[PATCH v4 27/31] net: can: mscan: add common clock support for mpc512x

Gerhard Sittig gsi at denx.de
Wed Aug 7 06:44:07 EST 2013


implement a .get_clock() callback for the MPC512x platform which uses
the common clock infrastructure (eliminating direct access to the clock
control registers from within the CAN network driver), and provide the
corresponding .put_clock() callback to release resources after use

keep the previous implementation of MPC512x support in place during
migration, since common clock support is optional

acquire both the 'ipg' as well as "can" clock items in the mscan driver,
remove pre-enable workarounds for the BDLC (CAN related 'ipg') as well
as the CAN related MCLK (bitrate) items in the platform's clock driver

this change is neutral to the MPC5200 platform

Signed-off-by: Gerhard Sittig <gsi at denx.de>
---
 arch/powerpc/platforms/512x/clock-commonclk.c |    3 -
 drivers/net/can/mscan/mpc5xxx_can.c           |  179 +++++++++++++++++++++++++
 2 files changed, 179 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/platforms/512x/clock-commonclk.c b/arch/powerpc/platforms/512x/clock-commonclk.c
index e5e9cbe..afbb01d 100644
--- a/arch/powerpc/platforms/512x/clock-commonclk.c
+++ b/arch/powerpc/platforms/512x/clock-commonclk.c
@@ -669,9 +669,6 @@ static void mpc512x_clk_setup_clock_tree(int busfreq)
 	/* some are not yet acquired by their respective drivers */
 	clk_prepare_enable(clks[MPC512x_CLK_PSC3_MCLK]);/* serial console */
 	clk_prepare_enable(clks[MPC512x_CLK_DIU]);	/* display */
-	clk_prepare_enable(clks[MPC512x_CLK_BDLC]);
-	for (mclk_idx = 0; mclk_idx < ARRAY_SIZE(mclk_mscan_data); mclk_idx++)
-		clk_prepare_enable(clks[MPC512x_CLK_MSCAN0_MCLK + mclk_idx]);
 }
 
 /*
diff --git a/drivers/net/can/mscan/mpc5xxx_can.c b/drivers/net/can/mscan/mpc5xxx_can.c
index e59b3a3..f48f129 100644
--- a/drivers/net/can/mscan/mpc5xxx_can.c
+++ b/drivers/net/can/mscan/mpc5xxx_can.c
@@ -109,6 +109,177 @@ static u32 mpc52xx_can_get_clock(struct platform_device *ofdev,
 #endif /* CONFIG_PPC_MPC52xx */
 
