[PATCH] powerpc/85xx: Add p2040 RDB board support
Mingkai Hu
Mingkai.hu at freescale.com
Tue Jun 28 17:52:34 EST 2011
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu at freescale.com>
---
Based on http://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git
arch/powerpc/boot/dts/p2040rdb.dts | 166 +++++++
arch/powerpc/boot/dts/p2040si.dtsi | 623 ++++++++++++++++++++++++++
arch/powerpc/configs/corenet32_smp_defconfig | 1 +
arch/powerpc/platforms/85xx/Kconfig | 12 +
arch/powerpc/platforms/85xx/Makefile | 1 +
arch/powerpc/platforms/85xx/p2040_rdb.c | 88 ++++
6 files changed, 891 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p2040rdb.dts
create mode 100644 arch/powerpc/boot/dts/p2040si.dtsi
create mode 100644 arch/powerpc/platforms/85xx/p2040_rdb.c
diff --git a/arch/powerpc/boot/dts/p2040rdb.dts b/arch/powerpc/boot/dts/p2040rdb.dts
new file mode 100644
index 0000000..7d84e39
--- /dev/null
+++ b/arch/powerpc/boot/dts/p2040rdb.dts
@@ -0,0 +1,166 @@
+/*
+ * P2040RDB Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "p2040si.dtsi"
+
+/ {
+ model = "fsl,P2040RDB";
+ compatible = "fsl,P2040RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ memory {
+ device_type = "memory";
+ };
+
+ soc: soc at ffe000000 {
+ spi at 110000 {
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+ partition at u-boot {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition at kernel {
+ label = "kernel";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition at dtb {
+ label = "dtb";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition at fs {
+ label = "file system";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+ };
+
+ i2c at 118000 {
+ lm75b at 48 {
+ compatible = "nxp,lm75a";
+ reg = <0x48>;
+ };
+ eeprom at 50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+ rtc at 68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
+ i2c at 118100 {
+ eeprom at 50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+ };
+
+ usb0: usb at 210000 {
+ phy_type = "utmi";
+ };
+
+ usb1: usb at 211000 {
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+ };
+
+ localbus at ffe124000 {
+ reg = <0xf 0xfe124000 0 0x1000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000>;
+
+ flash at 0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x08000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ };
+ };
+
+ pci0: pcie at ffe200000 {
+ reg = <0xf 0xfe200000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie at 0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie at ffe201000 {
+ reg = <0xf 0xfe201000 0 0x1000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie at 0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie at ffe202000 {
+ reg = <0xf 0xfe202000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie at 0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p2040si.dtsi b/arch/powerpc/boot/dts/p2040si.dtsi
new file mode 100644
index 0000000..0babc1d
--- /dev/null
+++ b/arch/powerpc/boot/dts/p2040si.dtsi
@@ -0,0 +1,623 @@
+/*
+ * P2040 Silicon Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/ {
+ compatible = "fsl,P2040";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ dma0 = &dma0;
+ dma1 = &dma1;
+ sdhc = &sdhc;
+ msi0 = &msi0;
+ msi1 = &msi1;
+ msi2 = &msi2;
+
+ crypto = &crypto;
+ sec_jr0 = &sec_jr0;
+ sec_jr1 = &sec_jr1;
+ sec_jr2 = &sec_jr2;
+ sec_jr3 = &sec_jr3;
+ rtic_a = &rtic_a;
+ rtic_b = &rtic_b;
+ rtic_c = &rtic_c;
+ rtic_d = &rtic_d;
+ sec_mon = &sec_mon;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e500mc at 0 {
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e500mc at 1 {
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e500mc at 2 {
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e500mc at 3 {
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+
+ soc: soc at ffe000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+ ranges = <0x00000000 0xf 0xfe000000 0x1000000>;
+ reg = <0xf 0xfe000000 0 0x00001000>;
