[PATCH][v4] NAND Machine support for Integrated Flash Controller
Prabhakar Kushwaha
prabhakar at freescale.com
Thu Mar 15 16:34:23 EST 2012
Integrated Flash Controller(IFC) can be used to hook NAND Flash
chips using NAND Flash Machine available on it.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat at freescale.com>
Signed-off-by: Scott Wood <scottwood at freescale.com>
Signed-off-by: Li Yang <leoli at freescale.com>
Signed-off-by: Liu Shuo <b35362 at freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
---
Beased on http://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git
branch master
Tested on P1010RDB
Changes for v2: Ported IFC driver for linux-3.2.0-rc3
- Use chip->bbt_options for BBT
- Use mtd_device_parse_register instead of old parse_mtd_partitions
Changes for v3: Squashed following patch to make singe NAND driver patch
- mtd/nand:Fix wrong usage of is_blank() in fsl_ifc_run_command
http://patchwork.ozlabs.org/patch/136547/
- mtd/nand: Fix IFC driver to support 2K NAND page
http://patchwork.ozlabs.org/patch/135010/
Changes for v4:
- fsl_ifc_run_command: handled wait_event_timeout timeout-return case
- Removed unused full_page variable
- fsl_ifc_read_page: Updated Error message
- fsl_ifc_nand_probe: removed possible memory leak for priv variable
drivers/mtd/nand/Kconfig | 10 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/fsl_ifc_nand.c | 1072 +++++++++++++++++++++++++++++++++++++++
3 files changed, 1083 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/fsl_ifc_nand.c
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index dd02792..2652bcc 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -462,6 +462,16 @@ config MTD_NAND_FSL_ELBC
Enabling this option will enable you to use this to control
external NAND devices.
+config MTD_NAND_FSL_IFC
+ tristate "NAND support for Freescale IFC controller"
+ depends on MTD_NAND && FSL_SOC
+ select FSL_IFC
+ help
+ Various Freescale chips e.g P1010, include a NAND Flash machine
+ with built-in hardware ECC capabilities.
+ Enabling this option will enable you to use this to control
+ external NAND devices.
+
config MTD_NAND_FSL_UPM
tristate "Support for NAND on Freescale UPM"
depends on PPC_83xx || PPC_85xx
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 618f4ba..19bc8cb 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_MTD_ALAUDA) += alauda.o
obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o
obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o
obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o
obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c
new file mode 100644
index 0000000..c30ac7b
--- /dev/null
+++ b/drivers/mtd/nand/fsl_ifc_nand.c
@@ -0,0 +1,1072 @@
+/*
+ * Freescale Integrated Flash Controller NAND driver
+ *
+ * Copyright 2011-2012 Freescale Semiconductor, Inc
+ *
+ * Author: Dipen Dudhat <Dipen.Dudhat at freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand_ecc.h>
+#include <asm/fsl_ifc.h>
+
+#define ERR_BYTE 0xFF /* Value returned for read
+ bytes when read failed */
+#define IFC_TIMEOUT_MSECS 500 /* Maximum number of mSecs to wait
+ for IFC NAND Machine */
+
+struct fsl_ifc_ctrl;
+
+/* mtd information per set */
+struct fsl_ifc_mtd {
+ struct mtd_info mtd;
+ struct nand_chip chip;
+ struct fsl_ifc_ctrl *ctrl;
+
+ struct device *dev;
+ int bank; /* Chip select bank number */
+ unsigned int bufnum_mask; /* bufnum = page & bufnum_mask */
+ u8 __iomem *vbase; /* Chip select base virtual address */
+};
+
+/* overview of the fsl ifc controller */
+struct fsl_ifc_nand_ctrl {
+ struct nand_hw_control controller;
+ struct fsl_ifc_mtd *chips[FSL_IFC_BANK_COUNT];
+
+ u8 __iomem *addr; /* Address of assigned IFC buffer */
+ unsigned int page; /* Last page written to / read from */
+ unsigned int read_bytes;/* Number of bytes read during command */
+ unsigned int column; /* Saved column from SEQIN */
+ unsigned int index; /* Pointer to next byte to 'read' */
