[PATCH 18/23] powerpc/eeh: PowerNV EEH backends
Gavin Shan
shangw at linux.vnet.ibm.com
Thu May 30 18:24:00 EST 2013
The patch adds EEH backends for PowerNV platform. It's notable that
part of those EEH backends call to the I/O chip dependent backends.
Signed-off-by: Gavin Shan <shangw at linux.vnet.ibm.com>
---
arch/powerpc/platforms/powernv/Makefile | 2 +-
arch/powerpc/platforms/powernv/eeh-powernv.c | 380 ++++++++++++++++++++++++++
2 files changed, 381 insertions(+), 1 deletions(-)
create mode 100644 arch/powerpc/platforms/powernv/eeh-powernv.c
diff --git a/arch/powerpc/platforms/powernv/Makefile b/arch/powerpc/platforms/powernv/Makefile
index 09bd0cb..7fe5951 100644
--- a/arch/powerpc/platforms/powernv/Makefile
+++ b/arch/powerpc/platforms/powernv/Makefile
@@ -3,4 +3,4 @@ obj-y += opal-rtc.o opal-nvram.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_PCI) += pci.o pci-p5ioc2.o pci-ioda.o
-obj-$(CONFIG_EEH) += eeh-ioda.o
+obj-$(CONFIG_EEH) += eeh-ioda.o eeh-powernv.o
diff --git a/arch/powerpc/platforms/powernv/eeh-powernv.c b/arch/powerpc/platforms/powernv/eeh-powernv.c
new file mode 100644
index 0000000..12fc240
--- /dev/null
+++ b/arch/powerpc/platforms/powernv/eeh-powernv.c
@@ -0,0 +1,380 @@
+/*
+ * The file intends to implement the platform dependent EEH operations on
+ * powernv platform. Actually, the powernv was created in order to fully
+ * hypervisor support.
+ *
+ * Copyright Benjamin Herrenschmidt & Gavin Shan, IBM Corporation 2013.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/atomic.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/msi.h>
+#include <linux/of.h>
+#include <linux/pci.h>
+#include <linux/proc_fs.h>
+#include <linux/rbtree.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <linux/spinlock.h>
+
+#include <asm/eeh.h>
+#include <asm/eeh_event.h>
+#include <asm/io.h>
+#include <asm/iommu.h>
+#include <asm/machdep.h>
+#include <asm/msi_bitmap.h>
+#include <asm/opal.h>
+#include <asm/ppc-pci.h>
+
+#include "powernv.h"
+#include "pci.h"
+
+/**
+ * powernv_eeh_init - EEH platform dependent initialization
+ *
+ * EEH platform dependent initialization on powernv
+ */
+static int powernv_eeh_init(void)
+{
+ /* Set EEH probe mode */
+ eeh_probe_mode_set(EEH_PROBE_MODE_DEV);
+
+ return 0;
+}
+
+/**
+ * powernv_eeh_post_init - EEH platform dependent post initialization
+ *
+ * EEH platform dependent post initialization on powernv. When
+ * the function is called, the EEH PEs and devices should have
+ * been built. If the I/O cache staff has been built, EEH is
+ * ready to supply service.
+ */
+static int powernv_eeh_post_init(void)
+{
+ struct pci_controller *hose;
+ struct pnv_phb *phb;
+ int ret = 0;
+
+ list_for_each_entry(hose, &hose_list, list_node) {
+ phb = hose->private_data;
+
+ if (phb->eeh_ops && phb->eeh_ops->post_init) {
+ ret = phb->eeh_ops->post_init(hose);
+ if (ret)
+ break;
+ }
+ }
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_dev_probe - Do probe on PCI device
+ * @dev: PCI device
+ * @flag: unused
+ *
+ * When EEH module is installed during system boot, all PCI devices
+ * are checked one by one to see if it supports EEH. The function
+ * is introduced for the purpose. By default, EEH has been enabled
+ * on all PCI devices. That's to say, we only need do necessary
+ * initialization on the corresponding eeh device and create PE
+ * accordingly.
+ *
+ * It's notable that's unsafe to retrieve the EEH device through
+ * the corresponding PCI device. During the PCI device hotplug, which
+ * was possiblly triggered by EEH core, the binding between EEH device
+ * and the PCI device isn't built yet.