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law at 0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <32>;
+ };
+
+ memory-controller at 8000 {
+ compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller at 10000 {
+ compatible = "fsl,p2040-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf at 18000 {
+ compatible = "fsl,corenet-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu at 20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x4000>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ };
+
+ mpic: pic at 40000 {
+ clock-frequency = <0>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <4>;
+ reg = <0x40000 0x40000>;
+ compatible = "fsl,mpic", "chrp,open-pic";
+ device_type = "open-pic";
+ };
+
+ msi0: msi at 41600 {
+ compatible = "fsl,mpic-msi";
+ reg = <0x41600 0x200>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe0 0 0 0
+ 0xe1 0 0 0
+ 0xe2 0 0 0
+ 0xe3 0 0 0
+ 0xe4 0 0 0
+ 0xe5 0 0 0
+ 0xe6 0 0 0
+ 0xe7 0 0 0>;
+ };
+
+ msi1: msi at 41800 {
+ compatible = "fsl,mpic-msi";
+ reg = <0x41800 0x200>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xe8 0 0 0
+ 0xe9 0 0 0
+ 0xea 0 0 0
+ 0xeb 0 0 0
+ 0xec 0 0 0
+ 0xed 0 0 0
+ 0xee 0 0 0
+ 0xef 0 0 0>;
+ };
+
+ msi2: msi at 41a00 {
+ compatible = "fsl,mpic-msi";
+ reg = <0x41a00 0x200>;
+ msi-available-ranges = <0 0x100>;
+ interrupts = <
+ 0xf0 0 0 0
+ 0xf1 0 0 0
+ 0xf2 0 0 0
+ 0xf3 0 0 0
+ 0xf4 0 0 0
+ 0xf5 0 0 0
+ 0xf6 0 0 0
+ 0xf7 0 0 0>;
+ };
+
+ guts: global-utilities at e0000 {
+ compatible = "fsl,qoriq-device-config-1.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ #sleep-cells = <1>;
+ fsl,liodn-bits = <12>;
+ };
+
+ pins: global-utilities at e0e00 {
+ compatible = "fsl,qoriq-pin-control-1.0";
+ reg = <0xe0e00 0x200>;
+ #sleep-cells = <2>;
+ };
+
+ clockgen: global-utilities at e1000 {
+ compatible = "fsl,p2040-clockgen", "fsl,qoriq-clockgen-1.0";
+ reg = <0xe1000 0x1000>;
+ clock-frequency = <0>;
+ };
+
+ rcpm: global-utilities at e2000 {
+ compatible = "fsl,qoriq-rcpm-1.0";
+ reg = <0xe2000 0x1000>;
+ #sleep-cells = <1>;
+ };
+
+ sfp: sfp at e8000 {
+ compatible = "fsl,p2040-sfp", "fsl,qoriq-sfp-1.0";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes at ea000 {
+ compatible = "fsl,p2040-serdes";
+ reg = <0xea000 0x1000>;
+ };
+
+ dma0: dma at 100300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p2040-dma", "fsl,eloplus-dma";
+ reg = <0x100300 0x4>;
+ ranges = <0x0 0x100100 0x200>;
+ cell-index = <0>;
+ dma-channel at 0 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupts = <28 2 0 0>;
+ };
+ dma-channel at 80 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupts = <29 2 0 0>;
+ };
+ dma-channel at 100 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupts = <30 2 0 0>;
+ };
+ dma-channel at 180 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupts = <31 2 0 0>;
+ };
+ };
+
+ dma1: dma at 101300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p2040-dma", "fsl,eloplus-dma";
+ reg = <0x101300 0x4>;
+ ranges = <0x0 0x101100 0x200>;
+ cell-index = <1>;
+ dma-channel at 0 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupts = <32 2 0 0>;
+ };
+ dma-channel at 80 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupts = <33 2 0 0>;
+ };
+ dma-channel at 100 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupts = <34 2 0 0>;
+ };
+ dma-channel at 180 {
+ compatible = "fsl,p2040-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupts = <35 2 0 0>;
+ };
+ };
+
+ spi at 110000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,p2040-espi", "fsl,mpc8536-espi";
+ reg = <0x110000 0x1000>;
+ interrupts = <53 0x2 0 0>;
+ fsl,espi-num-chipselects = <4>;
+
+ };
+
+ sdhc: sdhc at 114000 {
+ compatible = "fsl,p2040-esdhc", "fsl,esdhc";
+ reg = <0x114000 0x1000>;
+ interrupts = <48 2 0 0>;
+ sdhci,auto-cmd12;
+ clock-frequency = <0>;
+ };
+
+
+ i2c at 118000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x118000 0x100>;