+ unsigned int oob; /* Non zero if operating on OOB data */
+ unsigned int eccread; /* Non zero for a full-page ECC read */
+ unsigned int counter; /* counter for the initializations */
+};
+
+static struct fsl_ifc_nand_ctrl *ifc_nand_ctrl;
+
+/* 512-byte page with 4-bit ECC, 8-bit */
+static struct nand_ecclayout oob_512_8bit_ecc4 = {
+ .eccbytes = 8,
+ .eccpos = {8, 9, 10, 11, 12, 13, 14, 15},
+ .oobfree = { {0, 5}, {6, 2} },
+};
+
+/* 512-byte page with 4-bit ECC, 16-bit */
+static struct nand_ecclayout oob_512_16bit_ecc4 = {
+ .eccbytes = 8,
+ .eccpos = {8, 9, 10, 11, 12, 13, 14, 15},
+ .oobfree = { {2, 6}, },
+};
+
+/* 2048-byte page size with 4-bit ECC */
+static struct nand_ecclayout oob_2048_ecc4 = {
+ .eccbytes = 32,
+ .eccpos = {
+ 8, 9, 10, 11, 12, 13, 14, 15,
+ 16, 17, 18, 19, 20, 21, 22, 23,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ },
+ .oobfree = { {2, 6}, {40, 24} },
+};
+
+/* 4096-byte page size with 4-bit ECC */
+static struct nand_ecclayout oob_4096_ecc4 = {
+ .eccbytes = 64,
+ .eccpos = {
+ 8, 9, 10, 11, 12, 13, 14, 15,
+ 16, 17, 18, 19, 20, 21, 22, 23,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63,
+ 64, 65, 66, 67, 68, 69, 70, 71,
+ },
+ .oobfree = { {2, 6}, {72, 56} },
+};
+
+/* 4096-byte page size with 8-bit ECC -- requires 218-byte OOB */
+static struct nand_ecclayout oob_4096_ecc8 = {
+ .eccbytes = 128,
+ .eccpos = {
+ 8, 9, 10, 11, 12, 13, 14, 15,
+ 16, 17, 18, 19, 20, 21, 22, 23,
+ 24, 25, 26, 27, 28, 29, 30, 31,
+ 32, 33, 34, 35, 36, 37, 38, 39,
+ 40, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55,
+ 56, 57, 58, 59, 60, 61, 62, 63,
+ 64, 65, 66, 67, 68, 69, 70, 71,
+ 72, 73, 74, 75, 76, 77, 78, 79,
+ 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95,
+ 96, 97, 98, 99, 100, 101, 102, 103,
+ 104, 105, 106, 107, 108, 109, 110, 111,
+ 112, 113, 114, 115, 116, 117, 118, 119,
+ 120, 121, 122, 123, 124, 125, 126, 127,
+ 128, 129, 130, 131, 132, 133, 134, 135,
+ },
+ .oobfree = { {2, 6}, {136, 82} },
+};
+
+
+/*
+ * Generic flash bbt descriptors
+ */
+static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
+static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 2, /* 0 on 8-bit small page */
+ .len = 4,
+ .veroffs = 6,
+ .maxblocks = 4,
+ .pattern = bbt_pattern,
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE |
+ NAND_BBT_2BIT | NAND_BBT_VERSION,
+ .offs = 2, /* 0 on 8-bit small page */
+ .len = 4,
+ .veroffs = 6,
+ .maxblocks = 4,
+ .pattern = mirror_pattern,
+};
+
+/*
+ * Set up the IFC hardware block and page address fields, and the ifc nand
+ * structure addr field to point to the correct IFC buffer in memory
+ */
+static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+ int buf_num;
+
+ ifc_nand_ctrl->page = page_addr;
+ /* Program ROW0/COL0 */
+ out_be32(&ifc->ifc_nand.row0, page_addr);
+ out_be32(&ifc->ifc_nand.col0, (oob ? IFC_NAND_COL_MS : 0) | column);
+
+ buf_num = page_addr & priv->bufnum_mask;
+
+ ifc_nand_ctrl->addr = priv->vbase + buf_num * (mtd->writesize * 2);
+ ifc_nand_ctrl->index = column;
+
+ /* for OOB data point to the second half of the buffer */
+ if (oob)
+ ifc_nand_ctrl->index += mtd->writesize;
+}
+
+static int is_blank(struct mtd_info *mtd, unsigned int bufnum)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ u8 __iomem *addr = priv->vbase + bufnum * (mtd->writesize * 2);
+ u32 __iomem *mainarea = (u32 *)addr;
+ u8 __iomem *oob = addr + mtd->writesize;
+ int i;
+
+ for (i = 0; i < mtd->writesize / 4; i++) {
+ if (__raw_readl(&mainarea[i]) != 0xffffffff)
+ return 0;
+ }
+
+ for (i = 0; i < chip->ecc.layout->eccbytes; i++) {
+ int pos = chip->ecc.layout->eccpos[i];
+
+ if (__raw_readb(&oob[pos]) != 0xff)
+ return 0;
+ }
+
+ return 1;
+}
+
+/* returns nonzero if entire page is blank */
+static int check_read_ecc(struct mtd_info *mtd, struct fsl_ifc_ctrl *ctrl,
+ u32 *eccstat, unsigned int bufnum)
+{
