[PATCH 2/2 v3] powerpc/dts: Add dts for p1025rdb board
Zhicheng Fan
B32736 at freescale.com
Fri Feb 10 21:18:16 EST 2012
From: Zhicheng Fan <b32736 at freescale.com>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736 at freescale.com>
---
arch/powerpc/boot/dts/p1025rdb.dtsi | 286 ++++++++++++++++++++++++++++++++
arch/powerpc/boot/dts/p1025rdb_32b.dts | 137 +++++++++++++++
arch/powerpc/boot/dts/p1025rdb_36b.dts | 88 ++++++++++
3 files changed, 511 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1025rdb.dtsi
create mode 100644 arch/powerpc/boot/dts/p1025rdb_32b.dts
create mode 100644 arch/powerpc/boot/dts/p1025rdb_36b.dts
diff --git a/arch/powerpc/boot/dts/p1025rdb.dtsi b/arch/powerpc/boot/dts/p1025rdb.dtsi
new file mode 100644
index 0000000..cf3676f
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb.dtsi
@@ -0,0 +1,286 @@
+/*
+ * P1025 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor at 0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition at 0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition at 40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR DTB Image";
+ };
+
+ partition at 80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR Linux Kernel Image";
+ };
+
+ partition at 400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR JFFS2 Root File System";
+ };
+
+ partition at f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand at 1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1025-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition at 0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition at 100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition at 200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition at 600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND Compressed RFS Image";
+ };
+
+ partition at a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND JFFS2 Root File System";
+ };
+
+ partition at 1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND Writable User area";
+ };
+ };
+
+};
+
+&soc {
+ i2c at 3000 {
+ rtc at 68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+ };
+
+ spi at 7000 {
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition at u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition at dtb {
+ /* 512KB for DTB Image */
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ };
+
+ partition at kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ };
+
+ partition at fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ };
+
+ partition at jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb at 22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb at 23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio at 25000 {
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio at 26000 {
+ tbi2: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ par_io at e0100 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xe0100 0x60>;
+ ranges = <0x0 0xe0100 0x60>;
+ device_type = "par_io";
+ num-ports = <3>;
+ pio1: ucc_pin at 01 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
+ 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
+ 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
+ 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
+ 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
+ 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
+ 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
+ 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
+ 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
+ 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
+ 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
+ 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
+ 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
+ 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
+ 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
+ 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
+ };
+
+ pio2: ucc_pin at 02 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
+ 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
+ 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
+ 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
+ 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
+ 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
+ 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
+ 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1025rdb_32b.dts b/arch/powerpc/boot/dts/p1025rdb_32b.dts
new file mode 100644
index 0000000..b0ffc13
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb_32b.dts
@@ -0,0 +1,137 @@
+/*
+ * P1025 RDB Device Tree Source (32-bit address map)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1021si-pre.dtsi"
+/ {
+ model = "fsl,P1025RDB";
+ compatible = "fsl,P1025RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus at ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes */
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000>;
+ };
+
+ soc: soc at ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie at ffe09000 {
+ ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie at ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe: qe at ffe80000 {
+ ranges = <0x0 0x0 0xffe80000 0x40000>;
+ reg = <0 0xffe80000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+ status = "disabled"; /* no firmware loaded */
+
+ enet3: ucc at 2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "clk12";
+ tx-clock-name = "clk9";
+ pio-handle = <&pio1>;
+ phy-handle = <&qe_phy0>;
+ phy-connection-type = "mii";
+ };
+
+ mdio at 2120 {
+ qe_phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <4 1 0 0>;
+ reg = <0x6>;
+ device_type = "ethernet-phy";
+ };
+ qe_phy1: ethernet-phy at 03 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1 0 0>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet4: ucc at 2400 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "none";
+ tx-clock-name = "clk13";
+ pio-handle = <&pio2>;
+ phy-handle = <&qe_phy1>;
+ phy-connection-type = "rmii";
+ };
+ };
+};
+
+/include/ "p1025rdb.dtsi"
+/include/ "fsl/p1021si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1025rdb_36b.dts b/arch/powerpc/boot/dts/p1025rdb_36b.dts
new file mode 100644
index 0000000..4ce4bfa
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb_36b.dts
@@ -0,0 +1,88 @@
+/*
+ * P1025 RDB Device Tree Source (36-bit address map)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1021si-pre.dtsi"
+/ {
+ model = "fsl,P1025RDB";
+ compatible = "fsl,P1025RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus at fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000>;
+ };
+
+ soc: soc at fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie at fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0xe 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie at fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1025rdb.dtsi"
+/include/ "fsl/p1021si-post.dtsi"
--
1.7.0.4
More information about the Linuxppc-dev
mailing list