+ */
+static void *powernv_eeh_dev_probe(struct pci_dev *dev, void *flag)
+{
+ struct pci_controller *hose = pci_bus_to_host(dev->bus);
+ struct pnv_phb *phb = hose->private_data;
+ struct device_node *dn = pci_device_to_OF_node(dev);
+ struct eeh_dev *edev = of_node_to_eeh_dev(dn);
+
+ /*
+ * When probing the root bridge, which doesn't have any
+ * subordinate PCI devices. We don't have OF node for
+ * the root bridge. So it's not reasonable to continue
+ * the probing.
+ */
+ if (!dn || !edev)
+ return NULL;
+
+ /* Skip for PCI-ISA bridge */
+ if ((dev->class >> 8) == PCI_CLASS_BRIDGE_ISA)
+ return NULL;
+
+ /* Initialize eeh device */
+ edev->class_code = dev->class;
+ edev->mode = 0;
+ edev->config_addr = ((dev->bus->number << 8) | dev->devfn);
+ edev->pe_config_addr = phb->bdfn_to_pe(phb, dev->bus, dev->devfn & 0xff);
+
+ /* Create PE */
+ eeh_add_to_parent_pe(edev);
+
+ /*
+ * Enable EEH explicitly so that we will do EEH check
+ * while accessing I/O stuff
+ *
+ * FIXME: Enable that for PHB3 later
+ */
+ if (phb->type == PNV_PHB_IODA1)
+ eeh_subsystem_enabled = 1;
+
+ /* Save memory bars */
+ eeh_save_bars(edev);
+
+ return NULL;
+}
+
+/**
+ * powernv_eeh_set_option - Initialize EEH or MMIO/DMA reenable
+ * @pe: EEH PE
+ * @option: operation to be issued
+ *
+ * The function is used to control the EEH functionality globally.
+ * Currently, following options are support according to PAPR:
+ * Enable EEH, Disable EEH, Enable MMIO and Enable DMA
+ */
+static int powernv_eeh_set_option(struct eeh_pe *pe, int option)
+{
+ struct pci_controller *hose = pe->phb;
+ struct pnv_phb *phb = hose->private_data;
+ int ret = -EEXIST;
+
+ /*
+ * What we need do is pass it down for hardware
+ * implementation to handle it.
+ */
+ if (phb->eeh_ops && phb->eeh_ops->set_option)
+ ret = phb->eeh_ops->set_option(pe, option);
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_get_pe_addr - Retrieve PE address
+ * @pe: EEH PE
+ *
+ * Retrieve the PE address according to the given tranditional
+ * PCI BDF (Bus/Device/Function) address.
+ */
+static int powernv_eeh_get_pe_addr(struct eeh_pe *pe)
+{
+ return pe->addr;
+}
+
+/**
+ * powernv_eeh_get_state - Retrieve PE state
+ * @pe: EEH PE
+ * @state: return value
+ *
+ * Retrieve the state of the specified PE. For IODA-compitable
+ * platform, it should be retrieved from IODA table. Therefore,
+ * we prefer passing down to hardware implementation to handle
+ * it.
+ */
+static int powernv_eeh_get_state(struct eeh_pe *pe, int *state)
+{
+ struct pci_controller *hose = pe->phb;
+ struct pnv_phb *phb = hose->private_data;
+ int ret = EEH_STATE_NOT_SUPPORT;
+
+ if (phb->eeh_ops && phb->eeh_ops->get_state)
+ ret = phb->eeh_ops->get_state(pe, state);
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_reset - Reset the specified PE
+ * @pe: EEH PE
+ * @option: reset option
+ *
+ * Reset the specified PE
+ */
+static int powernv_eeh_reset(struct eeh_pe *pe, int option)
+{
+ struct pci_controller *hose = pe->phb;
+ struct pnv_phb *phb = hose->private_data;
+ int ret = -EEXIST;
+
+ if (phb->eeh_ops && phb->eeh_ops->reset)
+ ret = phb->eeh_ops->reset(pe, option);
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_wait_state - Wait for PE state
+ * @pe: EEH PE
+ * @max_wait: maximal period in microsecond
+ *
+ * Wait for the state of associated PE. It might take some time
+ * to retrieve the PE's state.
+ */
+static int powernv_eeh_wait_state(struct eeh_pe *pe, int max_wait)
+{
+ int ret;
+ int mwait;
+
+ while (1) {
+ ret = powernv_eeh_get_state(pe, &mwait);
+
+ /*
+ * If the PE's state is temporarily unavailable,
+ * we have to wait for the specified time. Otherwise,
+ * the PE's state will be returned immediately.