+ u32 reg = eccstat[bufnum / 4];
+ int errors;
+
+ errors = (reg >> ((3 - bufnum % 4) * 8)) & 15;
+
+ return errors;
+}
+
+/*
+ * execute IFC NAND command and wait for it to complete
+ */
+static void fsl_ifc_run_command(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_nand_ctrl *nctrl = ifc_nand_ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+ u32 eccstat[4];
+ int i;
+
+ /* set the chip select for NAND Transaction */
+ out_be32(&ifc->ifc_nand.nand_csel, priv->bank << IFC_NAND_CSEL_SHIFT);
+
+ dev_vdbg(priv->dev,
+ "%s: fir0=%08x fcr0=%08x\n",
+ __func__,
+ in_be32(&ifc->ifc_nand.nand_fir0),
+ in_be32(&ifc->ifc_nand.nand_fcr0));
+
+ ctrl->nand_stat = 0;
+
+ /* start read/write seq */
+ out_be32(&ifc->ifc_nand.nandseq_strt, IFC_NAND_SEQ_STRT_FIR_STRT);
+
+ /* wait for command complete flag or timeout */
+ wait_event_timeout(ctrl->nand_wait, ctrl->nand_stat,
+ IFC_TIMEOUT_MSECS * HZ/1000);
+
+ /* ctrl->nand_stat will be updated from IRQ context */
+ if (!ctrl->nand_stat)
+ dev_err(priv->dev, "Controller is not responding\n");
+ if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_FTOER)
+ dev_err(priv->dev, "NAND Flash Timeout Error\n");
+ if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_WPER)
+ dev_err(priv->dev, "NAND Flash Write Protect Error\n");
+
+ if (nctrl->eccread) {
+ int errors;
+ int bufnum = nctrl->page & priv->bufnum_mask;
+ int sector = bufnum * chip->ecc.steps;
+ int sector_end = sector + chip->ecc.steps - 1;
+
+ for (i = sector / 4; i <= sector_end / 4; i++)
+ eccstat[i] = in_be32(&ifc->ifc_nand.nand_eccstat[i]);
+
+ for (i = sector; i <= sector_end; i++) {
+ errors = check_read_ecc(mtd, ctrl, eccstat, i);
+
+ if (errors == 15) {
+ /*
+ * Uncorrectable error.
+ * OK only if the whole page is blank.
+ *
+ * We disable ECCER reporting due to...
+ * erratum IFC-A002770 -- so report it now if we
+ * see an uncorrectable error in ECCSTAT.
+ */
+ if (!is_blank(mtd, bufnum))
+ ctrl->nand_stat |=
+ IFC_NAND_EVTER_STAT_ECCER;
+ break;
+ }
+
+ mtd->ecc_stats.corrected += errors;
+ }
+
+ nctrl->eccread = 0;
+ }
+}
+
+static void fsl_ifc_do_read(struct nand_chip *chip,
+ int oob,
+ struct mtd_info *mtd)
+{
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+
+ /* Program FIR/IFC_NAND_FCR0 for Small/Large page */
+ if (mtd->writesize > 512) {
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) |
+ (IFC_FIR_OP_CMD1 << IFC_NAND_FIR0_OP3_SHIFT) |
+ (IFC_FIR_OP_RBCD << IFC_NAND_FIR0_OP4_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fir1, 0x0);
+
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ (NAND_CMD_READ0 << IFC_NAND_FCR0_CMD0_SHIFT) |
+ (NAND_CMD_READSTART << IFC_NAND_FCR0_CMD1_SHIFT));
+ } else {
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) |
+ (IFC_FIR_OP_RBCD << IFC_NAND_FIR0_OP3_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fir1, 0x0);
+
+ if (oob)
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ NAND_CMD_READOOB << IFC_NAND_FCR0_CMD0_SHIFT);
+ else
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ NAND_CMD_READ0 << IFC_NAND_FCR0_CMD0_SHIFT);
+ }
+}
+
+/* cmdfunc send commands to the IFC NAND Machine */
+static void fsl_ifc_cmdfunc(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr) {
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+
+ /* clear the read buffer */
+ ifc_nand_ctrl->read_bytes = 0;
+ if (command != NAND_CMD_PAGEPROG)
+ ifc_nand_ctrl->index = 0;
+
+ switch (command) {
+ /* READ0 read the entire buffer to use hardware ECC. */
+ case NAND_CMD_READ0:
+ out_be32(&ifc->ifc_nand.nand_fbcr, 0);
+ set_addr(mtd, 0, page_addr, 0);
+
+ ifc_nand_ctrl->read_bytes = mtd->writesize + mtd->oobsize;
+ ifc_nand_ctrl->index += column;
+
+ if (chip->ecc.mode == NAND_ECC_HW)
+ ifc_nand_ctrl->eccread = 1;
+
+ fsl_ifc_do_read(chip, 0, mtd);
+ fsl_ifc_run_command(mtd);
+ return;
+
+ /* READOOB reads only the OOB because no ECC is performed. */
+ case NAND_CMD_READOOB:
