[RFC][PATCH 2/2] powerpc/85xx: Introduce a P1020 SoC device tree
Kumar Gala
galak at kernel.crashing.org
Thu Oct 20 18:24:26 EST 2011
Create a P1020 SoC dts stub that can be included by a board that
utilizes the P1020 SoC. The board can amend any board specific
configuration or paramaters (like locaation of CCSRBAR, PCIe
controllers, I2C components, ethernet PHY information, etc.)
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
arch/powerpc/boot/dts/p1020soc.dtsi | 262 +++++++++++++++++++++++++++++++++++
1 files changed, 262 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020soc.dtsi
diff --git a/arch/powerpc/boot/dts/p1020soc.dtsi b/arch/powerpc/boot/dts/p1020soc.dtsi
new file mode 100644
index 0000000..0abc015
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020soc.dtsi
@@ -0,0 +1,262 @@
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1
+ >;
+ };
+
+};
+
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1
+ >;
+ };
+};
+
+
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1020-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law at 0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm at 1000 {
+ compatible = "fsl,p1020-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller at 2000 {
+ compatible = "fsl,p1020-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ i2c0: i2c at 3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2 0 0>;
+ dfsrr;
+ };
+
+ i2c1: i2c at 3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2 0 0>;
+ dfsrr;
+ };
+
+ serial0: serial at 4500 {
+ };
+
+ serial1: serial at 4600 {
+ };
+
+ spi at 7000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,p1020-espi", "fsl,mpc8536-espi";
+ reg = <0x7000 0x1000>;
+ interrupts = <59 0x2 0 0>;
+ fsl,espi-num-chipselects = <4>;
+ };
+
+ gpio: gpio-controller at f000 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8572-gpio";
+ reg = <0xf000 0x100>;
+ interrupts = <47 0x2 0 0>;
+ gpio-controller;
+ };
+
+ L2: l2-cache-controller at 20000 {
+ compatible = "fsl,p1020-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+ dma0: dma at 21300 {
+ };
+
+ mdio0: mdio at 24000 {
+ };
+
+ mdio1: mdio at 25000 {
+ };
+
+ mdio2: mdio at 26000 {
+ };
+
+ enet0: ethernet at b0000 {
+ };
+
+ enet1: ethernet at b1000 {
+ };
+
+ enet2: ethernet at b2000 {
+ };
+
+ usb at 22000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl-usb2-dr";
+ reg = <0x22000 0x1000>;
+ interrupts = <28 0x2 0 0>;
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb at 23000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl-usb2-dr";
+ reg = <0x23000 0x1000>;
+ interrupts = <46 0x2 0 0>;
+ phy_type = "ulpi";
+ };
+ */
+
+ sdhci at 2e000 {
+ compatible = "fsl,p1020-esdhc", "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <72 0x2 0 0>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
+ };
+
+ crypto at 30000 {
+ compatible = "fsl,sec3.3", "fsl,sec3.1", "fsl,sec3.0",
+ "fsl,sec2.4", "fsl,sec2.2", "fsl,sec2.1",
+ "fsl,sec2.0";
+ reg = <0x30000 0x10000>;
+ interrupts = <45 2 0 0 58 2 0 0>;
+ fsl,num-channels = <4>;
+ fsl,channel-fifo-len = <24>;
+ fsl,exec-units-mask = <0x97c>;
+ fsl,descriptor-types-mask = <0x3a30abf>;
+ };
+
+ mpic: pic at 40000 {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <4>;
+ reg = <0x40000 0x40000>;
+ compatible = "chrp,open-pic";
+ device_type = "open-pic";
+ };
+
+ timer at 41100 {
+ compatible = "fsl,mpic-global-timer";
+ reg = <0x41100 0x100 0x41300 4>;
+ interrupts = <0 0 3 0
+ 1 0 3 0
+ 2 0 3 0
+ 3 0 3 0>;
+ };
+
+ timer at 42100 {
+ compatible = "fsl,mpic-global-timer";
+ reg = <0x42100 0x100 0x42300 4>;
+ interrupts = <4 0 3 0
+ 5 0 3 0
+ 6 0 3 0
+ 7 0 3 0>;
+ };
+
+ msi at 41600 {
+ compatible = "fsl,p1020-msi", "fsl,mpic-msi";
+ reg = <0x41600 0x80>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe0 0 0 0
+ 0xe1 0 0 0
+ 0xe2 0 0 0
+ 0xe3 0 0 0
+ 0xe4 0 0 0
+ 0xe5 0 0 0
+ 0xe6 0 0 0
+ 0xe7 0 0 0>;
+ };
+
+ global-utilities at e0000 { //global utilities block
+ compatible = "fsl,p1020-guts","fsl,p2020-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
+
+/include/ "fsl/pq3-dma-0.dtsi"
+/include/ "fsl/pq3-duart-0.dtsi"
+/include/ "fsl/pq3-duart-1.dtsi"
+/include/ "fsl/pq3-etsec2-0.dtsi"
+/include/ "fsl/pq3-etsec2-1.dtsi"
+/include/ "fsl/pq3-etsec2-2.dtsi"
+/include/ "fsl/pq3-i2c-0.dtsi"
+/include/ "fsl/pq3-i2c-1.dtsi"
--
1.7.3.4
More information about the Linuxppc-dev
mailing list