 #ifdef CONFIG_PPC_MPC512x
+
+#if IS_ENABLED(CONFIG_COMMON_CLK)
+
+static u32 mpc512x_can_get_clock(struct platform_device *ofdev,
+				 const char *clock_source, int *mscan_clksrc)
+{
+	struct device_node *np;
+	u32 clockdiv;
+	enum {
+		CLK_FROM_AUTO,
+		CLK_FROM_IPS,
+		CLK_FROM_SYS,
+		CLK_FROM_REF,
+	} clk_from;
+	struct clk *clk_in, *clk_can;
+	unsigned long freq_calc;
+	struct mscan_priv *priv;
+	struct clk *clk_ipg;
+
+	/* the caller passed in the clock source spec that was read from
+	 * the device tree, get the optional clock divider as well
+	 */
+	np = ofdev->dev.of_node;
+	clockdiv = 1;
+	of_property_read_u32(np, "fsl,mscan-clock-divider", &clockdiv);
+	dev_dbg(&ofdev->dev, "device tree specs: clk src[%s] div[%d]\n",
+		clock_source ? clock_source : "<NULL>", clockdiv);
+
+	/* when clock-source is 'ip', the CANCTL1[CLKSRC] bit needs to
+	 * get set, and the 'ips' clock is the input to the MSCAN
+	 * component
+	 *
+	 * for clock-source values of 'ref' or 'sys' the CANCTL1[CLKSRC]
+	 * bit needs to get cleared, an optional clock-divider may have
+	 * been specified (the default value is 1), the appropriate
+	 * MSCAN related MCLK is the input to the MSCAN component
+	 *
+	 * in the absence of a clock-source spec, first an optimal clock
+	 * gets determined based on the 'sys' clock, if that fails the
+	 * 'ref' clock is used
+	 */
+	clk_from = CLK_FROM_AUTO;
+	if (clock_source) {
+		/* interpret the device tree's spec for the clock source */
+		if (!strcmp(clock_source, "ip"))
+			clk_from = CLK_FROM_IPS;
+		else if (!strcmp(clock_source, "sys"))
+			clk_from = CLK_FROM_SYS;
+		else if (!strcmp(clock_source, "ref"))
+			clk_from = CLK_FROM_REF;
+		else
+			goto err_invalid;
+		dev_dbg(&ofdev->dev, "got a clk source spec[%d]\n", clk_from);
+	}
+	if (clk_from == CLK_FROM_AUTO) {
+		/* no spec so far, try the 'sys' clock; round to the
+		 * next MHz and see if we can get a multiple of 16MHz
+		 */
+		dev_dbg(&ofdev->dev, "no clk source spec, trying SYS\n");
+		clk_in = devm_clk_get(&ofdev->dev, "sys");
+		if (IS_ERR(clk_in))
+			goto err_notavail;
+		freq_calc = clk_get_rate(clk_in);
+		freq_calc +=  499999;
+		freq_calc /= 1000000;
+		freq_calc *= 1000000;
+		if ((freq_calc % 16000000) == 0) {
+			clk_from = CLK_FROM_SYS;
+			clockdiv = freq_calc / 16000000;
+			dev_dbg(&ofdev->dev,
+				"clk fit, sys[%lu] div[%d] freq[%lu]\n",
+				freq_calc, clockdiv, freq_calc / clockdiv);
+		}
+	}
+	if (clk_from == CLK_FROM_AUTO) {
+		/* no spec so far, use the 'ref' clock */
+		dev_dbg(&ofdev->dev, "no clk source spec, trying REF\n");
+		clk_in = devm_clk_get(&ofdev->dev, "ref");
+		if (IS_ERR(clk_in))
+			goto err_notavail;
+		clk_from = CLK_FROM_REF;
+		freq_calc = clk_get_rate(clk_in);
+		dev_dbg(&ofdev->dev,
+			"clk fit, ref[%lu] (no div) freq[%lu]\n",
+			freq_calc, freq_calc);
+	}
+
+	/* select IPS or MCLK as the MSCAN input (returned to the caller),
+	 * setup the MCLK mux source and rate if applicable, apply the
+	 * optionally specified or derived above divider, and determine
+	 * the actual resulting clock rate to return to the caller
+	 */
+	switch (clk_from) {
+	case CLK_FROM_IPS:
+		clk_can = devm_clk_get(&ofdev->dev, "ips");
+		if (IS_ERR(clk_can))
+			goto err_notavail;
