[PATCH 2/2] misc: add CARMA DATA-FPGA Programmer support
Ira W. Snyder
iws at ovro.caltech.edu
Tue Feb 8 10:23:41 EST 2011
This adds support for programming the data processing FPGAs on the OVRO
CARMA board. These FPGAs have a special programming sequence that
requires that we program the Freescale DMA engine, which is only
available inside the kernel.
Signed-off-by: Ira W. Snyder <iws at ovro.caltech.edu>
---
drivers/misc/carma/Kconfig | 9 +
drivers/misc/carma/Makefile | 1 +
drivers/misc/carma/carma-fpga-program.c | 1084 +++++++++++++++++++++++++++++++
3 files changed, 1094 insertions(+), 0 deletions(-)
create mode 100644 drivers/misc/carma/carma-fpga-program.c
diff --git a/drivers/misc/carma/Kconfig b/drivers/misc/carma/Kconfig
index 4be183f..e57a9d3 100644
--- a/drivers/misc/carma/Kconfig
+++ b/drivers/misc/carma/Kconfig
@@ -7,3 +7,12 @@ config CARMA_FPGA
Say Y here to include support for communicating with the data
processing FPGAs on the OVRO CARMA board.
+config CARMA_FPGA_PROGRAM
+ tristate "CARMA DATA-FPGA Programmer"
+ depends on FSL_SOC && PPC_83xx && MEDIA_SUPPORT && HAS_DMA && FSL_DMA
+ select VIDEOBUF_DMA_SG
+ default n
+ help
+ Say Y here to include support for programming the data processing
+ FPGAs on the OVRO CARMA board.
+
diff --git a/drivers/misc/carma/Makefile b/drivers/misc/carma/Makefile
index 0b69fa7..ff36ac2 100644
--- a/drivers/misc/carma/Makefile
+++ b/drivers/misc/carma/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_CARMA_FPGA) += carma-fpga.o
+obj-$(CONFIG_CARMA_FPGA_PROGRAM) += carma-fpga-program.o
diff --git a/drivers/misc/carma/carma-fpga-program.c b/drivers/misc/carma/carma-fpga-program.c
new file mode 100644
index 0000000..ef16cb3
--- /dev/null
+++ b/drivers/misc/carma/carma-fpga-program.c
@@ -0,0 +1,1084 @@
+/*
+ * CARMA Board DATA-FPGA Programmer
+ *
+ * Copyright (c) 2009-2010 Ira W. Snyder <iws at ovro.caltech.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/of_platform.h>
+#include <linux/completion.h>
+#include <linux/miscdevice.h>
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/highmem.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/slab.h>
+#include <linux/fs.h>
+#include <linux/io.h>
+
+#include <media/videobuf-dma-sg.h>
+
+/* MPC8349EMDS specific get_immrbase() */
+#include <sysdev/fsl_soc.h>
+
+static const char drv_name[] = "carma-fpga-program";
+
+/*
+ * Maximum firmware size
+ *
+ * 12849552 bytes for a CARMA Digitizer Board
+ * 18662880 bytes for a CARMA Correlator Board
+ */
+#define FW_SIZE_EP2S90 12849552
+#define FW_SIZE_EP2S130 18662880
+
+struct fpga_dev {
+ struct miscdevice miscdev;
+
+ /* Device Registers */
+ struct device *dev;
+ void __iomem *regs;
+ void __iomem *immr;
+
+ /* Freescale DMA Device */
+ struct dma_chan *chan;
+
+ /* Interrupts */
+ int irq, status;
+ struct completion completion;
+
+ /* FPGA Bitfile */
+ struct mutex lock;
+
+ struct videobuf_dmabuf vb;
+ bool vb_allocated;
+
+ /* max size and written bytes */
+ size_t fw_size;
+ size_t bytes;
+};
+
+/*
+ * FPGA Bitfile Helpers
+ */
+
+/**
+ * fpga_drop_firmware_data() - drop the bitfile image from memory
+ * @priv: the driver's private data structure
+ *
+ * LOCKING: must hold priv->lock
+ */
+static void fpga_drop_firmware_data(struct fpga_dev *priv)
+{
+ videobuf_dma_free(&priv->vb);
+ priv->vb_allocated = false;
+ priv->bytes = 0;
+}
+
