[PATCH] libata/sas: only set FROZEN flag if new EH is supported
Nishanth Aravamudan
nacc at us.ibm.com
Fri Jun 24 03:15:02 EST 2011
On 23.06.2011 [14:42:00 +1000], Benjamin Herrenschmidt wrote:
> On Thu, 2011-06-23 at 14:31 +1000, Benjamin Herrenschmidt wrote:
> > On Tue, 2011-06-21 at 15:30 -0500, Brian King wrote:
> > > Looks good to me. Jeff/Tejun - any issues with merging this?
> >
> > BTW. Current upstream with that patch applied on a machine here leads to
> > several oddities, I don't know at this point whether any of that is
> > actually a regression :
>
> Ooops... pressed "send" too quickly. Here's a log excerpt with some
> comments:
Hrm, I didn't see any of this on my box, which I thought was the same as
yours :)
> ipr: IBM Power RAID SCSI Device Driver version: 2.5.2 (April 27, 2011)
> ipr 0000:04:00.0: Found IOA with IRQ: 129
> ipr 0000:04:00.0: Initializing IOA.
> ipr 0000:04:00.0: Starting IOA initialization sequence.
> ipr 0000:04:00.0: Adapter firmware version: 04220029
> ipr 0000:04:00.0: IOA initialized.
> scsi0 : IBM 2B4C Storage Adapter
> scsi 0:0:4:0: Direct-Access IBM ST9300603SS BB09 PQ: 0 ANSI: 6
> scsi scan: INQUIRY result too short (5), using 36
>
> -> Are these odd INQUIRY results expected ?
>
> scsi 0:0:5:0: Direct-Access PQ: 0 ANSI: 0
> scsi 0:0:6:0: Direct-Access IBM ST9300603SS BB09 PQ: 0 ANSI: 6
> scsi 0:0:7:0: Direct-Access IBM ST9300603SS BB09 PQ: 0 ANSI: 6
> scsi scan: INQUIRY result too short (5), using 36
> scsi 0:0:18:0: Direct-Access PQ: 0 ANSI: 0
> scsi 0:2:18:0: Enclosure IBM PSBPD6E4A 3GSAS 0109 PQ: 0 ANSI: 4
> scsi: unknown device type 31
> scsi 0:255:255:255: No Device IBM 2B4C001SISIOA 0150 PQ: 0 ANSI: 0
>
> -> The above looks odd, not sure what it means
The "unknown device type"? I see it all the time on lots of different
machines.
> ipr 0000:05:00.0: Found IOA with IRQ: 130
> ipr 0000:05:00.0: Initializing IOA.
> scsi 0:254:0:0: Processor IBM 57CB001SISIOA 0150 PQ: 0 ANSI: 0
> ipr 0000:05:00.0: Starting IOA initialization sequence.
> ipr 0000:05:00.0: Adapter firmware version: 04220029
> ipr 0000:05:00.0: IOA initialized.
> scsi1 : IBM 57CB Storage Adapter
> scsi scan: INQUIRY result too short (5), using 36
> scsi 1:0:4:0: Direct-Access PQ: 0 ANSI: 0
> scsi 1:0:5:0: Direct-Access IBM ST9300603SS BB09 PQ: 0 ANSI: 6
> scsi scan: INQUIRY result too short (5), using 36
> scsi 1:0:6:0: Direct-Access PQ: 0 ANSI: 0
> scsi 1:0:7:0: Direct-Access IBM ST9300603SS BB09 PQ: 0 ANSI: 6
> scsi 1:0:18:0: Enclosure IBM PSBPD6E4A 3GSAS 0109 PQ: 0 ANSI: 4
> scsi: On host 1 channel 0 id 18 only 511 (max_scsi_report_luns) of 402653184 luns reported, try increasing max_scsi_report_luns.
> scsi: host 1 channel 0 id 18 lun 0xc0000007f01e810f has a LUN larger than currently supported.
>
> -> Now that looks horribly wrong... that LUN number looks like a kernel pointer
Yeah, that's weird.
> scsi scan: INQUIRY result too short (5), using 36
> scsi 1:2:18:0: Direct-Access PQ: 0 ANSI: 0
> ata1.00: ATAPI: IBM RMBO0040532, SA61, max UDMA/100
> ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0)
> ata1.00: revalidation failed (errno=-22)
> ata1.00: disabled
>
> -> So SATA works "better" with the patch but doesn't actually work properly :-)
>
> scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
>
> -> That error could give us more info... not sure what it means, we do have plenty of
> memory...
That message is sort of strange. It's not necessarily referring to
memory allocation failing, but the port allocation failing in the SCSI
code. And that just means an error, like the failed to IDENTIFY above,
is occurring in the allocation path. It *can* also mean memory
allocation failure, I think, just not in this case.
I don't know much about the following errors, though, sorry.
