How to define an I2C-to-SPI bridge device ?

[Andre Schwarz]

On 03/25/2011 10:28 AM, Andre Schwarz wrote:
> Grant, Anton,

got it.
providing modalis = "spidev" within spi_board_info works like a charme ...

Cheers,
André

>
>>>> we're about to get new MPC8377 based hardware with various 
>>>> peripherals.
>>>>> There are two I2C-to-SPI bridge devices (NXP SC18IS602) and I'm 
>>>>> not sure
>>>>> how to define a proper dts...
>>>>>
>>>>> Of course it's an easy thing creating 2 child nodes on the CPU's I2C
>>>>> device - but how can I represent the created SPI bus ?
>>>> Um.. the same as the other SPI buses? I.e.
>>>>
>>>> i2c-controller {  /* SOC I2C controller */
>>>>     spi-controller {  /* The I2C-to-SPI bridge */
>>>>         spi-device at 0 {
>>>>         };
>>>>         spi-device at 1 {
>>>>         };
>>>>     };
>>>> };
>>>>
>>> ok , thanks - looks straight forward.
>>> Is this any more than plain definition, i.e. will this trigger any I2C
>>> or SPI device registration/linking ?
>>>>> Is the (possibly) required driver (of_sc18is60x_spi ?) supposed to 
>>>>> be an
>>>>> I2C slave or an SPI host driver ?
>>>> It should be an I2C driver that registers an SPI master (i.e.
>>>> calls spi_alloc_master() and spi_register_master()).
>>> hmm - ok. Will have to do it manually then ...
>> Yes, but this is the case for non-of drivers too.  The i2c to spi 
>> device driver must always create (and trigger population of) the spi 
>> bus instance.
>>
>
> I've kicked that I2C-to-SPI stuff completely because it's been too slow.
> We've connected the SPI busses to the FPGA controlling almost 
> everything now.
>
> Unfortunately there are some questions left :
>
> Following Anton's suggestion I've had a look at /drivers/mfd (sm501.c) 
> and implemented a pci driver for the FPGA using
> subdevices for additional functionality it exports - besides others we 
> now have 2 SPI masters.
>
> For both SPI masters I have created and registered a platform_device.
> pdev->dev is then fed into spi_alloc_master() and the resulting master 
> goes into spi_register_master().
>
> master->bus_num is set to 0 and 1, i.e. no dynamic numbering.
> master->chipselect = 8;
>
> Since I can probe the SPI device using FPGA intrinsic information I 
> decided to register the client
> devices on runtime using a "struct spi_board_info" which is fed into 
> spi_new_device().
>
> The current design has 2 clients on SPI-0 and 5 clients on SPI-1.
>
> static struct spi_board_info mergerbox_spi_boardinfo[] = {
>         {       .bus_num = 0,
>                 .chip_select = 0,
>                 .max_speed_hz = 4<<20, },
>         {       .bus_num = 0,
>                 .chip_select = 1,
>                 .max_speed_hz = 4<<20, },
>         {       .bus_num = 1,
>                 .chip_select = 0,
>                 .max_speed_hz = 4<<20, },
> .....
>
>
> After loading my module I get :
>
> #> ls /sys/devices/platform/AlteraSPI.0/
> /sys/devices/platform/AlteraSPI.0/modalias
> /sys/devices/platform/AlteraSPI.0/spi0.0/
> /sys/devices/platform/AlteraSPI.0/spi0.1/
> /sys/devices/platform/AlteraSPI.0/spi_master/
> /sys/devices/platform/AlteraSPI.0/subsystem/
> /sys/devices/platform/AlteraSPI.0/uevent
>
> #> ls /sys/devices/platform/AlteraSPI.1/
> /sys/devices/platform/AlteraSPI.1/modalias
> /sys/devices/platform/AlteraSPI.1/spi1.0/
> /sys/devices/platform/AlteraSPI.1/spi1.1/
> /sys/devices/platform/AlteraSPI.1/spi1.2/
> /sys/devices/platform/AlteraSPI.1/spi1.3/
> /sys/devices/platform/AlteraSPI.1/spi1.4/
> /sys/devices/platform/AlteraSPI.1/spi_master/
> /sys/devices/platform/AlteraSPI.1/subsystem/
> /sys/devices/platform/AlteraSPI.1/uevent
>
> What I'm missing are the /dev/spi* entries.
>
> There's also a spi_mpc8xxx driver using the CPU's SPI controller.
> It is configured by dts (2 devices) and uses dynamic bus numbering:
>
> #> ls /sys/bus/spi/devices/
> spi0.0      spi1.0      spi1.2      spi1.4      spi32766.1
> spi0.1      spi1.1      spi1.3      spi32766.0
>
> This devices are processed by spidev and proper entries are created 
> ready for use :
>
> #> ls /dev/spi*
> /dev/spidev32766.0  /dev/spidev32766.1
>
>
> Am I missing somehting obvious ?
>
> Since there's no driver registration we don't have a probe function - 
> is this a problem regarding device binding ?
>
> Do I need to use the .modalias in "struct spi_board_info" ?
>
>
> Any help is welcome.
>
> Regards,
> André


MATRIX VISION GmbH, Talstrasse 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschaeftsfuehrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner