any chance to use a modern linux kernel on Pegasos1 G3 ?
nello martuscielli
ppc.addon at gmail.com
Wed Mar 16 03:44:49 EST 2011
ok, it seems that no one is interested to fix Pegasos1 G3 600MHz support.
But if someone is capable (i don't have this skill) here what it
happens reading from serial debug console untill it freezes with
linux-2.6.36.4
Pegasos Boot Strap (c) 2002 bplan GmbH
Running on CPU PVR:00083311
PLL setting : 00000001
Enable L1 ICache... Done.
Setting ROM Defaults... Done.
Configuring SDRAM...
08000000
10000000
Delaying...Done.
RAMSIZE = 18000000
00000004
Reading W83194 : 00FFFFFFFFFF0000 Done.
Setting Front Side Bus to 100MHz... Done.
Releasing IDE reset ... Done.
Configuring Legacy Devices
Initializing KBD... Done.
PLL setting : 00000003
10000000
Done.
FFFFFFFF
BIOS: Stage 2 entered arg(FFFC0000,00000000,18000000)
BIOS: MachineInfo at 0FFFFE68
BIOS: set MemPool limit to BAT size (old=18000000 new=10000000)
BIOS: 0F6FFFE8 bytes added to mempool
LoadFromRFS: starting
LoadFromRFS: lib module 00 has abs load adr at 00C00000
CopyModule: start
CopyModule: load address : 00C00000
CopyModule: copy module to ram...done
ModuleCopy: expanding... done
LoadFromRFS: 00000001 modules out of 00000001 loaded
InitLib: start
InitLib: call module as OF
allocated g_e=0xFD00008 (len=19232)
install_root: pkg=0xFD53B90
after init_environ e=0xFD00008
running nvramrc...
after running nvramrc
no/bad nvramrc - performing default startup script
Bus addresses:
253 at 2
I/O addresses:
7936 at FE002100
Memory addresses:
127M at 88040000
1.3G at 98000000
Prefetchable memory addresses:
install_ata_disk_driver: reg=0x1000
init_drive: reset controller 0x1000/0x100E
init_drive: allow 4-bits for heads
init_drive: select drive 0
init_drive: seccnt=0x1 sector=0x1 cyl_lo=0x0 cyl_hi=0x0
init_drive: error=0x1 status=0x50 status2=0x50
init_drive: identify drive: atapi=0
install_ata_disk_driver: return no error (0)
install_ata_disk_driver: reg=0x1000
init_drive: allow 4-bits for heads
init_drive: select drive 1
init_drive: seccnt=0x1 sector=0x1 cyl_lo=0x14 cyl_hi=0xEB
init_drive: error=0x1 status=0x0 status2=0x0
init_drive: identify drive: atapi=1
atapi_cmd: cmdlen=12
atapi_cmd: inlen=8 len=65534
install_ata_disk_driver: return no error (0)
install_ata_disk_driver: reg=0x1010
init_drive: reset controller 0x1010/0x101E
init_drive: allow 4-bits for heads
init_drive: select drive 0
init_drive: seccnt=0x20 sector=0x20 cyl_lo=0x20 cyl_hi=0x20
init_drive: error=0x20 status=0x20 status2=0x20
ATA-wait-ready: timeout: status=0x20
init_drive: failed
install_ata_disk_driver: reg=0x1010
init_drive: allow 4-bits for heads
init_drive: select drive 1
init_drive: seccnt=0x30 sector=0x30 cyl_lo=0x30 cyl_hi=0x30
init_drive: error=0x30 status=0x30 status2=0x30
ATA-wait-ready: timeout: status=0x30
init_drive: failed
Bus addresses:
254 at 2
I/O addresses:
8 at FE001038
3072 at FE001400
48K at FE004000
Memory addresses:
1792 at A0000100
1.2G at A0001000
Prefetchable memory addresses:
12M at FD400000
F_INSTALL_CONSOLE: BEGIN
F_INSTALL_CONSOLE: ALIASING SCREEN
F_INSTALL_CONSOLE: ALIASING KBD
EMULATION INT HANDLER ENTERED WITH:
INT NO: 15
EAX=0003 EBX=1111 ECX=2222 EDX=3333 ESP=0000 EBP=5555 ESI=6666 EDI=7777
AX=4E08 BX=C505 CX=0003 DX=202A SP=6CAA BP=5555 SI=5CF9 DI=7777
DS=C000 ES=BAD0 SS=C000 CS=F000 IP=FE15 NV UP -- PL ZR NA PE NC
CS:IP = F4 C558 C000 0244 3000 0000 01B4 AC63 0200
UNHANDLED INT 10 FUNCTION 0007 WITHIN EMULATION
F_INSTALL_CONSOLE: END
auto-booting...
do_load: dev="" dlen=0 args="" alen=0
do_load: alstr=""
do_load: path doesn't start with /
do_load: <diag-device> == <eth>
do_load: no args..use the default
do_load: <diag-file> == <diag>
try_load: dev="eth" dlen=3 args="diag" alen=4
entering main read/eval loop...