+ */
+ if (ret != EEH_STATE_UNAVAILABLE)
+ return ret;
+
+ max_wait -= mwait;
+ msleep(mwait);
+ }
+
+ return EEH_STATE_NOT_SUPPORT;
+}
+
+/**
+ * powernv_eeh_get_log - Retrieve error log
+ * @pe: EEH PE
+ * @severity: temporary or permanent error log
+ * @drv_log: driver log to be combined with retrieved error log
+ * @len: length of driver log
+ *
+ * Retrieve the temporary or permanent error from the PE.
+ */
+static int powernv_eeh_get_log(struct eeh_pe *pe, int severity,
+ char *drv_log, unsigned long len)
+{
+ struct pci_controller *hose = pe->phb;
+ struct pnv_phb *phb = hose->private_data;
+ int ret = -EEXIST;
+
+ if (phb->eeh_ops && phb->eeh_ops->get_log)
+ ret = phb->eeh_ops->get_log(pe, severity, drv_log, len);
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_configure_bridge - Configure PCI bridges in the indicated PE
+ * @pe: EEH PE
+ *
+ * The function will be called to reconfigure the bridges included
+ * in the specified PE so that the mulfunctional PE would be recovered
+ * again.
+ */
+static int powernv_eeh_configure_bridge(struct eeh_pe *pe)
+{
+ struct pci_controller *hose = pe->phb;
+ struct pnv_phb *phb = hose->private_data;
+ int ret = 0;
+
+ if (phb->eeh_ops && phb->eeh_ops->configure_bridge)
+ ret = phb->eeh_ops->configure_bridge(pe);
+
+ return ret;
+}
+
+/**
+ * powernv_eeh_read_config - Read PCI config space
+ * @dn: device node
+ * @where: PCI address
+ * @size: size to read
+ * @val: return value
+ *
+ * Read config space from the speicifed device
+ */
+static int powernv_eeh_read_config(struct device_node *dn, int where,
+ int size, u32 *val)
+{
+ struct eeh_dev *edev = of_node_to_eeh_dev(dn);
+ struct pci_dev *dev = eeh_dev_to_pci_dev(edev);
+ struct pci_controller *hose = edev->phb;
+
+ return hose->ops->read(dev->bus, dev->devfn, where, size, val);
+}
+
+/**
+ * powernv_eeh_write_config - Write PCI config space
+ * @dn: device node
+ * @where: PCI address
+ * @size: size to write
+ * @val: value to be written
+ *
+ * Write config space to the specified device
+ */
+static int powernv_eeh_write_config(struct device_node *dn, int where,
+ int size, u32 val)
+{
+ struct eeh_dev *edev = of_node_to_eeh_dev(dn);
+ struct pci_dev *dev = eeh_dev_to_pci_dev(edev);
+ struct pci_controller *hose = edev->phb;
+
+ hose = pci_bus_to_host(dev->bus);
+
+ return hose->ops->write(dev->bus, dev->devfn, where, size, val);
+}
+
+static struct eeh_ops powernv_eeh_ops = {
+ .name = "powernv",
+ .init = powernv_eeh_init,
+ .post_init = powernv_eeh_post_init,
+ .of_probe = NULL,
+ .dev_probe = powernv_eeh_dev_probe,
+ .set_option = powernv_eeh_set_option,
+ .get_pe_addr = powernv_eeh_get_pe_addr,
+ .get_state = powernv_eeh_get_state,
+ .reset = powernv_eeh_reset,
+ .wait_state = powernv_eeh_wait_state,
+ .get_log = powernv_eeh_get_log,
+ .configure_bridge = powernv_eeh_configure_bridge,
+ .read_config = powernv_eeh_read_config,
+ .write_config = powernv_eeh_write_config
+};
+
+/**
+ * eeh_powernv_init - Register platform dependent EEH operations
+ *
+ * EEH initialization on powernv platform. This function should be
+ * called before any EEH related functions.
+ */
+static int __init eeh_powernv_init(void)
+{
+ int ret = -EINVAL;
+
+ if (!machine_is(powernv))
+ return ret;
+
+ ret = eeh_ops_register(&powernv_eeh_ops);
+ if (!ret)
+ pr_info("EEH: PowerNV platform initialized\n");
+ else
+ pr_info("EEH: Failed to initialize PowerNV platform (%d)\n", ret);
+
+ return ret;
+}
+
+early_initcall(eeh_powernv_init);
--
1.7.5.4
More information about the Linuxppc-dev
mailing list