+ out_be32(&ifc->ifc_nand.nand_fbcr, mtd->oobsize - column);
+ set_addr(mtd, column, page_addr, 1);
+
+ ifc_nand_ctrl->read_bytes = mtd->writesize + mtd->oobsize;
+
+ fsl_ifc_do_read(chip, 1, mtd);
+ fsl_ifc_run_command(mtd);
+
+ return;
+
+ /* READID must read all 8 possible bytes */
+ case NAND_CMD_READID:
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CMD0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_RB << IFC_NAND_FIR0_OP2_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ NAND_CMD_READID << IFC_NAND_FCR0_CMD0_SHIFT);
+ /* 8 bytes for manuf, device and exts */
+ out_be32(&ifc->ifc_nand.nand_fbcr, 8);
+ ifc_nand_ctrl->read_bytes = 8;
+
+ set_addr(mtd, 0, 0, 0);
+ fsl_ifc_run_command(mtd);
+ return;
+
+ /* ERASE1 stores the block and page address */
+ case NAND_CMD_ERASE1:
+ set_addr(mtd, 0, page_addr, 0);
+ return;
+
+ /* ERASE2 uses the block and page address from ERASE1 */
+ case NAND_CMD_ERASE2:
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_CMD1 << IFC_NAND_FIR0_OP2_SHIFT));
+
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ (NAND_CMD_ERASE1 << IFC_NAND_FCR0_CMD0_SHIFT) |
+ (NAND_CMD_ERASE2 << IFC_NAND_FCR0_CMD1_SHIFT));
+
+ out_be32(&ifc->ifc_nand.nand_fbcr, 0);
+ ifc_nand_ctrl->read_bytes = 0;
+ fsl_ifc_run_command(mtd);
+ return;
+
+ /* SEQIN sets up the addr buffer and all registers except the length */
+ case NAND_CMD_SEQIN: {
+ u32 nand_fcr0;
+ ifc_nand_ctrl->column = column;
+ ifc_nand_ctrl->oob = 0;
+
+ if (mtd->writesize > 512) {
+ nand_fcr0 =
+ (NAND_CMD_SEQIN << IFC_NAND_FCR0_CMD0_SHIFT) |
+ (NAND_CMD_PAGEPROG << IFC_NAND_FCR0_CMD1_SHIFT);
+
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP2_SHIFT) |
+ (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP3_SHIFT) |
+ (IFC_FIR_OP_CW1 << IFC_NAND_FIR0_OP4_SHIFT));
+ } else {
+ nand_fcr0 = ((NAND_CMD_PAGEPROG <<
+ IFC_NAND_FCR0_CMD1_SHIFT) |
+ (NAND_CMD_SEQIN <<
+ IFC_NAND_FCR0_CMD2_SHIFT));
+
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_CMD2 << IFC_NAND_FIR0_OP1_SHIFT) |
+ (IFC_FIR_OP_CA0 << IFC_NAND_FIR0_OP2_SHIFT) |
+ (IFC_FIR_OP_RA0 << IFC_NAND_FIR0_OP3_SHIFT) |
+ (IFC_FIR_OP_WBCD << IFC_NAND_FIR0_OP4_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fir1,
+ (IFC_FIR_OP_CW1 << IFC_NAND_FIR1_OP5_SHIFT));
+
+ if (column >= mtd->writesize)
+ nand_fcr0 |=
+ NAND_CMD_READOOB << IFC_NAND_FCR0_CMD0_SHIFT;
+ else
+ nand_fcr0 |=
+ NAND_CMD_READ0 << IFC_NAND_FCR0_CMD0_SHIFT;
+ }
+
+ if (column >= mtd->writesize) {
+ /* OOB area --> READOOB */
+ column -= mtd->writesize;
+ ifc_nand_ctrl->oob = 1;
+ }
+ out_be32(&ifc->ifc_nand.nand_fcr0, nand_fcr0);
+ set_addr(mtd, column, page_addr, ifc_nand_ctrl->oob);
+ return;
+ }
+
+ /* PAGEPROG reuses all of the setup from SEQIN and adds the length */
+ case NAND_CMD_PAGEPROG: {
+ if (ifc_nand_ctrl->oob) {
+ out_be32(&ifc->ifc_nand.nand_fbcr,
+ ifc_nand_ctrl->index - ifc_nand_ctrl->column);
+ } else {
+ out_be32(&ifc->ifc_nand.nand_fbcr, 0);
+ }
+
+ fsl_ifc_run_command(mtd);
+ return;
+ }
+
+ case NAND_CMD_STATUS:
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_RB << IFC_NAND_FIR0_OP1_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ NAND_CMD_STATUS << IFC_NAND_FCR0_CMD0_SHIFT);
+ out_be32(&ifc->ifc_nand.nand_fbcr, 1);
+ set_addr(mtd, 0, 0, 0);
+ ifc_nand_ctrl->read_bytes = 1;
+
+ fsl_ifc_run_command(mtd);
+
+ /*
+ * The chip always seems to report that it is
+ * write-protected, even when it is not.
+ */
+ setbits8(ifc_nand_ctrl->addr, NAND_STATUS_WP);
+ return;
+
+ case NAND_CMD_RESET:
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT);
+ out_be32(&ifc->ifc_nand.nand_fcr0,
+ NAND_CMD_RESET << IFC_NAND_FCR0_CMD0_SHIFT);
+ fsl_ifc_run_command(mtd);
+ return;
+
+ default:
+ dev_err(priv->dev, "%s: error, unsupported command 0x%x.\n",
+ __func__, command);
+ }
+}
+
+static void fsl_ifc_select_chip(struct mtd_info *mtd, int chip)
+{
+ /* The hardware does not seem to support multiple
+ * chips per bank.