-Nish
> scsi 1:8:0:0: Enclosure IBM VSBPD6E4B 3GSAS 01 PQ: 0 ANSI: 2
> scsi: unknown device type 31
> scsi 1:255:255:255: No Device IBM 57CB001SISIOA 0150 PQ: 0 ANSI: 0
> work_for_cpu used greatest stack depth: 9520 bytes left
> st: Version 20101219, fixed bufsize 32768, s/g segs 256
> sd 0:0:4:0: [sda] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 0:0:5:0: [sdb] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 0:0:6:0: [sdc] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 0:0:7:0: [sdd] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 0:0:18:0: [sde] READ CAPACITY failed
> sd 0:0:18:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 0:0:18:0: [sde] Sense Key : Illegal Request [current]
> sd 0:0:18:0: [sde] Add. Sense: Invalid command operation code
>
> -> Any idea what's up with that guy ?
>
> sd 0:0:4:0: Attached scsi generic sg0 type 0
> sd 0:0:5:0: [sdb] Write Protect is off
> sd 0:0:5:0: Attached scsi generic sg1 type 0
> sd 0:0:18:0: [sde] Test WP failed, assume Write Enabled
> sd 0:0:6:0: Attached scsi generic sg2 type 0
> sd 0:0:18:0: [sde] Asking for cache data failed
> sd 0:0:7:0: Attached scsi generic sg3 type 0
> sd 0:0:18:0: [sde] Assuming drive cache: write through
> sd 1:2:18:0: [sdj] READ CAPACITY failed
> sd 1:2:18:0: [sdj] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 1:2:18:0: [sdj] Sense Key : Illegal Request [current]
> sd 1:2:18:0: [sdj] Add. Sense: Invalid command operation code
>
> -> And this one ?
>
> There's more below ...
>
> sd 0:0:18:0: Attached scsi generic sg4 type 0
> sd 1:0:4:0: [sdf] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> scsi 0:2:18:0: Attached scsi generic sg5 type 13
> sd 1:0:6:0: [sdh] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> scsi 0:255:255:255: Attached scsi generic sg6 type 31
> scsi 0:254:0:0: Attached scsi generic sg7 type 3
> sd 1:0:4:0: Attached scsi generic sg8 type 0
> sd 1:2:18:0: [sdj] Test WP failed, assume Write Enabled
> sd 1:0:5:0: Attached scsi generic sg9 type 0
> sd 1:0:6:0: Attached scsi generic sg10 type 0
> sd 1:0:7:0: [sdi] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 1:2:18:0: [sdj] Asking for cache data failed
> sd 1:2:18:0: [sdj] Assuming drive cache: write through
> sd 1:0:7:0: Attached scsi generic sg11 type 0
> scsi 1:0:18:0: Attached scsi generic sg12 type 13
> sd 0:0:4:0: [sda] Write Protect is off
> sd 1:2:18:0: Attached scsi generic sg13 type 0
> sd 0:0:18:0: [sde] READ CAPACITY failed
> sd 0:0:18:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 0:0:18:0: [sde] Sense Key : Illegal Request [current]
> sd 0:0:18:0: [sde] Add. Sense: Invalid command operation code
> scsi 1:8:0:0: Attached scsi generic sg14 type 13
> scsi 1:255:255:255: Attached scsi generic sg15 type 31
> e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
> e1000: Copyright (c) 1999-2006 Intel Corporation.
> e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
> e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
> sd 1:0:6:0: [sdh] Write Protect is off
> sd 0:0:5:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:18:0: [sde] Test WP failed, assume Write Enabled
> sd 0:0:7:0: [sdd] Write Protect is off
> sd 1:2:18:0: [sdj] READ CAPACITY failed
> sd 1:2:18:0: [sdj] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sd 1:2:18:0: [sdj] Sense Key : Illegal Request [current]
> sd 1:2:18:0: [sdj] Add. Sense: Invalid command operation code
> sd 0:0:18:0: [sde] Asking for cache data failed
> sd 0:0:18:0: [sde] Assuming drive cache: write through
> sd 0:0:18:0: [sde] Attached SCSI disk
> sd 1:0:5:0: [sdg] 585937500 512-byte logical blocks: (300 GB/279 GiB)
> sd 1:0:4:0: [sdf] Write Protect is off
> sd 1:2:18:0: [sdj] Test WP failed, assume Write Enabled
> sd 0:0:6:0: [sdc] Write Protect is off
> sd 1:2:18:0: [sdj] Asking for cache data failed
> sd 1:2:18:0: [sdj] Assuming drive cache: write through
> sd 1:2:18:0: [sdj] Attached SCSI disk
> sd 0:0:7:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:4:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 1:0:6:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 1:0:4:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 1:0:5:0: [sdg] Write Protect is off
> sd 1:0:7:0: [sdi] Write Protect is off
> sd 0:0:6:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 1:0:7:0: [sdi] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 1:0:5:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdb: unknown partition table
> sdd: unknown partition table
> sdh: unknown partition table
> sdi: unknown partition table
> sdf: [AIX] unknown partition table
> sdg: unknown partition table
> e1000e 0002:03:00.0: Disabling ASPM L1
> sdc: unknown partition table
> e1000e 0002:03:00.0: (unregistered net_device): Failed to initialize MSI interrupts. Falling back to legacy interrupts.
