SATA FSL and upstreaming

[Benjamin Herrenschmidt]

On Thu, 2013-05-16 at 06:17 +0000, Zang Roy-R61911 wrote:
> Do you try slot7?
> PCIe1 connects to slot7 directly.

I tried all slots. None of them sees any card. The card also doesn't
seem to be powered up (none of the LEDs blink, it's an e1000 since I
don't have networking with upstream).

I also tried a different card and uboot is pretty adamant at saying "no
link" :-)

I'll try to update the RCW when I know how to do it :-)

Cheers,
Ben.

> Roy
> 
> > -----Original Message-----
> > From: Benjamin Herrenschmidt [mailto:benh at kernel.crashing.org]
> > Sent: Thursday, May 16, 2013 2:09 PM
> > To: Zang Roy-R61911
> > Cc: Bhushan Bharat-R65777; Liu Qiang-B32616; Fleming Andy-AFLEMING;
> > linuxppc-dev at lists.ozlabs.org; Xie Shaohui-B21989
> > Subject: Re: SATA FSL and upstreaming
> > 
> > On Thu, 2013-05-16 at 06:05 +0000, Zang Roy-R61911 wrote:
> > > I do not suggest changing the RCW. If the RCW is broken on Ben's side,
> > > it is not easy to recover for him.
> > > Let's check the U-boot output first.
> > 
> > U-Boot 2013.01-00009-g7bcd7f4 (Mar 14 2013 - 14:23:16)
> > 
> > CPU0:  P5020E, Version: 1.0, (0x82280010)
> > Core:  E5500, Version: 1.0, (0x80240010)
> > Clock Configuration:
> >        CPU0:2000 MHz, CPU1:2000 MHz,
> >        CCB:800  MHz,
> >        DDR:666.667 MHz (1333.333 MT/s data rate) (Asynchronous), LBC:100
> > MHz
> >        FMAN1: 600 MHz
> >        QMAN:  400 MHz
> >        PME:   400 MHz
> > L1:    D-cache 32 kB enabled
> >        I-cache 32 kB enabled
> > Board: P5020DS, Sys ID: 0x1c, Sys Ver: 0x12, FPGA Ver: 0x05, vBank: 0
> > Reset Configuration Word (RCW):
> >        00000000: 0c540000 00000000 1e120000 00000000
> >        00000010: d8984a01 03002000 de800000 41000000
> >        00000020: 00000000 00000000 00000000 10070000
> >        00000030: 00000000 00000000 00000000 00000000
> > SERDES Reference Clocks: Bank1=100Mhz Bank2=125Mhz Bank3=125Mhz
> > I2C:   ready
> > SPI:   ready
> > DRAM:  Initializing....using SPD
> > Detected UDIMM i-DIMM
> > Detected UDIMM i-DIMM
> > 2 GiB left unmapped
> > 4 GiB (DDR3, 64-bit, CL=9, ECC on)
> >        DDR Controller Interleaving Mode: cache line
> >        DDR Chip-Select Interleaving Mode: CS0+CS1
> > Testing 0x00000000 - 0x7fffffff
> > Testing 0x80000000 - 0xffffffff
> > Remap DDR 2 GiB left unmapped
> > 
> > POST memory PASSED
> > Flash: 128 MiB
> > L2:    512 KB enabled
> > Corenet Platform Cache: 2048 KB enabled
> > SRIO1: disabled
> > SRIO2: disabled
> > NAND:  1024 MiB
> > MMC:  FSL_SDHC: 0
> > EEPROM: NXID v1
> > PCIe1: Root Complex, no link, regs @ 0xfe200000
> > PCIe1: Bus 00 - 00
> > PCIe2: disabled
> > PCIe3: Root Complex, no link, regs @ 0xfe202000
> > PCIe3: Bus 01 - 01
> > PCIe4: disabled
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   Initializing Fman
> > Fman1: Uploading microcode version 106.1.7
> > PHY reset timed out
> > PHY reset timed out
> > PHY reset timed out
> > PHY reset timed out
> > FM1 at DTSEC1, FM1 at DTSEC2, FM1 at DTSEC3, FM1 at DTSEC4, FM1 at DTSEC5, FM1 at TGEC1
> > Hit any key to stop autoboot:  0
> > =>
> > 
> > Cheers,
> > Ben.
> > 
> > 
>