+		priv = netdev_priv(dev_get_drvdata(&ofdev->dev));
+		priv->clk_can = clk_can;
+		freq_calc = clk_get_rate(clk_can);
+		*mscan_clksrc = MSCAN_CLKSRC_IPS;
+		dev_dbg(&ofdev->dev, "clk from IPS, clksrc[%d] freq[%lu]\n",
+			*mscan_clksrc, freq_calc);
+		break;
+	case CLK_FROM_SYS:
+	case CLK_FROM_REF:
+		clk_can = devm_clk_get(&ofdev->dev, "mclk");
+		if (IS_ERR(clk_can))
+			goto err_notavail;
+		priv = netdev_priv(dev_get_drvdata(&ofdev->dev));
+		priv->clk_can = clk_can;
+		if (clk_from == CLK_FROM_SYS)
+			clk_in = devm_clk_get(&ofdev->dev, "sys");
+		if (clk_from == CLK_FROM_REF)
+			clk_in = devm_clk_get(&ofdev->dev, "ref");
+		if (IS_ERR(clk_in))
+			goto err_notavail;
+		clk_set_parent(clk_can, clk_in);
+		freq_calc = clk_get_rate(clk_in);
+		freq_calc /= clockdiv;
+		clk_set_rate(clk_can, freq_calc);
+		freq_calc = clk_get_rate(clk_can);
+		*mscan_clksrc = MSCAN_CLKSRC_BUS;
+		dev_dbg(&ofdev->dev, "clk from MCLK, clksrc[%d] freq[%lu]\n",
+			*mscan_clksrc, freq_calc);
+		break;
+	default:
+		goto err_invalid;
+	}
+
+	/* the above clk_can item is used for the bitrate, access to
+	 * the peripheral's register set needs the clk_ipg item
+	 */
+	clk_ipg = devm_clk_get(&ofdev->dev, "ipg");
+	if (IS_ERR(clk_ipg))
+		goto err_notavail_ipg;
+	if (clk_prepare_enable(clk_ipg))
+		goto err_notavail_ipg;
+	priv = netdev_priv(dev_get_drvdata(&ofdev->dev));
+	priv->clk_ipg = clk_ipg;
+
+	/* return the determined clock source rate */
+	return freq_calc;
+
+err_invalid:
+	dev_err(&ofdev->dev, "invalid clock source specification\n");
+	/* clock source rate could not get determined */
+	return 0;
+
+err_notavail:
+	dev_err(&ofdev->dev, "cannot acquire or setup bitrate clock source\n");
+	/* clock source rate could not get determined */
+	return 0;
+
+err_notavail_ipg:
+	dev_err(&ofdev->dev, "cannot acquire or setup register clock\n");
+	/* clock source rate could not get determined */
+	return 0;
+}
+
+static void mpc512x_can_put_clock(struct platform_device *ofdev)
+{
+	struct mscan_priv *priv;
+
+	priv = netdev_priv(dev_get_drvdata(&ofdev->dev));
+	if (priv->clk_ipg)
+		clk_disable_unprepare(priv->clk_ipg);
+}
+
+#else	/* COMMON_CLK */
+
 struct mpc512x_clockctl {
 	u32 spmr;		/* System PLL Mode Reg */
 	u32 sccr[2];		/* System Clk Ctrl Reg 1 & 2 */
@@ -239,12 +410,18 @@ exit_put:
 	of_node_put(np_clock);
 	return freq;
 }
+
+#define mpc512x_can_put_clock NULL
+
+#endif	/* COMMON_CLK */
+
 #else /* !CONFIG_PPC_MPC512x */
 static u32 mpc512x_can_get_clock(struct platform_device *ofdev,
 				 const char *clock_name, int *mscan_clksrc)
 {
 	return 0;
 }
+#define mpc512x_can_put_clock NULL
 #endif /* CONFIG_PPC_MPC512x */
 
 static const struct of_device_id mpc5xxx_can_table[];
@@ -386,11 +563,13 @@ static int mpc5xxx_can_resume(struct platform_device *ofdev)
 static const struct mpc5xxx_can_data mpc5200_can_data = {
 	.type = MSCAN_TYPE_MPC5200,
 	.get_clock = mpc52xx_can_get_clock,
+	/* .put_clock not applicable */
 };
 
 static const struct mpc5xxx_can_data mpc5121_can_data = {
 	.type = MSCAN_TYPE_MPC5121,
 	.get_clock = mpc512x_can_get_clock,
+	.put_clock = mpc512x_can_put_clock,
 };
 
 static const struct of_device_id mpc5xxx_can_table[] = {
-- 
1.7.10.4



More information about the Linuxppc-dev mailing list