+/*
+ * LED Trigger (could be a seperate module)
+ */
+
+/*
+ * NOTE: this whole thing does have the problem that whenever the led's are
+ * NOTE: first set to use the fpga trigger, they could be in the wrong state
+ */
+
+DEFINE_LED_TRIGGER(ledtrig_fpga);
+
+static void ledtrig_fpga_programmed(bool enabled)
+{
+ if (enabled)
+ led_trigger_event(ledtrig_fpga, LED_FULL);
+ else
+ led_trigger_event(ledtrig_fpga, LED_OFF);
+}
+
+/*
+ * FPGA Register Helpers
+ */
+
+/* Register Definitions */
+#define FPGA_CONFIG_CONTROL 0x40
+#define FPGA_CONFIG_STATUS 0x44
+#define FPGA_CONFIG_FIFO_SIZE 0x48
+#define FPGA_CONFIG_FIFO_USED 0x4C
+#define FPGA_CONFIG_TOTAL_BYTE_COUNT 0x50
+#define FPGA_CONFIG_CUR_BYTE_COUNT 0x54
+
+#define FPGA_FIFO_ADDRESS 0x3000
+
+static int fpga_fifo_size(void __iomem *regs)
+{
+ return ioread32be(regs + FPGA_CONFIG_FIFO_SIZE);
+}
+
+static int fpga_config_error(void __iomem *regs)
+{
+ return ioread32be(regs + FPGA_CONFIG_STATUS) & 0xFFFE;
+}
+
+static int fpga_fifo_empty(void __iomem *regs)
+{
+ return ioread32be(regs + FPGA_CONFIG_FIFO_USED) == 0;
+}
+
+static void fpga_fifo_write(void __iomem *regs, u32 val)
+{
+ iowrite32be(val, regs + FPGA_FIFO_ADDRESS);
+}
+
+static void fpga_set_byte_count(void __iomem *regs, u32 count)
+{
+ iowrite32be(count, regs + FPGA_CONFIG_TOTAL_BYTE_COUNT);
+}
+
+static void fpga_programmer_enable(struct fpga_dev *priv, bool dma)
+{
+ if (dma)
+ iowrite32be(0x5, priv->regs + FPGA_CONFIG_CONTROL);
+ else
+ iowrite32be(0x1, priv->regs + FPGA_CONFIG_CONTROL);
+}
+
+static void fpga_programmer_disable(struct fpga_dev *priv)
+{
+ iowrite32be(0x0, priv->regs + FPGA_CONFIG_CONTROL);
+}
+
+static void fpga_dump_registers(struct fpga_dev *priv)
+{
+ /* good status: do nothing */
+ if (priv->status == 0)
+ return;
+
+ /* Dump all status registers */
+ dev_err(priv->dev, "Configuration failed, dumping status registers\n");
+ dev_err(priv->dev, "Control: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_CONTROL));
+ dev_err(priv->dev, "Status: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_STATUS));
+ dev_err(priv->dev, "FIFO Size: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_FIFO_SIZE));
+ dev_err(priv->dev, "FIFO Used: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_FIFO_USED));
+ dev_err(priv->dev, "FIFO Total: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_TOTAL_BYTE_COUNT));
+ dev_err(priv->dev, "FIFO Curr: 0x%.8x\n", ioread32be(priv->regs + FPGA_CONFIG_CUR_BYTE_COUNT));
+}
+
+/*
+ * FPGA Power Supply Code
+ */
+
+#define CTL_PWR_CONTROL 0x2006
+#define CTL_PWR_STATUS 0x200A
+#define CTL_PWR_FAIL 0x200B
+
+/*
+ * Determine if the FPGA power is good for all supplies
+ */
+static bool fpga_power_good(struct fpga_dev *priv)
+{
+ u8 val;
+
+ val = ioread8(priv->regs + CTL_PWR_STATUS);
+ if (val & 0x10)
+ return false;
+
+ return val == 0x0F;
+}
+
+/*
+ * Disable the FPGA power supplies
+ */
+static void fpga_disable_power_supplies(struct fpga_dev *priv)
+{
+ unsigned long start;
+ u8 val;
+
+ iowrite8(0x00, priv->regs + CTL_PWR_CONTROL);
+
+ /*
+ * Wait 500ms for the power rails to discharge
+ *
+ * Without this delay, the CTL-CPLD state machine can get into a
+ * state where it is waiting for the power-goods to assert, but they
+ * never do. This only happens when enabling and disabling the
+ * power sequencer very rapidly.
