[RFC][PATCH 09/30] powerpc/85xx: Rework P1020RDB device tree
Kumar Gala
galak at kernel.crashing.org
Fri Nov 11 03:13:52 EST 2011
We split out the common bits of the P1020RDB device tree such that we
can reuse those bits between a 32-bit or 36-bit address map device tree.
We also update the P1020RDB device tree to utilize the new p1020 SoC dts
includes (fsl/p1020si-pre.dtsi & fsl/p1020si-post.dtsi).
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
arch/powerpc/boot/dts/p1020rdb.dts | 232 +--------------------------------
arch/powerpc/boot/dts/p1020rdb.dtsi | 242 +++++++++++++++++++++++++++++++++++
2 files changed, 250 insertions(+), 224 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020rdb.dtsi
diff --git a/arch/powerpc/boot/dts/p1020rdb.dts b/arch/powerpc/boot/dts/p1020rdb.dts
index b31e7ec..518bf99 100644
--- a/arch/powerpc/boot/dts/p1020rdb.dts
+++ b/arch/powerpc/boot/dts/p1020rdb.dts
@@ -9,245 +9,26 @@
* option) any later version.
*/
-/include/ "p1020si.dtsi"
-
+/include/ "fsl/p1020si-pre.dtsi"
/ {
model = "fsl,P1020RDB";
compatible = "fsl,P1020RDB";
- aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- ethernet0 = &enet0;
- ethernet1 = &enet1;
- ethernet2 = &enet2;
- pci0 = &pci0;
- pci1 = &pci1;
- };
-
memory {
device_type = "memory";
};
- localbus at ffe05000 {
+ board_lbc: lbc: localbus at ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
/* NOR, NAND Flashes and Vitesse 5 port L2 switch */
ranges = <0x0 0x0 0x0 0xef000000 0x01000000
0x1 0x0 0x0 0xffa00000 0x00040000
0x2 0x0 0x0 0xffb00000 0x00020000>;
-
- nor at 0,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "cfi-flash";
- reg = <0x0 0x0 0x1000000>;
- bank-width = <2>;
- device-width = <1>;
-
- partition at 0 {
- /* This location must not be altered */
- /* 256KB for Vitesse 7385 Switch firmware */
- reg = <0x0 0x00040000>;
- label = "NOR (RO) Vitesse-7385 Firmware";
- read-only;
- };
-
- partition at 40000 {
- /* 256KB for DTB Image */
- reg = <0x00040000 0x00040000>;
- label = "NOR (RO) DTB Image";
- read-only;
- };
-
- partition at 80000 {
- /* 3.5 MB for Linux Kernel Image */
- reg = <0x00080000 0x00380000>;
- label = "NOR (RO) Linux Kernel Image";
- read-only;
- };
-
- partition at 400000 {
- /* 11MB for JFFS2 based Root file System */
- reg = <0x00400000 0x00b00000>;
- label = "NOR (RW) JFFS2 Root File System";
- };
-
- partition at f00000 {
- /* This location must not be altered */
- /* 512KB for u-boot Bootloader Image */
- /* 512KB for u-boot Environment Variables */
- reg = <0x00f00000 0x00100000>;
- label = "NOR (RO) U-Boot Image";
- read-only;
- };
- };
-
- nand at 1,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,p1020-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg = <0x1 0x0 0x40000>;
-
- partition at 0 {
- /* This location must not be altered */
- /* 1MB for u-boot Bootloader Image */
- reg = <0x0 0x00100000>;
- label = "NAND (RO) U-Boot Image";
- read-only;
- };
-
- partition at 100000 {
- /* 1MB for DTB Image */
- reg = <0x00100000 0x00100000>;
- label = "NAND (RO) DTB Image";
- read-only;
- };
-
- partition at 200000 {
- /* 4MB for Linux Kernel Image */
- reg = <0x00200000 0x00400000>;
- label = "NAND (RO) Linux Kernel Image";
- read-only;
- };
-
- partition at 600000 {
- /* 4MB for Compressed Root file System Image */
- reg = <0x00600000 0x00400000>;
- label = "NAND (RO) Compressed RFS Image";
- read-only;
- };
-
- partition at a00000 {
- /* 7MB for JFFS2 based Root file System */
- reg = <0x00a00000 0x00700000>;
- label = "NAND (RW) JFFS2 Root File System";
- };
-
- partition at 1100000 {
- /* 15MB for JFFS2 based Root file System */
- reg = <0x01100000 0x00f00000>;
- label = "NAND (RW) Writable User area";
- };
- };
-
- L2switch at 2,0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "vitesse-7385";
- reg = <0x2 0x0 0x20000>;
- };
-
};
- soc at ffe00000 {
- i2c at 3000 {
- rtc at 68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
- };
- };
-
- spi at 7000 {
- flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "spansion,s25sl12801";
- reg = <0>;
- spi-max-frequency = <40000000>; /* input clock */
-
- partition at u-boot {
- /* 512KB for u-boot Bootloader Image */
- reg = <0x0 0x00080000>;
- label = "u-boot";
- read-only;
- };
-
- partition at dtb {
- /* 512KB for DTB Image */
- reg = <0x00080000 0x00080000>;
