TX are separated */
>> - if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) {
>> - /* Size window to exact size if power-of-two or one size up */
>> - if ((1ull << mem_log) != mem) {
>> - mem_log++;
>> - if ((1ull << mem_log) > mem)
>> - pr_info("%s: Setting PCI inbound window "
>> - "greater than memory size\n", name);
>> - }
>> -
>> - piwar |= ((mem_log - 1) & PIWAR_SZ_MASK);
>> -
>> - /* Setup inbound memory window */
>> - out_be32(&pci->piw[win_idx].pitar, 0x00000000);
>> - out_be32(&pci->piw[win_idx].piwbar, 0x00000000);
>> - out_be32(&pci->piw[win_idx].piwar, piwar);
>> - win_idx--;
>> -
>> - hose->dma_window_base_cur = 0x00000000;
>> - hose->dma_window_size = (resource_size_t)sz;
>> -
>> - /*
>> - * if we have >4G of memory setup second PCI inbound window to
>> - * let devices that are 64-bit address capable to work w/o
>> - * SWIOTLB and access the full range of memory
>> - */
>> - if (sz != mem) {
>> - mem_log = ilog2(mem);
>> -
>> - /* Size window up if we dont fit in exact power-of-2 */
>> - if ((1ull << mem_log) != mem)
>> - mem_log++;
>> -
>> - piwar = (piwar & ~PIWAR_SZ_MASK) | (mem_log - 1);
>> -
>> - /* Setup inbound memory window */
>> - out_be32(&pci->piw[win_idx].pitar, 0x00000000);
>> - out_be32(&pci->piw[win_idx].piwbear,
>> - pci64_dma_offset >> 44);
>> - out_be32(&pci->piw[win_idx].piwbar,
>> - pci64_dma_offset >> 12);
>> - out_be32(&pci->piw[win_idx].piwar, piwar);
>> -
>> - /*
>> - * install our own dma_set_mask handler to fixup dma_ops
>> - * and dma_offset
>> - */
>> - ppc_md.dma_set_mask = fsl_pci_dma_set_mask;
>> -
>> - pr_info("%s: Setup 64-bit PCI DMA window\n", name);
>> - }
>> - } else {
>> - u64 paddr = 0;
>> -
>> - /* Setup inbound memory window */
>> - out_be32(&pci->piw[win_idx].pitar, paddr >> 12);
>> - out_be32(&pci->piw[win_idx].piwbar, paddr >> 12);
>> - out_be32(&pci->piw[win_idx].piwar, (piwar | (mem_log - 1)));
>> - win_idx--;
>> -
>> - paddr += 1ull << mem_log;
>> - sz -= 1ull << mem_log;
>> -
>> - if (sz) {
>> - mem_log = ilog2(sz);
>> - piwar |= (mem_log - 1);
>> -
>> - out_be32(&pci->piw[win_idx].pitar, paddr >> 12);
>> - out_be32(&pci->piw[win_idx].piwbar, paddr >> 12);
>> - out_be32(&pci->piw[win_idx].piwar, piwar);
>> - win_idx--;
>> -
>> - paddr += 1ull << mem_log;
>> - }
>> -
>> - hose->dma_window_base_cur = 0x00000000;
>> - hose->dma_window_size = (resource_size_t)paddr;
>> - }
>> -
>> - if (hose->dma_window_size < mem) {
>> -#ifdef CONFIG_SWIOTLB
>> - ppc_swiotlb_enable = 1;
>> -#else
>> - pr_err("%s: ERROR: Memory size exceeds PCI ATMU ability to "
>> - "map - enable CONFIG_SWIOTLB to avoid dma errors.\n",
>> - name);
>> -#endif
>> - /* adjusting outbound windows could reclaim space in mem map */
>> - if (paddr_hi < 0xffffffffull)
>> - pr_warning("%s: WARNING: Outbound window cfg leaves "
>> - "gaps in memory map. Adjusting the memory map "
>> - "could reduce unnecessary bounce buffering.\n",
>> - name);
>> -
>> - pr_info("%s: DMA window size is 0x%llx\n", name,
>> - (u64)hose->dma_window_size);
>> - }
>> -}
>> -
>> -static void __init setup_pci_cmd(struct pci_controller *hose)
>> -{
>> - u16 cmd;
>> - int cap_x;
>> -
>> - early_read_config_word(hose, 0, 0, PCI_COMMAND, &cmd);
>> - cmd |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY
>> - | PCI_COMMAND_IO;
>> - early_write_config_word(hose, 0, 0, PCI_COMMAND, cmd);
>> -
>> - cap_x = early_find_capability(hose, 0, 0, PCI_CAP_ID_PCIX);
>> - if (cap_x) {
>> - int pci_x_cmd = cap_x + PCI_X_CMD;
>> - cmd = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ
>> - | PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E;
>> - early_write_config_word(hose, 0, 0, pci_x_cmd, cmd);
>> - } else {
>> - early_write_config_byte(hose, 0, 0, PCI_LATENCY_TIMER, 0x80);
>> - }
>> -}
>> -
>> void fsl_pcibios_fixup_bus(struct pci_bus *bus)
>> {
>> struct pci_controller *hose = pci_bus_to_host(bus);
>> @@ -454,112 +121,6 @@ void fsl_pcibios_fixup_bus(struct pci_bus *bus)
>> }
>> }
>>
>> -int __init fsl_add_bridge(struct platform_device *pdev, int is_primary)
>> -{
>> - int len;
>> - struct pci_controller *hose;
>> - struct resource rsrc;
>> - const int *bus_range;
>> - u8 hdr_type, progif;
>> - struct device_node *dev;