+ *
+ * The loop below will also wait for the power goods to de-assert,
+ * but testing has shown that they are always disabled by the time
+ * the sleep completes. However, omitting the sleep and only waiting
+ * for the power-goods to de-assert was not sufficient to ensure
+ * that the power sequencer would not wedge itself.
+ */
+ msleep(500);
+
+ start = jiffies;
+ while (time_before(jiffies, start + HZ)) {
+ val = ioread8(priv->regs + CTL_PWR_STATUS);
+ if (!(val & 0x0f))
+ break;
+
+ msleep(10);
+ }
+
+ val = ioread8(priv->regs + CTL_PWR_STATUS);
+ if (val & 0x0f) {
+ dev_err(priv->dev, "power disable failed: "
+ "power goods: status 0x%.2x\n", val);
+ }
+
+ if (val & 0x10) {
+ dev_err(priv->dev, "power disable failed: "
+ "alarm bit set: status 0x%.2x\n", val);
+ }
+}
+
+/**
+ * fpga_enable_power_supplies() - enable the DATA-FPGA power supplies
+ * @priv: the driver's private data structure
+ *
+ * Enable the DATA-FPGA power supplies, waiting up to 1 second for
+ * them to enable successfully.
+ *
+ * Returns 0 on success, -ERRNO otherwise
+ */
+static int fpga_enable_power_supplies(struct fpga_dev *priv)
+{
+ unsigned long start = jiffies;
+
+ if (fpga_power_good(priv)) {
+ dev_dbg(priv->dev, "power was already good\n");
+ return 0;
+ }
+
+ iowrite8(0x01, priv->regs + CTL_PWR_CONTROL);
+ while (time_before(jiffies, start + HZ)) {
+ if (fpga_power_good(priv))
+ return 0;
+
+ msleep(10);
+ }
+
+ return fpga_power_good(priv) ? 0 : -EBUSY;
+}
+
+/*
+ * Determine if the FPGA power supplies are all enabled
+ */
+static bool fpga_power_enabled(struct fpga_dev *priv)
+{
+ u8 val;
+
+ val = ioread8(priv->regs + CTL_PWR_CONTROL);
+ if (val & 0x01)
+ return true;
+
+ return false;
+}
+
+/*
+ * Determine if the FPGA's are programmed and running correctly
+ */
+static bool fpga_running(struct fpga_dev *priv)
+{
+ if (!fpga_power_good(priv))
+ return false;
+
+ /* Check the config done bit */
+ return ioread32be(priv->regs + FPGA_CONFIG_STATUS) & (1 << 18);
+}
+
+/*
+ * FPGA Programming Code
+ */
+
+/**
+ * fpga_program_block() - put a block of data into the programmer's FIFO
+ * @priv: the driver's private data structure
+ * @buf: the data to program
+ * @count: the length of data to program (must be a multiple of 4 bytes)
+ *
+ * Returns 0 on success, -ERRNO otherwise
+ */
+static int fpga_program_block(struct fpga_dev *priv, void *buf, size_t count)
+{
+ u32 *data = buf;
+ int size = fpga_fifo_size(priv->regs);
+ int i, len;
+ unsigned long timeout;
+
+ /* FIXME: BUG_ON instead */
+ WARN_ON_ONCE(count % 4 != 0);
+
+ while (count > 0) {
+
+ /* Get the size of the block to write (maximum is FIFO_SIZE) */
+ len = min_t(size_t, count, size);
+ timeout = jiffies + HZ / 4;
+
+ /* Write the block */
+ for (i = 0; i < len / 4; i++)
+ fpga_fifo_write(priv->regs, data[i]);
+
+ /* Update the amounts left */
+ count -= len;
+ data += len / 4;
+
+ /* Wait for the fifo to empty */
+ while (true) {
+
+ if (fpga_fifo_empty(priv->regs)) {
+ break;
+ } else {
+ dev_dbg(priv->dev, "Fifo not empty\n");