+ */
+}
+
+/*
+ * Write buf to the IFC NAND Controller Data Buffer
+ */
+static void fsl_ifc_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ unsigned int bufsize = mtd->writesize + mtd->oobsize;
+
+ if (len <= 0) {
+ dev_err(priv->dev, "%s: len %d bytes", __func__, len);
+ return;
+ }
+
+ if ((unsigned int)len > bufsize - ifc_nand_ctrl->index) {
+ dev_err(priv->dev,
+ "%s: beyond end of buffer (%d requested, %u available)\n",
+ __func__, len, bufsize - ifc_nand_ctrl->index);
+ len = bufsize - ifc_nand_ctrl->index;
+ }
+
+ memcpy_toio(&ifc_nand_ctrl->addr[ifc_nand_ctrl->index], buf, len);
+ ifc_nand_ctrl->index += len;
+}
+
+/*
+ * Read a byte from either the IFC hardware buffer
+ * read function for 8-bit buswidth
+ */
+static uint8_t fsl_ifc_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+
+ /*
+ * If there are still bytes in the IFC buffer, then use the
+ * next byte.
+ */
+ if (ifc_nand_ctrl->index < ifc_nand_ctrl->read_bytes)
+ return in_8(&ifc_nand_ctrl->addr[ifc_nand_ctrl->index++]);
+
+ dev_err(priv->dev, "%s: beyond end of buffer\n", __func__);
+ return ERR_BYTE;
+}
+
+/*
+ * Read two bytes from the IFC hardware buffer
+ * read function for 16-bit buswith
+ */
+static uint8_t fsl_ifc_read_byte16(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ uint16_t data;
+
+ /*
+ * If there are still bytes in the IFC buffer, then use the
+ * next byte.
+ */
+ if (ifc_nand_ctrl->index < ifc_nand_ctrl->read_bytes) {
+ data = in_be16((uint16_t *)&ifc_nand_ctrl->
+ addr[ifc_nand_ctrl->index]);
+ ifc_nand_ctrl->index += 2;
+ return (uint8_t) data;
+ }
+
+ dev_err(priv->dev, "%s: beyond end of buffer\n", __func__);
+ return ERR_BYTE;
+}
+
+/*
+ * Read from the IFC Controller Data Buffer
+ */
+static void fsl_ifc_read_buf(struct mtd_info *mtd, u8 *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ int avail;
+
+ if (len < 0) {
+ dev_err(priv->dev, "%s: len %d bytes", __func__, len);
+ return;
+ }
+
+ avail = min((unsigned int)len,
+ ifc_nand_ctrl->read_bytes - ifc_nand_ctrl->index);
+ memcpy_fromio(buf, &ifc_nand_ctrl->addr[ifc_nand_ctrl->index], avail);
+ ifc_nand_ctrl->index += avail;
+
+ if (len > avail)
+ dev_err(priv->dev,
+ "%s: beyond end of buffer (%d requested, %d available)\n",
+ __func__, len, avail);
+}
+
+/*
+ * Verify buffer against the IFC Controller Data Buffer
+ */
+static int fsl_ifc_verify_buf(struct mtd_info *mtd,
+ const u_char *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_nand_ctrl *nctrl = ifc_nand_ctrl;
+ int i;
+
+ if (len < 0) {
+ dev_err(priv->dev, "%s: write_buf of %d bytes", __func__, len);
+ return -EINVAL;
+ }
+
+ if ((unsigned int)len > nctrl->read_bytes - nctrl->index) {
+ dev_err(priv->dev,
+ "%s: beyond end of buffer (%d requested, %u available)\n",
+ __func__, len, nctrl->read_bytes - nctrl->index);
+
+ nctrl->index = nctrl->read_bytes;
+ return -EINVAL;
+ }
+
+ for (i = 0; i < len; i++)
+ if (in_8(&nctrl->addr[nctrl->index + i]) != buf[i])
+ break;
+
+ nctrl->index += len;
+
+ if (i != len)
+ return -EIO;
+ if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC)
+ return -EIO;
+
+ return 0;
+}
+
+/*
+ * This function is called after Program and Erase Operations to
+ * check for success or failure.
+ */
+static int fsl_ifc_wait(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+ u32 nand_fsr;
+
+ /* Use READ_STATUS command, but wait for the device to be ready */
+ out_be32(&ifc->ifc_nand.nand_fir0,
+ (IFC_FIR_OP_CW0 << IFC_NAND_FIR0_OP0_SHIFT) |
+ (IFC_FIR_OP_RDSTAT << IFC_NAND_FIR0_OP1_SHIFT));
+ out_be32(&ifc->ifc_nand.nand_fcr0, NAND_CMD_STATUS <<
+ IFC_NAND_FCR0_CMD0_SHIFT);
+ out_be32(&ifc->ifc_nand.nand_fbcr, 1);
+ set_addr(mtd, 0, 0, 0);
+ ifc_nand_ctrl->read_bytes = 1;
+
+ fsl_ifc_run_command(mtd);
+
+ nand_fsr = in_be32(&ifc->ifc_nand.nand_fsr);
+
+ /*
+ * The chip always seems to report that it is
+ * write-protected, even when it is not.