>> - struct ccsr_pci __iomem *pci;
>> -
>> - dev = pdev->dev.of_node;
>> -
>> - if (!of_device_is_available(dev)) {
>> - pr_warning("%s: disabled\n", dev->full_name);
>> - return -ENODEV;
>> - }
>> -
>> - pr_debug("Adding PCI host bridge %s\n", dev->full_name);
>> -
>> - /* Fetch host bridge registers address */
>> - if (of_address_to_resource(dev, 0, &rsrc)) {
>> - printk(KERN_WARNING "Can't get pci register base!");
>> - return -ENOMEM;
>> - }
>> -
>> - /* Get bus range if any */
>> - bus_range = of_get_property(dev, "bus-range", &len);
>> - if (bus_range == NULL || len < 2 * sizeof(int))
>> - printk(KERN_WARNING "Can't get bus-range for %s, assume"
>> - " bus 0\n", dev->full_name);
>> -
>> - pci_add_flags(PCI_REASSIGN_ALL_BUS);
>> - hose = pcibios_alloc_controller(dev);
>> - if (!hose)
>> - return -ENOMEM;
>> -
>> - /* set platform device as the parent */
>> - hose->parent = &pdev->dev;
>> - hose->first_busno = bus_range ? bus_range[0] : 0x0;
>> - hose->last_busno = bus_range ? bus_range[1] : 0xff;
>> -
>> - pr_debug("PCI memory map start 0x%016llx, size 0x%016llx\n",
>> - (u64)rsrc.start, (u64)resource_size(&rsrc));
>> -
>> - pci = hose->private_data = ioremap(rsrc.start, resource_size(&rsrc));
>> - if (!hose->private_data)
>> - goto no_bridge;
>> -
>> - setup_indirect_pci(hose, rsrc.start, rsrc.start + 0x4,
>> - PPC_INDIRECT_TYPE_BIG_ENDIAN);
>> -
>> - if (in_be32(&pci->block_rev1) < PCIE_IP_REV_3_0)
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK;
>> -
>> - if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) {
>> - /* use fsl_indirect_read_config for PCIe */
>> - hose->ops = &fsl_indirect_pcie_ops;
>> - /* For PCIE read HEADER_TYPE to identify controler mode */
>> - early_read_config_byte(hose, 0, 0, PCI_HEADER_TYPE, &hdr_type);
>> - if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE)
>> - goto no_bridge;
>> -
>> - } else {
>> - /* For PCI read PROG to identify controller mode */
>> - early_read_config_byte(hose, 0, 0, PCI_CLASS_PROG, &progif);
>> - if ((progif & 1) == 1)
>> - goto no_bridge;
>> - }
>> -
>> - setup_pci_cmd(hose);
>> -
>> - /* check PCI express link status */
>> - if (early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP)) {
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_EXT_REG |
>> - PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS;
>> - if (fsl_pcie_check_link(hose))
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
>> - }
>> -
>> - printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx. "
>> - "Firmware bus number: %d->%d\n",
>> - (unsigned long long)rsrc.start, hose->first_busno,
>> - hose->last_busno);
>> -
>> - pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
>> - hose, hose->cfg_addr, hose->cfg_data);
>> -
>> - /* Interpret the "ranges" property */
>> - /* This also maps the I/O region and sets isa_io/mem_base */
>> - pci_process_bridge_OF_ranges(hose, dev, is_primary);
>> -
>> - /* Setup PEX window registers */
>> - setup_pci_atmu(hose);
>> -
>> - return 0;
>> -
>> -no_bridge:
>> - iounmap(hose->private_data);
>> - /* unmap cfg_data & cfg_addr separately if not on same page */
>> - if (((unsigned long)hose->cfg_data & PAGE_MASK) !=
>> - ((unsigned long)hose->cfg_addr & PAGE_MASK))
>> - iounmap(hose->cfg_data);
>> - iounmap(hose->cfg_addr);
>> - pcibios_free_controller(hose);
>> - return -ENODEV;
>> -}
>> #endif /* CONFIG_FSL_SOC_BOOKE || CONFIG_PPC_86xx */
>>
>> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID, quirk_fsl_pcie_header);
>> @@ -1029,26 +590,6 @@ int fsl_pci_mcheck_exception(struct pt_regs *regs)
>> #endif
>>
>> #if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx)
>> -static const struct of_device_id pci_ids[] = {
>> - { .compatible = "fsl,mpc8540-pci", },
>> - { .compatible = "fsl,mpc8548-pcie", },
>> - { .compatible = "fsl,mpc8610-pci", },
>> - { .compatible = "fsl,mpc8641-pcie", },
>> - { .compatible = "fsl,qoriq-pcie-v2.1", },
>> - { .compatible = "fsl,qoriq-pcie-v2.2", },
>> - { .compatible = "fsl,qoriq-pcie-v2.3", },
>> - { .compatible = "fsl,qoriq-pcie-v2.4", },
>> - { .compatible = "fsl,qoriq-pcie-v3.0", },
>> -
>> - /*
>> - * The following entries are for compatibility with older device
>> - * trees.