+ cpu_relax();
+ }
+
+ if (fpga_config_error(priv->regs)) {
+ dev_err(priv->dev, "Error detected\n");
+ return -EIO;
+ }
+
+ if (time_after(jiffies, timeout)) {
+ dev_err(priv->dev, "Fifo drain timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ msleep(10);
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * fpga_program_cpu() - program the DATA-FPGA's using the CPU
+ * @priv: the driver's private data structure
+ *
+ * This is useful when the DMA programming method fails. It is possible to
+ * wedge the Freescale DMA controller such that the DMA programming method
+ * always fails. This method has always succeeded.
+ *
+ * Returns 0 on success, -ERRNO otherwise
+ */
+static noinline int fpga_program_cpu(struct fpga_dev *priv)
+{
+ int ret;
+
+ /* Disable the programmer */
+ fpga_programmer_disable(priv);
+
+ /* Set the total byte count */
+ fpga_set_byte_count(priv->regs, priv->bytes);
+ dev_dbg(priv->dev, "total byte count %u bytes\n", priv->bytes);
+
+ /* Enable the controller for programming */
+ fpga_programmer_enable(priv, false);
+ dev_dbg(priv->dev, "enabled the controller\n");
+
+ /* Write each chunk of the FPGA bitfile to FPGA programmer */
+ ret = fpga_program_block(priv, priv->vb.vaddr, priv->bytes);
+ if (ret)
+ goto out_disable_controller;
+
+ /* Wait for the interrupt handler to notify us that programming finished */
+ ret = wait_for_completion_timeout(&priv->completion, 2 * HZ);
+ if (!ret) {
+ dev_err(priv->dev, "Timed out waiting for completion\n");
+ ret = -ETIMEDOUT;
+ goto out_disable_controller;
+ }
+
+ /* Retrieve the status from the interrupt handler */
+ ret = priv->status;
+
+out_disable_controller:
+ fpga_programmer_disable(priv);
+ return ret;
+}
+
+/**
+ * fpga_program_dma() - program the DATA-FPGA's using the DMA engine
+ * @priv: the driver's private data structure
+ *
+ * Program the DATA-FPGA's using the Freescale DMA engine. This requires that
+ * the engine is programmed such that the hardware DMA request lines can
+ * control the entire DMA transaction. The system controller FPGA then
+ * completely offloads the programming from the CPU.
+ *
+ * Returns 0 on success, -ERRNO otherwise
+ */
+static noinline int fpga_program_dma(struct fpga_dev *priv)
+{
+ struct videobuf_dmabuf *vb = &priv->vb;
+ struct dma_chan *chan = priv->chan;
+ struct dma_async_tx_descriptor *tx;
+ size_t num_pages, len, avail = 0;
+ struct dma_slave_config config;
+ struct scatterlist *sg;
+ struct sg_table table;
+ dma_cookie_t cookie;
+ int ret, i;
+
+ /* Disable the programmer */
+ fpga_programmer_disable(priv);
+
+ /* Allocate a scatterlist for the DMA destination */
+ num_pages = DIV_ROUND_UP(priv->bytes, 0x1000);
+ ret = sg_alloc_table(&table, num_pages, GFP_KERNEL);
+ if (ret) {
+ dev_err(priv->dev, "Unable to allocate dst scatterlist\n");
+ ret = -ENOMEM;
+ goto out_return;
+ }
+
+ /*
+ * This is an ugly hack
+ *
+ * We fill in a scatterlist as if it were mapped for DMA. This is
+ * necessary because there exists no better structure for this
+ * inside the kernel code.