+ interrupts = <38 2 0 0>;
+ dfsrr;
+ };
+
+ i2c at 118100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x118100 0x100>;
+ interrupts = <38 2 0 0>;
+ dfsrr;
+ };
+
+ i2c at 119000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <2>;
+ compatible = "fsl-i2c";
+ reg = <0x119000 0x100>;
+ interrupts = <39 2 0 0>;
+ dfsrr;
+ };
+
+ i2c at 119100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <3>;
+ compatible = "fsl-i2c";
+ reg = <0x119100 0x100>;
+ interrupts = <39 2 0 0>;
+ dfsrr;
+ };
+
+ serial0: serial at 11c500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x11c500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <36 2 0 0>;
+ };
+
+ serial1: serial at 11c600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x11c600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <36 2 0 0>;
+ };
+
+ serial2: serial at 11d500 {
+ cell-index = <2>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x11d500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <37 2 0 0>;
+ };
+
+ serial3: serial at 11d600 {
+ cell-index = <3>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x11d600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <37 2 0 0>;
+ };
+
+ gpio0: gpio at 130000 {
+ compatible = "fsl,p2040-gpio", "fsl,qoriq-gpio";
+ reg = <0x130000 0x1000>;
+ interrupts = <55 2 0 0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ usb0: usb at 210000 {
+ compatible = "fsl,p2040-usb2-mph",
+ "fsl,mpc85xx-usb2-mph", "fsl-usb2-mph";
+ reg = <0x210000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <44 0x2 0 0>;
+ port0;
+ };
+
+ usb1: usb at 211000 {
+ compatible = "fsl,p2040-usb2-dr",
+ "fsl,mpc85xx-usb2-dr", "fsl-usb2-dr";
+ reg = <0x211000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <45 0x2 0 0>;
+ };
+
+ sata at 220000 {
+ compatible = "fsl,p2040-sata", "fsl,pq-sata-v2";
+ reg = <0x220000 0x1000>;
+ interrupts = <68 0x2 0 0>;
+ };
+
+ sata at 221000 {
+ compatible = "fsl,p2040-sata", "fsl,pq-sata-v2";
+ reg = <0x221000 0x1000>;
+ interrupts = <69 0x2 0 0>;
+ };
+
+ crypto: crypto at 300000 {
+ compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x300000 0x10000>;
+ ranges = <0 0x300000 0x10000>;
+ interrupts = <92 2 0 0>;
+
+ sec_jr0: jr at 1000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x1000 0x1000>;
+ interrupts = <88 2 0 0>;
+ };
+
+ sec_jr1: jr at 2000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x2000 0x1000>;
+ interrupts = <89 2 0 0>;
+ };
+
+ sec_jr2: jr at 3000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x3000 0x1000>;
+ interrupts = <90 2 0 0>;
+ };
+
+ sec_jr3: jr at 4000 {
+ compatible = "fsl,sec-v4.2-job-ring",
+ "fsl,sec-v4.0-job-ring";
+ reg = <0x4000 0x1000>;
+ interrupts = <91 2 0 0>;
+ };
+
+ rtic at 6000 {
+ compatible = "fsl,sec-v4.2-rtic",
+ "fsl,sec-v4.0-rtic";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x6000 0x100>;
+ ranges = <0x0 0x6100 0xe00>;
+
+ rtic_a: rtic-a at 0 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x00 0x20 0x100 0x80>;
+ };
+
+ rtic_b: rtic-b at 20 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x20 0x20 0x200 0x80>;
+ };
+
+ rtic_c: rtic-c at 40 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x40 0x20 0x300 0x80>;
+ };
+
+ rtic_d: rtic-d at 60 {
+ compatible = "fsl,sec-v4.2-rtic-memory",
+ "fsl,sec-v4.0-rtic-memory";
+ reg = <0x60 0x20 0x500 0x80>;
+ };
+ };
+ };
+
+ sec_mon: sec_mon at 314000 {
+ compatible = "fsl,sec-v4.2-mon", "fsl,sec-v4.0-mon";
+ reg = <0x314000 0x1000>;
+ interrupts = <93 2 0 0>;
+ };
+
+ };
+
+ localbus at ffe124000 {
+ compatible = "fsl,p2040-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <25 2 0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ };
+
+ pci0: pcie at ffe200000 {
+ compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <0x1fca055>;
+ fsl,msi = <&msi0>;
+ interrupts = <16 2 1 15>;
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 15>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+ };
+