>> - */
>> - { .compatible = "fsl,p1022-pcie", },
>> - { .compatible = "fsl,p4080-pcie", },
>> -
>> - {},
>> -};
>>
>> struct device_node *fsl_pci_primary;
>>
>> @@ -1083,64 +624,4 @@ void fsl_pci_assign_primary(void)
>> }
>> }
>> }
>> -
>> -static int fsl_pci_probe(struct platform_device *pdev)
>> -{
>> - int ret;
>> - struct device_node *node;
>> -
>> - node = pdev->dev.of_node;
>> - ret = fsl_add_bridge(pdev, fsl_pci_primary == node);
>> -
>> - mpc85xx_pci_err_probe(pdev);
>> -
>> - return 0;
>> -}
>> -
>> -#ifdef CONFIG_PM
>> -static int fsl_pci_resume(struct device *dev)
>> -{
>> - struct pci_controller *hose;
>> - struct resource pci_rsrc;
>> -
>> - hose = pci_find_hose_for_OF_device(dev->of_node);
>> - if (!hose)
>> - return -ENODEV;
>> -
>> - if (of_address_to_resource(dev->of_node, 0, &pci_rsrc)) {
>> - dev_err(dev, "Get pci register base failed.");
>> - return -ENODEV;
>> - }
>> -
>> - setup_pci_atmu(hose);
>> -
>> - return 0;
>> -}
>> -
>> -static const struct dev_pm_ops pci_pm_ops = {
>> - .resume = fsl_pci_resume,
>> -};
>> -
>> -#define PCI_PM_OPS (&pci_pm_ops)
>> -
>> -#else
>> -
>> -#define PCI_PM_OPS NULL
>> -
>> -#endif
>> -
>> -static struct platform_driver fsl_pci_driver = {
>> - .driver = {
>> - .name = "fsl-pci",
>> - .pm = PCI_PM_OPS,
>> - .of_match_table = pci_ids,
>> - },
>> - .probe = fsl_pci_probe,
>> -};
>> -
>> -static int __init fsl_pci_init(void)
>> -{
>> - return platform_driver_register(&fsl_pci_driver);
>> -}
>> -arch_initcall(fsl_pci_init);
>> #endif
>> diff --git a/arch/powerpc/sysdev/fsl_pci.h b/arch/powerpc/sysdev/fsl_pci.h
>> index 8d455df..ce77aad 100644
>> --- a/arch/powerpc/sysdev/fsl_pci.h
>> +++ b/arch/powerpc/sysdev/fsl_pci.h
>> @@ -21,95 +21,6 @@ struct platform_device;
>> #define PCI_FSL_BRR1 0xbf8
>> #define PCI_FSL_BRR1_VER 0xffff
>>
>> -#define PCIE_LTSSM 0x0404 /* PCIE Link Training and Status */
>> -#define PCIE_LTSSM_L0 0x16 /* L0 state */
>> -#define PCIE_IP_REV_2_2 0x02080202 /* PCIE IP block version Rev2.2 */
>> -#define PCIE_IP_REV_3_0 0x02080300 /* PCIE IP block version Rev3.0 */
>> -#define PIWAR_EN 0x80000000 /* Enable */
>> -#define PIWAR_PF 0x20000000 /* prefetch */
>> -#define PIWAR_TGI_LOCAL 0x00f00000 /* target - local memory */
>> -#define PIWAR_READ_SNOOP 0x00050000
>> -#define PIWAR_WRITE_SNOOP 0x00005000
>> -#define PIWAR_SZ_MASK 0x0000003f
>> -
>> -/* PCI/PCI Express outbound window reg */
>> -struct pci_outbound_window_regs {
>> - __be32 potar; /* 0x.0 - Outbound translation address register */
>> - __be32 potear; /* 0x.4 - Outbound translation extended address register */
>> - __be32 powbar; /* 0x.8 - Outbound window base address register */
>> - u8 res1[4];
>> - __be32 powar; /* 0x.10 - Outbound window attributes register */
>> - u8 res2[12];
>> -};
>> -
>> -/* PCI/PCI Express inbound window reg */
>> -struct pci_inbound_window_regs {
>> - __be32 pitar; /* 0x.0 - Inbound translation address register */
>> - u8 res1[4];
>> - __be32 piwbar; /* 0x.8 - Inbound window base address register */
>> - __be32 piwbear; /* 0x.c - Inbound window base extended address register */
>> - __be32 piwar; /* 0x.10 - Inbound window attributes register */
>> - u8 res2[12];
>> -};
>> -
>> -/* PCI/PCI Express IO block registers for 85xx/86xx */
>> -struct ccsr_pci {
>> - __be32 config_addr; /* 0x.000 - PCI/PCIE Configuration Address Register */
>> - __be32 config_data; /* 0x.004 - PCI/PCIE Configuration Data Register */
>> - __be32 int_ack; /* 0x.008 - PCI Interrupt Acknowledge Register */
>> - __be32 pex_otb_cpl_tor; /* 0x.00c - PCIE Outbound completion timeout register */
>> - __be32 pex_conf_tor; /* 0x.010 - PCIE configuration timeout register */
>> - __be32 pex_config; /* 0x.014 - PCIE CONFIG Register */
>> - __be32 pex_int_status; /* 0x.018 - PCIE interrupt status */
>> - u8 res2[4];
>> - __be32 pex_pme_mes_dr; /* 0x.020 - PCIE PME and message detect register */
>> - __be32 pex_pme_mes_disr; /* 0x.024 - PCIE PME and message disable register */
>> - __be32 pex_pme_mes_ier; /* 0x.028 - PCIE PME and message interrupt enable register */
>> - __be32 pex_pmcr; /* 0x.02c - PCIE power management command register */
>> - u8 res3[3016];
>> - __be32 block_rev1; /* 0x.bf8 - PCIE Block Revision register 1 */
>> - __be32 block_rev2; /* 0x.bfc - PCIE Block Revision register 2 */
>> -
>> -/* PCI/PCI Express outbound window 0-4
>> - * Window 0 is the default window and is the only window enabled upon reset.
>> - * The default outbound register set is used when a transaction misses
>> - * in all of the other outbound windows.
>> - */
>> - struct pci_outbound_window_regs pow[5];
>> - u8 res14[96];
>> - struct pci_inbound_window_regs pmit; /* 0xd00 - 0xd9c Inbound MSI */
>> - u8 res6[96];
>> -/* PCI/PCI Express inbound window 3-0
>> - * inbound window 1 supports only a 32-bit base address and does not
>> - * define an inbound window base extended address register.