+ */
+ return nand_fsr | NAND_STATUS_WP;
+}
+
+static int fsl_ifc_read_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ uint8_t *buf, int page)
+{
+ struct fsl_ifc_mtd *priv = chip->priv;
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+
+ fsl_ifc_read_buf(mtd, buf, mtd->writesize);
+ fsl_ifc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_ECCER)
+ dev_err(priv->dev, "NAND Flash ECC Uncorrectable Error\n");
+
+ if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC)
+ mtd->ecc_stats.failed++;
+
+ return 0;
+}
+
+/* ECC will be calculated automatically, and errors will be detected in
+ * waitfunc.
+ */
+static void fsl_ifc_write_page(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf)
+{
+ fsl_ifc_write_buf(mtd, buf, mtd->writesize);
+ fsl_ifc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
+}
+
+static int fsl_ifc_chip_init_tail(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct fsl_ifc_mtd *priv = chip->priv;
+
+ dev_dbg(priv->dev, "%s: nand->numchips = %d\n", __func__,
+ chip->numchips);
+ dev_dbg(priv->dev, "%s: nand->chipsize = %lld\n", __func__,
+ chip->chipsize);
+ dev_dbg(priv->dev, "%s: nand->pagemask = %8x\n", __func__,
+ chip->pagemask);
+ dev_dbg(priv->dev, "%s: nand->chip_delay = %d\n", __func__,
+ chip->chip_delay);
+ dev_dbg(priv->dev, "%s: nand->badblockpos = %d\n", __func__,
+ chip->badblockpos);
+ dev_dbg(priv->dev, "%s: nand->chip_shift = %d\n", __func__,
+ chip->chip_shift);
+ dev_dbg(priv->dev, "%s: nand->page_shift = %d\n", __func__,
+ chip->page_shift);
+ dev_dbg(priv->dev, "%s: nand->phys_erase_shift = %d\n", __func__,
+ chip->phys_erase_shift);
+ dev_dbg(priv->dev, "%s: nand->ecclayout = %p\n", __func__,
+ chip->ecclayout);
+ dev_dbg(priv->dev, "%s: nand->ecc.mode = %d\n", __func__,
+ chip->ecc.mode);
+ dev_dbg(priv->dev, "%s: nand->ecc.steps = %d\n", __func__,
+ chip->ecc.steps);
+ dev_dbg(priv->dev, "%s: nand->ecc.bytes = %d\n", __func__,
+ chip->ecc.bytes);
+ dev_dbg(priv->dev, "%s: nand->ecc.total = %d\n", __func__,
+ chip->ecc.total);
+ dev_dbg(priv->dev, "%s: nand->ecc.layout = %p\n", __func__,
+ chip->ecc.layout);
+ dev_dbg(priv->dev, "%s: mtd->flags = %08x\n", __func__, mtd->flags);
+ dev_dbg(priv->dev, "%s: mtd->size = %lld\n", __func__, mtd->size);
+ dev_dbg(priv->dev, "%s: mtd->erasesize = %d\n", __func__,
+ mtd->erasesize);
+ dev_dbg(priv->dev, "%s: mtd->writesize = %d\n", __func__,
+ mtd->writesize);
+ dev_dbg(priv->dev, "%s: mtd->oobsize = %d\n", __func__,
+ mtd->oobsize);
+
+ return 0;
+}
+
+static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
+{
+ struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ struct fsl_ifc_regs __iomem *ifc = ctrl->regs;
+ struct nand_chip *chip = &priv->chip;
+ struct nand_ecclayout *layout;
+ u32 csor;
+
+ /* Fill in fsl_ifc_mtd structure */
+ priv->mtd.priv = chip;
+ priv->mtd.owner = THIS_MODULE;
+
+ /* fill in nand_chip structure */
+ /* set up function call table */
+ if ((in_be32(&ifc->cspr_cs[priv->bank].cspr)) & CSPR_PORT_SIZE_16)
+ chip->read_byte = fsl_ifc_read_byte16;
+ else
+ chip->read_byte = fsl_ifc_read_byte;
+
+ chip->write_buf = fsl_ifc_write_buf;
+ chip->read_buf = fsl_ifc_read_buf;
+ chip->verify_buf = fsl_ifc_verify_buf;
+ chip->select_chip = fsl_ifc_select_chip;
+ chip->cmdfunc = fsl_ifc_cmdfunc;
+ chip->waitfunc = fsl_ifc_wait;
+
+ chip->bbt_td = &bbt_main_descr;