- label = "dtb";
- read-only;
- };
-
- partition at kernel {
- /* 4MB for Linux Kernel Image */
- reg = <0x00100000 0x00400000>;
- label = "kernel";
- read-only;
- };
-
- partition at fs {
- /* 4MB for Compressed RFS Image */
- reg = <0x00500000 0x00400000>;
- label = "file system";
- read-only;
- };
-
- partition at jffs-fs {
- /* 7MB for JFFS2 based RFS */
- reg = <0x00900000 0x00700000>;
- label = "file system jffs2";
- };
- };
- };
-
- mdio at 24000 {
-
- phy0: ethernet-phy at 0 {
- interrupt-parent = <&mpic>;
- interrupts = <3 1>;
- reg = <0x0>;
- };
-
- phy1: ethernet-phy at 1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x1>;
- };
- };
-
- mdio at 25000 {
-
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- enet0: ethernet at b0000 {
- fixed-link = <1 1 1000 0 0>;
- phy-connection-type = "rgmii-id";
-
- };
-
- enet1: ethernet at b1000 {
- phy-handle = <&phy0>;
- tbi-handle = <&tbi0>;
- phy-connection-type = "sgmii";
-
- };
-
- enet2: ethernet at b2000 {
- phy-handle = <&phy1>;
- phy-connection-type = "rgmii-id";
-
- };
-
- usb at 22000 {
- phy_type = "ulpi";
- };
-
- /* USB2 is shared with localbus, so it must be disabled
- by default. We can't put 'status = "disabled";' here
- since U-Boot doesn't clear the status property when
- it enables USB2. OTOH, U-Boot does create a new node
- when there isn't any. So, just comment it out.
- usb at 23000 {
- phy_type = "ulpi";
- };
- */
-
+ board_soc: soc: soc at ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
};
pci0: pcie at ffe09000 {
@@ -280,3 +61,6 @@
};
};
};
+
+/include/ "p1020rdb.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb.dtsi b/arch/powerpc/boot/dts/p1020rdb.dtsi
new file mode 100644
index 0000000..3738946
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb.dtsi
@@ -0,0 +1,242 @@
+/*
+ * P1020 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&board_lbc {
+ nor at 0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition at 0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR (RO) Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition at 40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR (RO) DTB Image";
+ read-only;
+ };
+
+ partition at 80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition at 400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR (RW) JFFS2 Root File System";
+ };
+
+ partition at f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR (RO) U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand at 1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition at 0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND (RO) U-Boot Image";
+ read-only;
+ };
+
+ partition at 100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND (RO) DTB Image";
+ read-only;
+ };
+
+ partition at 200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition at 600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND (RO) Compressed RFS Image";
+ read-only;
+ };
+
+ partition at a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND (RW) JFFS2 Root File System";
+ };
+
+ partition at 1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND (RW) Writable User area";
+ };
+ };
+
+ L2switch at 2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse-7385";
+ reg = <0x2 0x0 0x20000>;
+ };
+};
+
+&board_soc {
+ i2c at 3000 {
+ rtc at 68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+ };
+
+ spi at 7000 {
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition at u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition at dtb {
+ /* 512KB for DTB Image */
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ read-only;
+ };
+
+ partition at kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ read-only;
+ };
+
+ partition at fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ read-only;
+ };
+
+ partition at jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb at 22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb at 23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+ };
+
+ mdio at 25000 {
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet at b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi0>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet at b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
--
1.7.3.4
More information about the Linuxppc-dev
mailing list