>> - */
>> - struct pci_inbound_window_regs piw[4];
>> -
>> - __be32 pex_err_dr; /* 0x.e00 - PCI/PCIE error detect register */
>> - u8 res21[4];
>> - __be32 pex_err_en; /* 0x.e08 - PCI/PCIE error interrupt enable register */
>> - u8 res22[4];
>> - __be32 pex_err_disr; /* 0x.e10 - PCI/PCIE error disable register */
>> - u8 res23[12];
>> - __be32 pex_err_cap_stat; /* 0x.e20 - PCI/PCIE error capture status register */
>> - u8 res24[4];
>> - __be32 pex_err_cap_r0; /* 0x.e28 - PCIE error capture register 0 */
>> - __be32 pex_err_cap_r1; /* 0x.e2c - PCIE error capture register 0 */
>> - __be32 pex_err_cap_r2; /* 0x.e30 - PCIE error capture register 0 */
>> - __be32 pex_err_cap_r3; /* 0x.e34 - PCIE error capture register 0 */
>> - u8 res_e38[200];
>> - __be32 pdb_stat; /* 0x.f00 - PCIE Debug Status */
>> - u8 res_f04[16];
>> - __be32 pex_csr0; /* 0x.f14 - PEX Control/Status register 0*/
>> -#define PEX_CSR0_LTSSM_MASK 0xFC
>> -#define PEX_CSR0_LTSSM_SHIFT 2
>> -#define PEX_CSR0_LTSSM_L0 0x11
>> - __be32 pex_csr1; /* 0x.f18 - PEX Control/Status register 1*/
>> - u8 res_f1c[228];
>> -
>> -};
>> -
>> -extern int fsl_add_bridge(struct platform_device *pdev, int is_primary);
>> extern void fsl_pcibios_fixup_bus(struct pci_bus *bus);
>> extern int mpc83xx_add_bridge(struct device_node *dev);
>> u64 fsl_pci_immrbar_base(struct pci_controller *hose);
>> diff --git a/arch/powerpc/sysdev/fsl_pci.c b/drivers/pci/host/pci-fsl-common.c
>> similarity index 54%
>> copy from arch/powerpc/sysdev/fsl_pci.c
>> copy to drivers/pci/host/pci-fsl-common.c
>> index ccfb50d..69d338b 100644
>> --- a/arch/powerpc/sysdev/fsl_pci.c
>> +++ b/drivers/pci/host/pci-fsl-common.c
>> @@ -1,5 +1,5 @@
>> /*
>> - * MPC83xx/85xx/86xx PCI/PCIE support routing.
>> + * 85xx/86xx/LS PCI/PCIE support routing.
>> *
>> * Copyright 2007-2012 Freescale Semiconductor, Inc.
>> * Copyright 2008-2009 MontaVista Software, Inc.
>> @@ -8,9 +8,6 @@
>> * Recode: ZHANG WEI <wei.zhang at freescale.com>
>> * Rewrite the routing for Frescale PCI and PCI Express
>> * Roy Zang <tie-fei.zang at freescale.com>
>> - * MPC83xx PCI-Express support:
>> - * Tony Li <tony.li at freescale.com>
>> - * Anton Vorontsov <avorontsov at ru.mvista.com>
>> *
>> * This program is free software; you can redistribute it and/or modify it
>> * under the terms of the GNU General Public License as published by the
>> @@ -38,29 +35,6 @@
>> #include <sysdev/fsl_soc.h>
>> #include <sysdev/fsl_pci.h>
>>
>> -static int fsl_pcie_bus_fixup, is_mpc83xx_pci;
>> -
>> -static void quirk_fsl_pcie_header(struct pci_dev *dev)
>> -{
>> - u8 hdr_type;
>> -
>> - /* if we aren't a PCIe don't bother */
>> - if (!pci_find_capability(dev, PCI_CAP_ID_EXP))
>> - return;
>> -
>> - /* if we aren't in host mode don't bother */
>> - pci_read_config_byte(dev, PCI_HEADER_TYPE, &hdr_type);
>> - if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE)
>> - return;
>> -
>> - dev->class = PCI_CLASS_BRIDGE_PCI << 8;
>> - fsl_pcie_bus_fixup = 1;
>> - return;
>> -}
>> -
>> -static int fsl_indirect_read_config(struct pci_bus *, unsigned int,
>> - int, int, u32 *);
>> -
>> static int fsl_pcie_check_link(struct pci_controller *hose)
>> {
>> u32 val = 0;
>> @@ -109,29 +83,6 @@ static struct pci_ops fsl_indirect_pcie_ops =
>> .write = indirect_write_config,
>> };
>>
>> -#define MAX_PHYS_ADDR_BITS 40
>> -static u64 pci64_dma_offset = 1ull << MAX_PHYS_ADDR_BITS;
>> -
>> -static int fsl_pci_dma_set_mask(struct device *dev, u64 dma_mask)
>> -{
>> - if (!dev->dma_mask || !dma_supported(dev, dma_mask))
>> - return -EIO;
>> -
>> - /*
>> - * Fixup PCI devices that are able to DMA to above the physical
>> - * address width of the SoC such that we can address any internal
>> - * SoC address from across PCI if needed
>> - */
>> - if ((dev->bus == &pci_bus_type) &&
>> - dma_mask >= DMA_BIT_MASK(MAX_PHYS_ADDR_BITS)) {
>> - set_dma_ops(dev, &dma_direct_ops);
>> - set_dma_offset(dev, pci64_dma_offset);
>> - }
>> -
>> - *dev->dma_mask = dma_mask;
>> - return 0;
>> -}
>> -
>> static int setup_one_atmu(struct ccsr_pci __iomem *pci,
>> unsigned int index, const struct resource *res,
>> resource_size_t offset)
>> @@ -417,43 +368,6 @@ static void __init setup_pci_cmd(struct pci_controller *hose)
>> }
>> }
>>
>> -void fsl_pcibios_fixup_bus(struct pci_bus *bus)
>> -{
>> - struct pci_controller *hose = pci_bus_to_host(bus);
>> - int i, is_pcie = 0, no_link;
>> -
>> - /* The root complex bridge comes up with bogus resources,
>> - * we copy the PHB ones in.