+ pci1: pcie at ffe201000 {
+ compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ clock-frequency = <0x1fca055>;
+ fsl,msi = <&msi1>;
+ interrupts = <16 2 1 14>;
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 14>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+ };
+
+ pci2: pcie at ffe202000 {
+ compatible = "fsl,p2040-pcie", "fsl,qoriq-pcie-v2.2";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ clock-frequency = <0x1fca055>;
+ fsl,msi = <&msi2>;
+ interrupts = <16 2 1 13>;
+ pcie at 0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 1 13>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+ };
+};
diff --git a/arch/powerpc/configs/corenet32_smp_defconfig b/arch/powerpc/configs/corenet32_smp_defconfig
index 53f3949..8ea7137 100644
--- a/arch/powerpc/configs/corenet32_smp_defconfig
+++ b/arch/powerpc/configs/corenet32_smp_defconfig
@@ -23,6 +23,7 @@ CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_P2040_RDB=y
CONFIG_P3041_DS=y
CONFIG_P4080_DS=y
CONFIG_P5020_DS=y
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index 4706c71..498534c 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -171,6 +171,18 @@ config SBC8560
help
This option enables support for the Wind River SBC8560 board
+config P2040_RDB
+ bool "Freescale P2040 RDB"
+ select DEFAULT_UIMAGE
+ select PPC_E500MC
+ select PHYS_64BIT
+ select SWIOTLB
+ select MPC8xxx_GPIO
+ select HAS_RAPIDIO
+ select PPC_EPAPR_HV_PIC
+ help
+ This option enables support for the P2040 RDB board
+
config P3041_DS
bool "Freescale P3041 DS"
select DEFAULT_UIMAGE
diff --git a/arch/powerpc/platforms/85xx/Makefile b/arch/powerpc/platforms/85xx/Makefile
index 06b0c08..a971b32 100644
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_MPC85xx_RDB) += mpc85xx_rdb.o
obj-$(CONFIG_P1010_RDB) += p1010rdb.o
obj-$(CONFIG_P1022_DS) += p1022_ds.o
obj-$(CONFIG_P1023_RDS) += p1023_rds.o
+obj-$(CONFIG_P2040_RDB) += p2040_rdb.o corenet_ds.o
obj-$(CONFIG_P3041_DS) += p3041_ds.o corenet_ds.o
obj-$(CONFIG_P4080_DS) += p4080_ds.o corenet_ds.o
obj-$(CONFIG_P5020_DS) += p5020_ds.o corenet_ds.o
diff --git a/arch/powerpc/platforms/85xx/p2040_rdb.c b/arch/powerpc/platforms/85xx/p2040_rdb.c
new file mode 100644
index 0000000..32b56ac
--- /dev/null
+++ b/arch/powerpc/platforms/85xx/p2040_rdb.c
@@ -0,0 +1,88 @@
+/*
+ * P2040 RDB Setup
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/phy.h>
+
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <linux/of_platform.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include <asm/ehv_pic.h>
+
+#include "corenet_ds.h"
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init p2040_rdb_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+#ifdef CONFIG_SMP
+ extern struct smp_ops_t smp_85xx_ops;
+#endif
+
+ if (of_flat_dt_is_compatible(root, "fsl,P2040RDB"))
+ return 1;
+
+ /* Check if we're running under the Freescale hypervisor */
+ if (of_flat_dt_is_compatible(root, "fsl,P2040RDB-hv")) {
+ ppc_md.init_IRQ = ehv_pic_init;
+ ppc_md.get_irq = ehv_pic_get_irq;
+ ppc_md.restart = fsl_hv_restart;
+ ppc_md.power_off = fsl_hv_halt;
+ ppc_md.halt = fsl_hv_halt;
+#ifdef CONFIG_SMP
+ /*
+ * Disable the timebase sync operations because we can't write
+ * to the timebase registers under the hypervisor.
+ */
+ smp_85xx_ops.give_timebase = NULL;
+ smp_85xx_ops.take_timebase = NULL;
+#endif
+ return 1;
+ }
+
+ return 0;
+}
+
+define_machine(p2040_rdb) {
+ .name = "P2040 RDB",
+ .probe = p2040_rdb_probe,
+ .setup_arch = corenet_ds_setup_arch,
+ .init_IRQ = corenet_ds_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+#endif
+ .get_irq = mpic_get_coreint_irq,
+ .restart = fsl_rstcr_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+ .power_save = e500_idle,
+};
+
+machine_device_initcall(p2040_rdb, corenet_ds_publish_devices);
+
+#ifdef CONFIG_SWIOTLB
+machine_arch_initcall(p2040_rdb, swiotlb_setup_bus_notifier);
+#endif
--
1.7.5.1
More information about the Linuxppc-dev
mailing list