+ chip->bbt_md = &bbt_mirror_descr;
+
+ out_be32(&ifc->ifc_nand.ncfgr, 0x0);
+
+ /* set up nand options */
+ chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
+ chip->bbt_options = NAND_BBT_USE_FLASH;
+
+
+ if (in_be32(&ifc->cspr_cs[priv->bank].cspr) & CSPR_PORT_SIZE_16) {
+ chip->read_byte = fsl_ifc_read_byte16;
+ chip->options |= NAND_BUSWIDTH_16;
+ } else {
+ chip->read_byte = fsl_ifc_read_byte;
+ }
+
+ chip->controller = &ifc_nand_ctrl->controller;
+ chip->priv = priv;
+
+ chip->ecc.read_page = fsl_ifc_read_page;
+ chip->ecc.write_page = fsl_ifc_write_page;
+
+ csor = in_be32(&ifc->csor_cs[priv->bank].csor);
+
+ /* Hardware generates ECC per 512 Bytes */
+ chip->ecc.size = 512;
+ chip->ecc.bytes = 8;
+
+ switch (csor & CSOR_NAND_PGS_MASK) {
+ case CSOR_NAND_PGS_512:
+ if (chip->options & NAND_BUSWIDTH_16) {
+ layout = &oob_512_16bit_ecc4;
+ } else {
+ layout = &oob_512_8bit_ecc4;
+
+ /* Avoid conflict with bad block marker */
+ bbt_main_descr.offs = 0;
+ bbt_mirror_descr.offs = 0;
+ }
+
+ priv->bufnum_mask = 15;
+ break;
+
+ case CSOR_NAND_PGS_2K:
+ layout = &oob_2048_ecc4;
+ priv->bufnum_mask = 3;
+ break;
+
+ case CSOR_NAND_PGS_4K:
+ if ((csor & CSOR_NAND_ECC_MODE_MASK) ==
+ CSOR_NAND_ECC_MODE_4) {
+ layout = &oob_4096_ecc4;
+ } else {
+ layout = &oob_4096_ecc8;
+ chip->ecc.bytes = 16;
+ }
+
+ priv->bufnum_mask = 1;
+ break;
+
+ default:
+ dev_err(priv->dev, "bad csor %#x: bad page size\n", csor);
+ return -ENODEV;
+ }
+
+ /* Must also set CSOR_NAND_ECC_ENC_EN if DEC_EN set */
+ if (csor & CSOR_NAND_ECC_DEC_EN) {
+ chip->ecc.mode = NAND_ECC_HW;
+ chip->ecc.layout = layout;
+ } else {
+ chip->ecc.mode = NAND_ECC_SOFT;
+ }
+
+ return 0;
+}
+
+static int fsl_ifc_chip_remove(struct fsl_ifc_mtd *priv)
+{
+ nand_release(&priv->mtd);
+
+ kfree(priv->mtd.name);
+
+ if (priv->vbase)
+ iounmap(priv->vbase);
+
+ ifc_nand_ctrl->chips[priv->bank] = NULL;
+ dev_set_drvdata(priv->dev, NULL);
+ kfree(priv);
+
+ return 0;
+}
+
+static int match_bank(struct fsl_ifc_regs __iomem *ifc, int bank,
+ phys_addr_t addr)
+{
+ u32 cspr = in_be32(&ifc->cspr_cs[bank].cspr);
+
+ if (!(cspr & CSPR_V))
+ return 0;
+ if ((cspr & CSPR_MSEL) != CSPR_MSEL_NAND)
+ return 0;
+
+ return (cspr & CSPR_BA) == convert_ifc_address(addr);
+}
+
+static DEFINE_MUTEX(fsl_ifc_nand_mutex);
+
+static int __devinit fsl_ifc_nand_probe(struct platform_device *dev)
+{
+ struct fsl_ifc_regs __iomem *ifc;
+ struct fsl_ifc_mtd *priv;
+ struct resource res;
+ static const char *part_probe_types[]
+ = { "cmdlinepart", "RedBoot", "ofpart", NULL };
+ int ret;
+ int bank;
+ struct device_node *node = dev->dev.of_node;
+ struct mtd_part_parser_data ppdata;
+
+ ppdata.of_node = dev->dev.of_node;
+ if (!fsl_ifc_ctrl_dev || !fsl_ifc_ctrl_dev->regs)
+ return -ENODEV;
+ ifc = fsl_ifc_ctrl_dev->regs;
+
+ /* get, allocate and map the memory resource */
+ ret = of_address_to_resource(node, 0, &res);
+ if (ret) {
+ dev_err(&dev->dev, "%s: failed to get resource\n", __func__);
+ return ret;
+ }
+
+ /* find which chip select it is connected to */
+ for (bank = 0; bank < FSL_IFC_BANK_COUNT; bank++) {
+ if (match_bank(ifc, bank, res.start))
+ break;
+ }
+
+ if (bank >= FSL_IFC_BANK_COUNT) {
+ dev_err(&dev->dev, "%s: address did not match any chip selects\n",
+ __func__);
+ return -ENODEV;
+ }
+
+ priv = devm_kzalloc(&dev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ mutex_lock(&fsl_ifc_nand_mutex);