>> - *
>> - * With the current generic PCI code, the PHB bus no longer
>> - * has bus->resource[0..4] set, so things are a bit more
>> - * tricky.
>> - */
>> -
>> - if (fsl_pcie_bus_fixup)
>> - is_pcie = early_find_capability(hose, 0, 0, PCI_CAP_ID_EXP);
>> - no_link = !!(hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK);
>> -
>> - if (bus->parent == hose->bus && (is_pcie || no_link)) {
>> - for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; ++i) {
>> - struct resource *res = bus->resource[i];
>> - struct resource *par;
>> -
>> - if (!res)
>> - continue;
>> - if (i == 0)
>> - par = &hose->io_resource;
>> - else if (i < 4)
>> - par = &hose->mem_resources[i-1];
>> - else par = NULL;
>> -
>> - res->start = par ? par->start : 0;
>> - res->end = par ? par->end : 0;
>> - res->flags = par ? par->flags : 0;
>> - }
>> - }
>> -}
>> -
>> int __init fsl_add_bridge(struct platform_device *pdev, int is_primary)
>> {
>> int len;
>> @@ -560,475 +474,7 @@ no_bridge:
>> pcibios_free_controller(hose);
>> return -ENODEV;
>> }
>> -#endif /* CONFIG_FSL_SOC_BOOKE || CONFIG_PPC_86xx */
>> -
>> -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID, quirk_fsl_pcie_header);
>> -
>> -#if defined(CONFIG_PPC_83xx) || defined(CONFIG_PPC_MPC512x)
>> -struct mpc83xx_pcie_priv {
>> - void __iomem *cfg_type0;
>> - void __iomem *cfg_type1;
>> - u32 dev_base;
>> -};
>> -
>> -struct pex_inbound_window {
>> - u32 ar;
>> - u32 tar;
>> - u32 barl;
>> - u32 barh;
>> -};
>> -
>> -/*
>> - * With the convention of u-boot, the PCIE outbound window 0 serves
>> - * as configuration transactions outbound.
>> - */
>> -#define PEX_OUTWIN0_BAR 0xCA4
>> -#define PEX_OUTWIN0_TAL 0xCA8
>> -#define PEX_OUTWIN0_TAH 0xCAC
>> -#define PEX_RC_INWIN_BASE 0xE60
>> -#define PEX_RCIWARn_EN 0x1
>> -
>> -static int mpc83xx_pcie_exclude_device(struct pci_bus *bus, unsigned int devfn)
>> -{
>> - struct pci_controller *hose = pci_bus_to_host(bus);
>> -
>> - if (hose->indirect_type & PPC_INDIRECT_TYPE_NO_PCIE_LINK)
>> - return PCIBIOS_DEVICE_NOT_FOUND;
>> - /*
>> - * Workaround for the HW bug: for Type 0 configure transactions the
>> - * PCI-E controller does not check the device number bits and just
>> - * assumes that the device number bits are 0.
>> - */
>> - if (bus->number == hose->first_busno ||
>> - bus->primary == hose->first_busno) {
>> - if (devfn & 0xf8)
>> - return PCIBIOS_DEVICE_NOT_FOUND;
>> - }
>> -
>> - if (ppc_md.pci_exclude_device) {
>> - if (ppc_md.pci_exclude_device(hose, bus->number, devfn))
>> - return PCIBIOS_DEVICE_NOT_FOUND;
>> - }
>> -
>> - return PCIBIOS_SUCCESSFUL;
>> -}
>> -
>> -static void __iomem *mpc83xx_pcie_remap_cfg(struct pci_bus *bus,
>> - unsigned int devfn, int offset)
>> -{
>> - struct pci_controller *hose = pci_bus_to_host(bus);
>> - struct mpc83xx_pcie_priv *pcie = hose->dn->data;
>> - u32 dev_base = bus->number << 24 | devfn << 16;
>> - int ret;
>> -
>> - ret = mpc83xx_pcie_exclude_device(bus, devfn);
>> - if (ret)
>> - return NULL;
>> -
>> - offset &= 0xfff;
>> -
>> - /* Type 0 */
>> - if (bus->number == hose->first_busno)
>> - return pcie->cfg_type0 + offset;
>> -
>> - if (pcie->dev_base == dev_base)
>> - goto mapped;
>> -
>> - out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAL, dev_base);
>> -
>> - pcie->dev_base = dev_base;
>> -mapped:
>> - return pcie->cfg_type1 + offset;
>> -}
>> -
>> -static int mpc83xx_pcie_read_config(struct pci_bus *bus, unsigned int devfn,
>> - int offset, int len, u32 *val)
>> -{
>> - void __iomem *cfg_addr;
>> -
>> - cfg_addr = mpc83xx_pcie_remap_cfg(bus, devfn, offset);
>> - if (!cfg_addr)
>> - return PCIBIOS_DEVICE_NOT_FOUND;
>> -
>> - switch (len) {
>> - case 1:
>> - *val = in_8(cfg_addr);
>> - break;
>> - case 2:
>> - *val = in_le16(cfg_addr);
>> - break;
>> - default:
>> - *val = in_le32(cfg_addr);
>> - break;
>> - }
>> -
>> - return PCIBIOS_SUCCESSFUL;
>> -}
>> -
>> -static int mpc83xx_pcie_write_config(struct pci_bus *bus, unsigned int devfn,
>> - int offset, int len, u32 val)
>> -{
>> - struct pci_controller *hose = pci_bus_to_host(bus);
>> - void __iomem *cfg_addr;
>> -
>> - cfg_addr = mpc83xx_pcie_remap_cfg(bus, devfn, offset);
>> - if (!cfg_addr)