> scsi 1:254:0:0: Processor IBM 2B4C001SISIOA 0150 PQ: 0 ANSI: 0
> sda: [AIX] unknown partition table
> sd 0:0:5:0: [sdb] Attached SCSI disk
> sd 1:0:6:0: [sdh] Attached SCSI disk
> sd 1:0:7:0: [sdi] Attached SCSI disk
> sd 0:0:6:0: [sdc] Attached SCSI disk
> sd 1:0:5:0: [sdg] Attached SCSI disk
> sd 0:0:7:0: [sdd] Attached SCSI disk
> scsi 1:254:0:0: Attached scsi generic sg16 type 3
> sd 1:0:4:0: [sdf] Attached SCSI disk
> sd 0:0:4:0: [sda] Attached SCSI disk
>
> Cheers,
> Ben.
> >
> >
> > > Thanks,
> > >
> > > Brian
> > >
> > > On 06/21/2011 11:07 AM, Nishanth Aravamudan wrote:
> > > > Ping on this -- Tejun, Brian, Jeff, this is a pretty annoying 2.6.39
> > > > regression which it would be good to have fixed in 3.0.
> > > >
> > > > Thanks,
> > > > Nish
> > > >
> > > > On 16.06.2011 [08:28:36 -0700], Nishanth Aravamudan wrote:
> > > >> On 16.06.2011 [08:28:39 -0500], Brian King wrote:
> > > >>> On 06/16/2011 02:51 AM, Tejun Heo wrote:
> > > >>>> On Wed, Jun 15, 2011 at 04:34:17PM -0700, Nishanth Aravamudan wrote:
> > > >>>>>> That looks like the right thing to do. For ipr's usage of
> > > >>>>>> libata, we don't have the concept of a port frozen state, so this flag
> > > >>>>>> should really never get set. The alternate way to fix this would be to
> > > >>>>>> only set ATA_PFLAG_FROZEN in ata_port_alloc if ap->ops->error_handler
> > > >>>>>> is not NULL.
> > > >>>>>
> > > >>>>> It seemed like ipr is as you say, but I wasn't sure if it was
> > > >>>>> appropriate to make the change above in the common libata-scis code or
> > > >>>>> not. I don't want to break some other device on accident.
> > > >>>>>
> > > >>>>> Also, I tried your suggestion, but I don't think that can happen in
> > > >>>>> ata_port_alloc? ata_port_alloc is allocated ap itself, and it seems like
> > > >>>>> ap->ops typically gets set only after ata_port_alloc returns?
> > > >>>>
> > > >>>> Maybe we can test error_handler in ata_sas_port_start()?
> > > >>>
> > > >>> Good point. Since libsas is converted to the new eh now, we would need to have
> > > >>> this test.
> > > >>
> > > >> Commit 7b3a24c57d2eeda8dba9c205342b12689c4679f9 ("ahci: don't enable
> > > >> port irq before handler is registered") caused a regression for CD-ROMs
> > > >> attached to the IPR SATA bus on Power machines:
> > > >>
> > > >> ata_port_alloc: ENTER
> > > >> ata_port_probe: ata1: bus probe begin
> > > >> ata1.00: ata_dev_read_id: ENTER
> > > >> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
> > > >> ata1.00: ata_dev_read_id: ENTER
> > > >> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
> > > >> ata1.00: limiting speed to UDMA7:PIO5
> > > >> ata1.00: ata_dev_read_id: ENTER
> > > >> ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
> > > >> ata1.00: disabled
> > > >> ata_port_probe: ata1: bus probe end
> > > >> scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
> > > >>
> > > >> The FROZEN flag added in that commit is only cleared by the new EH code,
> > > >> which is not used by ipr. Clear this flag in the SAS code if we don't
> > > >> support new EH.
> > > >>
> > > >> Reported-by: Benjamin Herrenschmidt <benh at kernel.crashing.org>
> > > >> Signed-off-by: Nishanth Aravamudan <nacc at us.ibm.com>
> > > >>
> > > >> diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c
> > > >> index d51f979..ebe1685 100644
> > > >> --- a/drivers/ata/libata-scsi.c
> > > >> +++ b/drivers/ata/libata-scsi.c
> > > >> @@ -3797,6 +3797,12 @@ EXPORT_SYMBOL_GPL(ata_sas_port_alloc);
> > > >> */
> > > >> int ata_sas_port_start(struct ata_port *ap)
> > > >> {
> > > >> + /*
> > > >> + * the port is marked as frozen at allocation time, but if we don't
> > > >> + * have new eh, we won't thaw it
> > > >> + */
> > > >> + if (!ap->ops->error_handler)
> > > >> + ap->pflags &= ~ATA_PFLAG_FROZEN;
> > > >> return 0;
> > > >> }
> > > >> EXPORT_SYMBOL_GPL(ata_sas_port_start);
> > > >>
> > > >>
> > > >> --
> > > >> Nishanth Aravamudan <nacc at us.ibm.com>
> > > >> IBM Linux Technology Center
> > > >
> > >
> > >
> >
>
>
--
Nishanth Aravamudan <nacc at us.ibm.com>
IBM Linux Technology Center
More information about the Linuxppc-dev
mailing list