[PATCH v2 2/4] powerpc, mpc52xx: add a4m072 board support

Heiko Schocher hs at denx.de
Wed Jun 22 20:39:10 EST 2011


Signed-off-by: Heiko Schocher <hs at denx.de>
cc: Grant Likely <grant.likely at secretlab.ca>
cc: devicetree-discuss at ozlabs.org
cc: Wolfgang Denk <wd at denx.de>
cc: Wolfram Sang <w.sang at pengutronix.de>
---
For this patchseries following patch is needed:

http://patchwork.ozlabs.org/patch/91919/

Grant? Do you have some comments on that patch?

changes for v2:
  add comment from Wolfram Sang:
  use mpc5200.dtsi

 arch/powerpc/boot/dts/a4m072.dts             |  172 ++++++++++++++++++++++++++
 arch/powerpc/platforms/52xx/mpc5200_simple.c |    1 +
 2 files changed, 173 insertions(+), 0 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/a4m072.dts

diff --git a/arch/powerpc/boot/dts/a4m072.dts b/arch/powerpc/boot/dts/a4m072.dts
new file mode 100644
index 0000000..adb6746
--- /dev/null
+++ b/arch/powerpc/boot/dts/a4m072.dts
@@ -0,0 +1,172 @@
+/*
+ * a4m072 board Device Tree Source
+ *
+ * Copyright (C) 2011 DENX Software Engineering GmbH
+ * Heiko Schocher <hs at denx.de>
+ *
+ * Copyright (C) 2007 Semihalf
+ * Marian Balakowicz <m8 at semihalf.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/include/ "mpc5200b.dtsi"
+
+/ {
+	model = "anonymous,a4m072";
+	compatible = "anonymous,a4m072";
+
+	soc5200 at f0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc5200b-immr";
+		ranges = <0 0xf0000000 0x0000c000>;
+		reg = <0xf0000000 0x00000100>;
+		bus-frequency = <0>; /* From boot loader */
+		system-frequency = <0>; /* From boot loader */
+
+		cdm at 200 {
+			fsl,ext_48mhz_en = <0x0>;
+			fsl,fd_enable = <0x01>;
+			fsl,fd_counters = <0xbbbb>;
+		};
+
+		timer at 600 {
+			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+			reg = <0x600 0x80>;
+			interrupts = <1 9 0>;
+			fsl,has-wdt;
+		};
+
+		gpt3: timer at 630 { /* General Purpose Timer in GPIO mode */
+			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpt4: timer at 640 { /* General Purpose Timer in GPIO mode */
+			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpt5: timer at 650 { /* General Purpose Timer in GPIO mode */
+			compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		spi at f00 {
+			status = "disabled";
+		};
+
+		psc at 2000 {
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+			reg = <0x2000 0x100>;
+			interrupts = <2 1 0>;
+		};
+
+		psc at 2200 {
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+			reg = <0x2200 0x100>;
+			interrupts = <2 2 0>;
+		};
+
+		psc at 2400 {
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+			reg = <0x2400 0x100>;
+			interrupts = <2 3 0>;
+		};
+
+		psc at 2600 {
+			status = "disabled";
+		};
+
+		psc at 2800 {
+			status = "disabled";
+		};
+
+		psc at 2c00 {
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+			reg = <0x2c00 0x100>;
+			interrupts = <2 4 0>;
+		};
+
+		ethernet at 3000 {
+			phy-handle = <&phy0>;
+		};
+
+		mdio at 3000 {
+			phy0: ethernet-phy at 1f {
+				reg = <0x1f>;
+				interrupts = <1 2 0>; /* IRQ 2 active low */
+			};
+		};
+
+		i2c at 3d00 {
+			status = "disabled";
+		};
+
+		i2c at 3d40 {
+			 hwmon at 2e {
+				compatible = "nsc,lm87";
+				reg = <0x2e>;
+			};
+			 rtc at 51 {
+				compatible = "nxp,rtc8564";
+				reg = <0x51>;
+			};
+		};
+	};
+
+	localbus {
+		compatible = "fsl,mpc5200b-lpb","simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0xfe000000 0x02000000
+			  1 0 0x62000000 0x00400000
+			  2 0 0x64000000 0x00200000
+			  3 0 0x66000000 0x01000000
+			  6 0 0x68000000 0x01000000
+			  7 0 0x6a000000 0x00000004
+			 >;
+
+		flash at 0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x02000000>;
+			bank-width = <2>;
+			#size-cells = <1>;
+			#address-cells = <1>;
+		};
+		sram0 at 1,0 {
+			compatible = "mtd-ram";
+			reg = <1 0x00000 0x00400000>;
+			bank-width = <2>;
+		};
+	};
+
+	pci at f0000d00 {
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		compatible = "fsl,mpc5200-pci";
+		reg = <0xf0000d00 0x100>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+				 /* IDSEL 0x16 */
+				 0xc000 0 0 1 &mpc5200_pic 1 3 3
+				 0xc000 0 0 2 &mpc5200_pic 1 3 3
+				 0xc000 0 0 3 &mpc5200_pic 1 3 3
+				 0xc000 0 0 4 &mpc5200_pic 1 3 3>;
+		clock-frequency = <0>; /* From boot loader */
+		interrupts = <2 8 0 2 9 0 2 10 0>;
+		bus-range = <0 0>;
+		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
+			  0x02000000 0 0x90000000 0x90000000 0 0x10000000
+			  0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
+	};
+};
diff --git a/arch/powerpc/platforms/52xx/mpc5200_simple.c b/arch/powerpc/platforms/52xx/mpc5200_simple.c
index e36d6e2..192b4ff 100644
--- a/arch/powerpc/platforms/52xx/mpc5200_simple.c
+++ b/arch/powerpc/platforms/52xx/mpc5200_simple.c
@@ -50,6 +50,7 @@ static void __init mpc5200_simple_setup_arch(void)
 
 /* list of the supported boards */
 static const char *board[] __initdata = {
+	"anonymous,a4m072",
 	"intercontrol,digsy-mtc",
 	"manroland,mucmc52",
 	"manroland,uc101",
-- 
1.7.5.4



More information about the Linuxppc-dev mailing list