>> - return PCIBIOS_DEVICE_NOT_FOUND;
>> -
>> - /* PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS */
>> - if (offset == PCI_PRIMARY_BUS && bus->number == hose->first_busno)
>> - val &= 0xffffff00;
>> -
>> - switch (len) {
>> - case 1:
>> - out_8(cfg_addr, val);
>> - break;
>> - case 2:
>> - out_le16(cfg_addr, val);
>> - break;
>> - default:
>> - out_le32(cfg_addr, val);
>> - break;
>> - }
>> -
>> - return PCIBIOS_SUCCESSFUL;
>> -}
>> -
>> -static struct pci_ops mpc83xx_pcie_ops = {
>> - .read = mpc83xx_pcie_read_config,
>> - .write = mpc83xx_pcie_write_config,
>> -};
>> -
>> -static int __init mpc83xx_pcie_setup(struct pci_controller *hose,
>> - struct resource *reg)
>> -{
>> - struct mpc83xx_pcie_priv *pcie;
>> - u32 cfg_bar;
>> - int ret = -ENOMEM;
>> -
>> - pcie = zalloc_maybe_bootmem(sizeof(*pcie), GFP_KERNEL);
>> - if (!pcie)
>> - return ret;
>> -
>> - pcie->cfg_type0 = ioremap(reg->start, resource_size(reg));
>> - if (!pcie->cfg_type0)
>> - goto err0;
>> -
>> - cfg_bar = in_le32(pcie->cfg_type0 + PEX_OUTWIN0_BAR);
>> - if (!cfg_bar) {
>> - /* PCI-E isn't configured. */
>> - ret = -ENODEV;
>> - goto err1;
>> - }
>> -
>> - pcie->cfg_type1 = ioremap(cfg_bar, 0x1000);
>> - if (!pcie->cfg_type1)
>> - goto err1;
>> -
>> - WARN_ON(hose->dn->data);
>> - hose->dn->data = pcie;
>> - hose->ops = &mpc83xx_pcie_ops;
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_FSL_CFG_REG_LINK;
>> -
>> - out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAH, 0);
>> - out_le32(pcie->cfg_type0 + PEX_OUTWIN0_TAL, 0);
>> -
>> - if (fsl_pcie_check_link(hose))
>> - hose->indirect_type |= PPC_INDIRECT_TYPE_NO_PCIE_LINK;
>> -
>> - return 0;
>> -err1:
>> - iounmap(pcie->cfg_type0);
>> -err0:
>> - kfree(pcie);
>> - return ret;
>> -
>> -}
>> -
>> -int __init mpc83xx_add_bridge(struct device_node *dev)
>> -{
>> - int ret;
>> - int len;
>> - struct pci_controller *hose;
>> - struct resource rsrc_reg;
>> - struct resource rsrc_cfg;
>> - const int *bus_range;
>> - int primary;
>> -
>> - is_mpc83xx_pci = 1;
>> -
>> - if (!of_device_is_available(dev)) {
>> - pr_warning("%s: disabled by the firmware.\n",
>> - dev->full_name);
>> - return -ENODEV;
>> - }
>> - pr_debug("Adding PCI host bridge %s\n", dev->full_name);
>> -
>> - /* Fetch host bridge registers address */
>> - if (of_address_to_resource(dev, 0, &rsrc_reg)) {
>> - printk(KERN_WARNING "Can't get pci register base!\n");
>> - return -ENOMEM;
>> - }
>> -
>> - memset(&rsrc_cfg, 0, sizeof(rsrc_cfg));
>> -
>> - if (of_address_to_resource(dev, 1, &rsrc_cfg)) {
>> - printk(KERN_WARNING
>> - "No pci config register base in dev tree, "
>> - "using default\n");
>> - /*
>> - * MPC83xx supports up to two host controllers
>> - * one at 0x8500 has config space registers at 0x8300
>> - * one at 0x8600 has config space registers at 0x8380
>> - */
>> - if ((rsrc_reg.start & 0xfffff) == 0x8500)
>> - rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8300;
>> - else if ((rsrc_reg.start & 0xfffff) == 0x8600)
>> - rsrc_cfg.start = (rsrc_reg.start & 0xfff00000) + 0x8380;
>> - }
>> - /*
>> - * Controller at offset 0x8500 is primary
>> - */
>> - if ((rsrc_reg.start & 0xfffff) == 0x8500)
>> - primary = 1;
>> - else
>> - primary = 0;
>> -
>> - /* Get bus range if any */
>> - bus_range = of_get_property(dev, "bus-range", &len);
>> - if (bus_range == NULL || len < 2 * sizeof(int)) {
>> - printk(KERN_WARNING "Can't get bus-range for %s, assume"
>> - " bus 0\n", dev->full_name);
>> - }
>> -
>> - pci_add_flags(PCI_REASSIGN_ALL_BUS);
>> - hose = pcibios_alloc_controller(dev);
>> - if (!hose)
>> - return -ENOMEM;
>> -
>> - hose->first_busno = bus_range ? bus_range[0] : 0;
>> - hose->last_busno = bus_range ? bus_range[1] : 0xff;
>> -
>> - if (of_device_is_compatible(dev, "fsl,mpc8314-pcie")) {
>> - ret = mpc83xx_pcie_setup(hose, &rsrc_reg);
>> - if (ret)
>> - goto err0;
>> - } else {
>> - setup_indirect_pci(hose, rsrc_cfg.start,
>> - rsrc_cfg.start + 4, 0);
>> - }
>> -
>> - printk(KERN_INFO "Found FSL PCI host bridge at 0x%016llx. "
>> - "Firmware bus number: %d->%d\n",
>> - (unsigned long long)rsrc_reg.start, hose->first_busno,
>> - hose->last_busno);
>> -
