[PATCH 1/5][v2] powerpc/fsl: Document rapidio node binding-information
Kumar Gala
galak at kernel.crashing.org
Fri Oct 14 01:08:38 EST 2011
From: Liu Gang <Gang.Liu at freescale.com>
This document is created for powerpc rapidio and rmu nodes in dts file.
These nodes can support two rapidio ports and message units. In addition,
It explicates the properties and gives examples about rapidio and rmu nodes.
Signed-off-by: Li Yang <leoli at freescale.com>
Signed-off-by: Jin Qing <b24347 at freescale.com>
Signed-off-by: Liu Gang <Gang.Liu at freescale.com>
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
.../devicetree/bindings/powerpc/fsl/srio-rmu.txt | 163 ++++++++++++++++++++
.../devicetree/bindings/powerpc/fsl/srio.txt | 103 ++++++++++++
2 files changed, 266 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
create mode 100644 Documentation/devicetree/bindings/powerpc/fsl/srio.txt
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
new file mode 100644
index 0000000..b9a8a2b
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
@@ -0,0 +1,163 @@
+Message unit node:
+
+For SRIO controllers that implement the message unit as part of the controller
+this node is required. For devices with RMAN this node should NOT exist. The
+node is composed of three types of sub-nodes ("fsl-srio-msg-unit",
+"fsl-srio-dbell-unit" and "fsl-srio-port-write-unit").
+
+See srio.txt for more details about generic SRIO controller details.
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio-rmu-vX.Y", "fsl,srio-rmu".
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - fsl,liodn
+ Usage: optional-but-recommended (for devices with PAMU)
+ Value type: <prop-encoded-array>
+ Definition: The logical I/O device number for the PAMU (IOMMU) to be
+ correctly configured for SRIO accesses. The property should
+ not exist on devices that do not support PAMU.
+
+ The LIODN value is associated with all RMU transactions
+ (msg-unit, doorbell, port-write).
+
+Sub-Nodes for RMU: The RMU node is composed of multiple sub-nodes that
+correspond to the actual sub-controllers in the RMU. The manual for a given
+SoC will detail which and how many of these sub-controllers are implemented.
+
+Message Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio-msg-unit-vX.Y", "fsl,srio-msg-unit".
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A pair of IRQs are specified in this property. The first
+ element is associated with the transmit (TX) interrupt and the
+ second element is associated with the receive (RX) interrupt.
+
+Doorbell Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include:
+ "fsl,srio-dbell-unit-vX.Y", "fsl,srio-dbell-unit"
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A pair of IRQs are specified in this property. The first
+ element is associated with the transmit (TX) interrupt and the
+ second element is associated with the receive (RX) interrupt.
+
+Port-Write Unit:
+
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include:
+ "fsl,srio-port-write-unit-vX.Y", "fsl,srio-port-write-unit"
+
+ The version X.Y should match the general SRIO controller's IP Block
+ revision register's Major(X) and Minor (Y) value.
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers for message units
+ and doorbell units.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A single IRQ that handles port-write conditions is
+ specified by this property. (Typically shared with error).
+
+ Note: All other standard properties (see the ePAPR) are allowed
+ but are optional.
+
+Example:
+ rmu: rmu at d3000 {
+ compatible = "fsl,srio-rmu";
+ reg = <0xd3000 0x400>;
+ ranges = <0x0 0xd3000 0x400>;
+ fsl,liodn = <0xc8>;
+
+ message-unit at 0 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x0 0x100>;
+ interrupts = <
+ 60 2 0 0 /* msg1_tx_irq */
+ 61 2 0 0>;/* msg1_rx_irq */
+ };
+ message-unit at 100 {
+ compatible = "fsl,srio-msg-unit";
+ reg = <0x100 0x100>;
+ interrupts = <
+ 62 2 0 0 /* msg2_tx_irq */
+ 63 2 0 0>;/* msg2_rx_irq */
+ };
+ doorbell-unit at 400 {
+ compatible = "fsl,srio-dbell-unit";
+ reg = <0x400 0x80>;
+ interrupts = <
+ 56 2 0 0 /* bell_outb_irq */
+ 57 2 0 0>;/* bell_inb_irq */
+ };
+ port-write-unit at 4e0 {
+ compatible = "fsl,srio-port-write-unit";
+ reg = <0x4e0 0x20>;
+ interrupts = <16 2 1 11>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
new file mode 100644
index 0000000..b039bcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
@@ -0,0 +1,103 @@
+* Freescale Serial RapidIO (SRIO) Controller
+
+RapidIO port node:
+Properties:
+ - compatible
+ Usage: required
+ Value type: <string>
+ Definition: Must include "fsl,srio" for IP blocks with IP Block
+ Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0.
+
+ Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major
+ version in IP Block Revision Register and Y is Minor version. If this
+ compatiable is provided it should be ordered before "fsl,srio".
+
+ - reg
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Specifies the physical address and
+ length of the SRIO configuration registers. The size should
+ be set to 0x11000.
+
+ - interrupts
+ Usage: required
+ Value type: <prop_encoded-array>
+ Definition: Specifies the interrupts generated by this device. The
+ value of the interrupts property consists of one interrupt
+ specifier. The format of the specifier is defined by the
+ binding document describing the node's interrupt parent.
+
+ A single IRQ that handles error conditions is specified by this
+ property. (Typically shared with port-write).
+
+ - fsl,srio-rmu-handle:
+ Usage: required if rmu node is defined
+ Value type: <phandle>
+ Definition: A single <phandle> value that points to the RMU.
+ (See srio-rmu.txt for more details on RMU node binding)
+
+Port Child Nodes: There should a port child node for each port that exists in
+the controller. The ports are numbered starting at one (1) and should have
+the following properties:
+
+ - cell-index
+ Usage: required
+ Value type: <u32>
+ Definition: A standard property. Matches the port id.
+
+ - ranges
+ Usage: required if local access windows preset
+ Value type: <prop-encoded-array>
+ Definition: A standard property. Utilized to describe the memory mapped
+ IO space utilized by the controller. This corresponds to the
+ setting of the local access windows that are targeted to this
+ SRIO port.
+
+ - fsl,liodn
+ Usage: optional-but-recommended (for devices with PAMU)
+ Value type: <prop-encoded-array>
+ Definition: The logical I/O device number for the PAMU (IOMMU) to be
+ correctly configured for SRIO accesses. The property should
+ not exist on devices that do not support PAMU.
+
+ For HW (ie, the P4080) that only supports a LIODN for both
+ memory and maintenance transactions then a single LIODN is
+ represented in the property for both transactions.
+
+ For HW (ie, the P304x/P5020, etc) that supports an LIODN for
+ memory transactions and a unique LIODN for maintenance
+ transactions then a pair of LIODNs are represented in the
+ property. Within the pair, the first element represents the
+ LIODN associated with memory transactions and the second element
+ represents the LIODN associated with maintenance transactions
+ for the port.
+
+Note: All other standard properties (see ePAPR) are allowed but are optional.
+
+Example:
+
+ rapidio: rapidio at ffe0c0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0xf 0xfe0c0000 0 0x11000>;
+ compatible = "fsl,srio";
+ interrupts = <16 2 1 11>; /* err_irq */
+ fsl,srio-rmu-handle = <&rmu>;
+ ranges;
+
+ port1 {
+ cell-index = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ fsl,liodn = <34>;
+ ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+ };
+
+ port2 {
+ cell-index = <2>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ fsl,liodn = <48>;
+ ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+ };
+ };
--
1.7.3.4
More information about the Linuxppc-dev
mailing list