+ if (!fsl_ifc_ctrl_dev->nand) {
+ ifc_nand_ctrl = kzalloc(sizeof(*ifc_nand_ctrl), GFP_KERNEL);
+ if (!ifc_nand_ctrl) {
+ dev_err(&dev->dev, "failed to allocate memory\n");
+ mutex_unlock(&fsl_ifc_nand_mutex);
+ return -ENOMEM;
+ }
+
+ ifc_nand_ctrl->read_bytes = 0;
+ ifc_nand_ctrl->index = 0;
+ ifc_nand_ctrl->addr = NULL;
+ fsl_ifc_ctrl_dev->nand = ifc_nand_ctrl;
+
+ spin_lock_init(&ifc_nand_ctrl->controller.lock);
+ init_waitqueue_head(&ifc_nand_ctrl->controller.wq);
+ } else {
+ ifc_nand_ctrl = fsl_ifc_ctrl_dev->nand;
+ }
+ mutex_unlock(&fsl_ifc_nand_mutex);
+
+ ifc_nand_ctrl->chips[bank] = priv;
+ priv->bank = bank;
+ priv->ctrl = fsl_ifc_ctrl_dev;
+ priv->dev = &dev->dev;
+
+ priv->vbase = ioremap(res.start, resource_size(&res));
+ if (!priv->vbase) {
+ dev_err(priv->dev, "%s: failed to map chip region\n", __func__);
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ dev_set_drvdata(priv->dev, priv);
+
+ out_be32(&ifc->ifc_nand.nand_evter_en,
+ IFC_NAND_EVTER_EN_OPC_EN |
+ IFC_NAND_EVTER_EN_FTOER_EN |
+ IFC_NAND_EVTER_EN_WPER_EN);
+
+ /* enable NAND Machine Interrupts */
+ out_be32(&ifc->ifc_nand.nand_evter_intr_en,
+ IFC_NAND_EVTER_INTR_OPCIR_EN |
+ IFC_NAND_EVTER_INTR_FTOERIR_EN |
+ IFC_NAND_EVTER_INTR_WPERIR_EN);
+
+ priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start);
+ if (!priv->mtd.name) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ret = fsl_ifc_chip_init(priv);
+ if (ret)
+ goto err;
+
+ ret = nand_scan_ident(&priv->mtd, 1, NULL);
+ if (ret)
+ goto err;
+
+ ret = fsl_ifc_chip_init_tail(&priv->mtd);
+ if (ret)
+ goto err;
+
+ ret = nand_scan_tail(&priv->mtd);
+ if (ret)
+ goto err;
+
+ /* First look for RedBoot table or partitions on the command
+ * line, these take precedence over device tree information */
+ mtd_device_parse_register(&priv->mtd, part_probe_types, &ppdata,
+ NULL, 0);
+
+ dev_info(priv->dev, "IFC NAND device at 0x%llx, bank %d\n",
+ (unsigned long long)res.start, priv->bank);
+ return 0;
+
+err:
+ fsl_ifc_chip_remove(priv);
+ return ret;
+}
+
+static int fsl_ifc_nand_remove(struct platform_device *dev)
+{
+ struct fsl_ifc_mtd *priv = dev_get_drvdata(&dev->dev);
+
+ fsl_ifc_chip_remove(priv);
+
+ mutex_lock(&fsl_ifc_nand_mutex);
+ ifc_nand_ctrl->counter--;
+ if (!ifc_nand_ctrl->counter) {
+ fsl_ifc_ctrl_dev->nand = NULL;
+ kfree(ifc_nand_ctrl);
+ }
+ mutex_unlock(&fsl_ifc_nand_mutex);
+
+ return 0;
+}
+
+static const struct of_device_id fsl_ifc_nand_match[] = {
+ {
+ .compatible = "fsl,ifc-nand",
+ },
+ {}
+};
+
+static struct platform_driver fsl_ifc_nand_driver = {
+ .driver = {
+ .name = "fsl,ifc-nand",
+ .owner = THIS_MODULE,
+ .of_match_table = fsl_ifc_nand_match,
+ },
+ .probe = fsl_ifc_nand_probe,
+ .remove = fsl_ifc_nand_remove,
+};
+
+static int __init fsl_ifc_nand_init(void)
+{
+ int ret;
+
+ ret = platform_driver_register(&fsl_ifc_nand_driver);
+ if (ret)
+ printk(KERN_ERR "fsl-ifc: Failed to register platform"
+ "driver\n");
+
+ return ret;
+}
+
+static void __exit fsl_ifc_nand_exit(void)
+{
+ platform_driver_unregister(&fsl_ifc_nand_driver);
+}
+
+module_init(fsl_ifc_nand_init);
+module_exit(fsl_ifc_nand_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Freescale");
+MODULE_DESCRIPTION("Freescale Integrated Flash Controller MTD NAND driver");
--
1.7.5.4
More information about the Linuxppc-dev
mailing list