>> - pr_debug(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
>> - hose, hose->cfg_addr, hose->cfg_data);
>> -
>> - /* Interpret the "ranges" property */
>> - /* This also maps the I/O region and sets isa_io/mem_base */
>> - pci_process_bridge_OF_ranges(hose, dev, primary);
>> -
>> - return 0;
>> -err0:
>> - pcibios_free_controller(hose);
>> - return ret;
>> -}
>> -#endif /* CONFIG_PPC_83xx */
>> -
>> -u64 fsl_pci_immrbar_base(struct pci_controller *hose)
>> -{
>> -#ifdef CONFIG_PPC_83xx
>> - if (is_mpc83xx_pci) {
>> - struct mpc83xx_pcie_priv *pcie = hose->dn->data;
>> - struct pex_inbound_window *in;
>> - int i;
>> -
>> - /* Walk the Root Complex Inbound windows to match IMMR base */
>> - in = pcie->cfg_type0 + PEX_RC_INWIN_BASE;
>> - for (i = 0; i < 4; i++) {
>> - /* not enabled, skip */
>> - if (!in_le32(&in[i].ar) & PEX_RCIWARn_EN)
>> - continue;
>> -
>> - if (get_immrbase() == in_le32(&in[i].tar))
>> - return (u64)in_le32(&in[i].barh) << 32 |
>> - in_le32(&in[i].barl);
>> - }
>> -
>> - printk(KERN_WARNING "could not find PCI BAR matching IMMR\n");
>> - }
>> -#endif
>> -
>> -#if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx)
>> - if (!is_mpc83xx_pci) {
>> - u32 base;
>> -
>> - pci_bus_read_config_dword(hose->bus,
>> - PCI_DEVFN(0, 0), PCI_BASE_ADDRESS_0, &base);
>> - return base;
>> - }
>> -#endif
>> -
>> - return 0;
>> -}
>>
>> -#ifdef CONFIG_E500
>> -static int mcheck_handle_load(struct pt_regs *regs, u32 inst)
>> -{
>> - unsigned int rd, ra, rb, d;
>> -
>> - rd = get_rt(inst);
>> - ra = get_ra(inst);
>> - rb = get_rb(inst);
>> - d = get_d(inst);
>> -
>> - switch (get_op(inst)) {
>> - case 31:
>> - switch (get_xop(inst)) {
>> - case OP_31_XOP_LWZX:
>> - case OP_31_XOP_LWBRX:
>> - regs->gpr[rd] = 0xffffffff;
>> - break;
>> -
>> - case OP_31_XOP_LWZUX:
>> - regs->gpr[rd] = 0xffffffff;
>> - regs->gpr[ra] += regs->gpr[rb];
>> - break;
>> -
>> - case OP_31_XOP_LBZX:
>> - regs->gpr[rd] = 0xff;
>> - break;
>> -
>> - case OP_31_XOP_LBZUX:
>> - regs->gpr[rd] = 0xff;
>> - regs->gpr[ra] += regs->gpr[rb];
>> - break;
>> -
>> - case OP_31_XOP_LHZX:
>> - case OP_31_XOP_LHBRX:
>> - regs->gpr[rd] = 0xffff;
>> - break;
>> -
>> - case OP_31_XOP_LHZUX:
>> - regs->gpr[rd] = 0xffff;
>> - regs->gpr[ra] += regs->gpr[rb];
>> - break;
>> -
>> - case OP_31_XOP_LHAX:
>> - regs->gpr[rd] = ~0UL;
>> - break;
>> -
>> - case OP_31_XOP_LHAUX:
>> - regs->gpr[rd] = ~0UL;
>> - regs->gpr[ra] += regs->gpr[rb];
>> - break;
>> -
>> - default:
>> - return 0;
>> - }
>> - break;
>> -
>> - case OP_LWZ:
>> - regs->gpr[rd] = 0xffffffff;
>> - break;
>> -
>> - case OP_LWZU:
>> - regs->gpr[rd] = 0xffffffff;
>> - regs->gpr[ra] += (s16)d;
>> - break;
>> -
>> - case OP_LBZ:
>> - regs->gpr[rd] = 0xff;
>> - break;
>> -
>> - case OP_LBZU:
>> - regs->gpr[rd] = 0xff;
>> - regs->gpr[ra] += (s16)d;
>> - break;
>> -
>> - case OP_LHZ:
>> - regs->gpr[rd] = 0xffff;
>> - break;
>> -
>> - case OP_LHZU:
>> - regs->gpr[rd] = 0xffff;
>> - regs->gpr[ra] += (s16)d;
>> - break;
>> -
>> - case OP_LHA:
>> - regs->gpr[rd] = ~0UL;
>> - break;
>> -
>> - case OP_LHAU:
>> - regs->gpr[rd] = ~0UL;
>> - regs->gpr[ra] += (s16)d;
>> - break;
>> -
>> - default:
>> - return 0;
>> - }
>> -
>> - return 1;
>> -}
>> -
>> -static int is_in_pci_mem_space(phys_addr_t addr)
>> -{
>> - struct pci_controller *hose;
>> - struct resource *res;
>> - int i;
>> -
>> - list_for_each_entry(hose, &hose_list, list_node) {
>> - if (!(hose->indirect_type & PPC_INDIRECT_TYPE_EXT_REG))
>> - continue;
>> -
>> - for (i = 0; i < 3; i++) {
>> - res = &hose->mem_resources[i];
>> - if ((res->flags & IORESOURCE_MEM) &&
>> - addr >= res->start && addr <= res->end)
>> - return 1;
>> - }
>> - }
>> - return 0;
>> -}
>> -
>> -int fsl_pci_mcheck_exception(struct pt_regs *regs)
>> -{
>> - u32 inst;
>> - int ret;
>> - phys_addr_t addr = 0;
>> -
>> - /* Let KVM/QEMU deal with the exception */
>> - if (regs->msr & MSR_GS)
>> - return 0;
>> -
>> -#ifdef CONFIG_PHYS_64BIT
>> - addr = mfspr(SPRN_MCARU);
>> - addr <<= 32;
>> -#endif
>> - addr += mfspr(SPRN_MCAR);
>> -
>> - if (is_in_pci_mem_space(addr)) {
>> - if (user_mode(regs)) {
>> - pagefault_disable();
>> - ret = get_user(regs->nip, &inst);