[...]
atapi_cmd: cmdlen=12
atapi_cmd: inlen=2048 len=2048
iso_walk: read: name="zImage.chrp" extent=0x44FD size=0x337272 ret=no error
iso9660: return R_END
file_system: return end (-4089)
disk-label return len=3371634 ret=end (-4089)
ata_disk_close
disk-label close:
checking exec type Fcode
fcode_is_exec: load=0x400000 loadlen=3371634
checking exec type Forth
checking exec type ELF
f_go:
checking exec type Fcode
fcode_is_exec: load=0x400000 loadlen=3371634
checking exec type Forth
checking exec type ELF
alloc_aligned: a 0xFD548E8 align 0xFD5491C size 0xFD54918 addr 0xFD54914
alloc_constrained: min 0x0, max 0xFFFFFFFF, align 0x1000, mask
0xFFFFFFFF, size 0x332000, addr 0x300000
alloc_constrained: acells 0x1 scells 0x1 t1 0xC t2 0xFD5490C u1
0xFD54910 u2 0xFD54914 u3 0xFD54918
alloc_constrained: allocator_block 0xFD54930, next 0x0 addr 0x300000
size 0xFD00000
alloc_constrained: fsblock 0x0
alloc_constrained: addr[] 0x300000
alloc_constrained: bsize[] 0xFD00000
alloc_constrained: passed min check
alloc_constrained: addr 0x300000, align 0xFFF, off 0x69696969
sum 0x0
alloc_constrained: passed align check
alloc_constrained: passed max check
alloc_constrained: passed mask check
alloc_constrained: passed full size check
alloc_constrained: passed size check
alloc_aligned: a 0xFD548E8 align 0xFD5491C size 0xFD54918 addr 0xFD54914
alloc_constrained: min 0x0, max 0xFFFFFFFF, align 0x1000, mask
0xFFFFFFFF, size 0x6883C0, addr 0x632000
alloc_constrained: acells 0x1 scells 0x1 t1 0xC t2 0xFD5490C u1
0xFD54910 u2 0xFD54914 u3 0xFD54918
alloc_constrained: allocator_block 0xFD54930, next 0x0 addr 0x632000
size 0xF9CE000
alloc_constrained: fsblock 0x0
alloc_constrained: addr[] 0x632000
alloc_constrained: bsize[] 0xF9CE000
alloc_constrained: passed min check
alloc_constrained: addr 0x632000, align 0xFFF, off 0x0
sum 0x0
alloc_constrained: passed align check
alloc_constrained: passed max check
alloc_constrained: passed mask check
alloc_constrained: passed full size check
alloc_constrained: passed size check
and here giving a try with a smaller (1.9MB) linux boot kernel
[...]
atapi_cmd: cmdlen=12
atapi_cmd: inlen=2048 len=2048
iso_walk: read: name="zImage.chrp" extent=0x3CC size=0x1D8A1A ret=no error
iso9660: return R_END
file_system: return end (-4089)
disk-label return len=1935898 ret=end (-4089)
ata_disk_close
disk-label close:
checking exec type Fcode
fcode_is_exec: load=0x400000 loadlen=1935898
checking exec type Forth
checking exec type ELF
f_go:
checking exec type Fcode
fcode_is_exec: load=0x400000 loadlen=1935898
checking exec type Forth
checking exec type ELF
alloc_aligned: a 0xFD548E8 align 0xFD5491C size 0xFD54918 addr 0xFD54914
alloc_constrained: min 0x0, max 0xFFFFFFFF, align 0x1000, mask
0xFFFFFFFF, size 0x1D3000, addr 0x300000
alloc_constrained: acells 0x1 scells 0x1 t1 0xC t2 0xFD5490C u1
0xFD54910 u2 0xFD54914 u3 0xFD54918
alloc_constrained: allocator_block 0xFD54930, next 0x0 addr 0x300000
size 0xFD00000
alloc_constrained: fsblock 0x0
alloc_constrained: addr[] 0x300000
alloc_constrained: bsize[] 0xFD00000
alloc_constrained: passed min check
alloc_constrained: addr 0x300000, align 0xFFF, off 0x69696969
sum 0x0
alloc_constrained: passed align check
alloc_constrained: passed max check
alloc_constrained: passed mask check
alloc_constrained: passed full size check
alloc_constrained: passed size check
alloc_aligned: a 0xFD548E8 align 0xFD5491C size 0xFD54918 addr 0xFD54914
alloc_constrained: min 0x0, max 0xFFFFFFFF, align 0x1000, mask
0xFFFFFFFF, size 0x3AC9A0, addr 0x4D3000
alloc_constrained: acells 0x1 scells 0x1 t1 0xC t2 0xFD5490C u1
0xFD54910 u2 0xFD54914 u3 0xFD54918
alloc_constrained: allocator_block 0xFD54930, next 0x0 addr 0x4D3000
size 0xFB2D000
alloc_constrained: fsblock 0x0
alloc_constrained: addr[] 0x4D3000
alloc_constrained: bsize[] 0xFB2D000
alloc_constrained: passed min check
alloc_constrained: addr 0x4D3000, align 0xFFF, off 0x0
sum 0x0
alloc_constrained: passed align check
alloc_constrained: passed max check
alloc_constrained: passed mask check
alloc_constrained: passed full size check
alloc_constrained: passed size check
More information about the Linuxppc-dev
mailing list