>> - pagefault_enable();
>> - } else {
>> - ret = probe_kernel_address(regs->nip, inst);
>> - }
>> -
>> - if (mcheck_handle_load(regs, inst)) {
>> - regs->nip += 4;
>> - return 1;
>> - }
>> - }
>> -
>> - return 0;
>> -}
>> -#endif
>> -
>> -#if defined(CONFIG_FSL_SOC_BOOKE) || defined(CONFIG_PPC_86xx)
>> static const struct of_device_id pci_ids[] = {
>> { .compatible = "fsl,mpc8540-pci", },
>> { .compatible = "fsl,mpc8548-pcie", },
>> @@ -1050,40 +496,6 @@ static const struct of_device_id pci_ids[] = {
>> {},
>> };
>>
>> -struct device_node *fsl_pci_primary;
>> -
>> -void fsl_pci_assign_primary(void)
>> -{
>> - struct device_node *np;
>> -
>> - /* Callers can specify the primary bus using other means. */
>> - if (fsl_pci_primary)
>> - return;
>> -
>> - /* If a PCI host bridge contains an ISA node, it's primary. */
>> - np = of_find_node_by_type(NULL, "isa");
>> - while ((fsl_pci_primary = of_get_parent(np))) {
>> - of_node_put(np);
>> - np = fsl_pci_primary;
>> -
>> - if (of_match_node(pci_ids, np) && of_device_is_available(np))
>> - return;
>> - }
>> -
>> - /*
>> - * If there's no PCI host bridge with ISA, arbitrarily
>> - * designate one as primary. This can go away once
>> - * various bugs with primary-less systems are fixed.
>> - */
>> - for_each_matching_node(np, pci_ids) {
>> - if (of_device_is_available(np)) {
>> - fsl_pci_primary = np;
>> - of_node_put(np);
>> - return;
>> - }
>> - }
>> -}
>> -
>> static int fsl_pci_probe(struct platform_device *pdev)
>> {
>> int ret;
>> @@ -1143,4 +555,3 @@ static int __init fsl_pci_init(void)
>> return platform_driver_register(&fsl_pci_driver);
>> }
>> arch_initcall(fsl_pci_init);
>> -#endif
>> diff --git a/arch/powerpc/sysdev/fsl_pci.h b/include/linux/fsl/pci-common.h
>> similarity index 79%
>> copy from arch/powerpc/sysdev/fsl_pci.h
>> copy to include/linux/fsl/pci-common.h
>> index 8d455df..5e4f683 100644
>> --- a/arch/powerpc/sysdev/fsl_pci.h
>> +++ b/include/linux/fsl/pci-common.h
>> @@ -1,5 +1,5 @@
>> /*
>> - * MPC85xx/86xx PCI Express structure define
>> + * MPC85xx/86xx/LS PCI Express structure define
>> *
>> * Copyright 2007,2011 Freescale Semiconductor, Inc
>> *
>> @@ -11,15 +11,8 @@
>> */
>>
>> #ifdef __KERNEL__
>> -#ifndef __POWERPC_FSL_PCI_H
>> -#define __POWERPC_FSL_PCI_H
>> -
>> -struct platform_device;
>> -
>> -
>> -/* FSL PCI controller BRR1 register */
>> -#define PCI_FSL_BRR1 0xbf8
>> -#define PCI_FSL_BRR1_VER 0xffff
>> +#ifndef __PCI_COMMON_H
>> +#define __PCI_COMMON_H
>>
>> #define PCIE_LTSSM 0x0404 /* PCIE Link Training and Status */
>> #define PCIE_LTSSM_L0 0x16 /* L0 state */
>> @@ -52,7 +45,7 @@ struct pci_inbound_window_regs {
>> u8 res2[12];
>> };
>>
>> -/* PCI/PCI Express IO block registers for 85xx/86xx */
>> +/* PCI/PCI Express IO block registers for 85xx/86xx/LS */
>> struct ccsr_pci {
>> __be32 config_addr; /* 0x.000 - PCI/PCIE Configuration Address Register */
>> __be32 config_data; /* 0x.004 - PCI/PCIE Configuration Data Register */
>> @@ -109,33 +102,5 @@ struct ccsr_pci {
>>
>> };
>>
>> -extern int fsl_add_bridge(struct platform_device *pdev, int is_primary);
>> -extern void fsl_pcibios_fixup_bus(struct pci_bus *bus);
>> -extern int mpc83xx_add_bridge(struct device_node *dev);
>> -u64 fsl_pci_immrbar_base(struct pci_controller *hose);
>> -
>> -extern struct device_node *fsl_pci_primary;
>> -
>> -#ifdef CONFIG_PCI
>> -void fsl_pci_assign_primary(void);
>> -#else
>> -static inline void fsl_pci_assign_primary(void) {}
>> -#endif
>> -
>> -#ifdef CONFIG_EDAC_MPC85XX
>> -int mpc85xx_pci_err_probe(struct platform_device *op);
>> -#else
>> -static inline int mpc85xx_pci_err_probe(struct platform_device *op)
>> -{
>> - return -ENOTSUPP;
>> -}
>> -#endif
>> -
>> -#ifdef CONFIG_FSL_PCI
>> -extern int fsl_pci_mcheck_exception(struct pt_regs *);
>> -#else
>> -static inline int fsl_pci_mcheck_exception(struct pt_regs *regs) {return 0; }
>> -#endif
>> -
>> -#endif /* __POWERPC_FSL_PCI_H */
>> +#endif /* __PCI_COMMON_H */
>> #endif /* __KERNEL__ */
>> --
>> 1.8.1.2
>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20131009/444e5ef8/attachment-0001.html>
More information about the Linuxppc-dev
mailing list