+ *
+ * As an added bonus, we can use the DMAEngine API for all of this,
+ * rather than inventing another extremely similar API.
+ */
+ avail = priv->bytes;
+ for_each_sg(table.sgl, sg, num_pages, i) {
+ len = min_t(size_t, avail, 0x1000);
+ sg_dma_address(sg) = 0xf0003000;
+ sg_dma_len(sg) = len;
+
+ avail -= len;
+ }
+
+ /* Map the buffer for DMA */
+ ret = videobuf_dma_map(priv->dev, &priv->vb);
+ if (ret) {
+ dev_err(priv->dev, "Unable to map buffer for DMA\n");
+ goto out_free_table;
+ }
+
+ /*
+ * Configure the DMA channel to transfer FIFO_SIZE / 2 bytes per
+ * transaction, and then put it under external control
+ */
+ memset(&config, 0, sizeof(config));
+ config.direction = DMA_TO_DEVICE;
+ config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ config.dst_maxburst = fpga_fifo_size(priv->regs) / 2 / 4;
+ ret = chan->device->device_control(chan, DMA_SLAVE_CONFIG,
+ (unsigned long)&config);
+ if (ret) {
+ dev_err(priv->dev, "DMA slave configuration failed\n");
+ goto out_dma_unmap;
+ }
+
+ ret = chan->device->device_control(chan, FSLDMA_EXTERNAL_START, 1);
+ if (ret) {
+ dev_err(priv->dev, "DMA external control setup failed\n");
+ goto out_dma_unmap;
+ }
+
+ /* setup and submit the DMA transaction */
+ tx = chan->device->device_prep_dma_sg(chan,
+ table.sgl, num_pages,
+ vb->sglist, vb->sglen, 0);
+ if (!tx) {
+ dev_err(priv->dev, "Unable to prep DMA transaction\n");
+ ret = -ENOMEM;
+ goto out_dma_unmap;
+ }
+
+ cookie = tx->tx_submit(tx);
+ if (dma_submit_error(cookie)) {
+ dev_err(priv->dev, "Unable to submit DMA transaction\n");
+ ret = -ENOMEM;
+ goto out_dma_unmap;
+ }
+
+ dma_async_memcpy_issue_pending(chan);
+
+ /* Set the total byte count */
+ fpga_set_byte_count(priv->regs, priv->bytes);
+ dev_dbg(priv->dev, "total byte count %u bytes\n", priv->bytes);
+
+ /* Enable the controller for DMA programming */
+ fpga_programmer_enable(priv, true);
+ dev_dbg(priv->dev, "enabled the controller\n");
+
+ /* Wait for the interrupt handler to notify us that programming finished */
+ ret = wait_for_completion_timeout(&priv->completion, 2 * HZ);
+ if (!ret) {
+ dev_err(priv->dev, "Timed out waiting for completion\n");
+ ret = -ETIMEDOUT;
+ goto out_disable_controller;
+ }
+
+ /* Retrieve the status from the interrupt handler */
+ ret = priv->status;
+
+out_disable_controller:
+ fpga_programmer_disable(priv);
+out_dma_unmap:
+ videobuf_dma_unmap(priv->dev, vb);
+out_free_table:
+ sg_free_table(&table);
+out_return:
+ return ret;
+}
+
+/*
+ * Interrupt Handling
+ */
+
+static irqreturn_t fpga_interrupt(int irq, void *dev_id)
+{
+ struct fpga_dev *priv = dev_id;
+
+ /* Save the status */
+ priv->status = fpga_config_error(priv->regs) ? -EIO : 0;
+ dev_dbg(priv->dev, "INTERRUPT status %d\n", priv->status);
+ fpga_dump_registers(priv);
+
+ /* Disabling the programmer clears the interrupt */
+ fpga_programmer_disable(priv);
+
+ /* Notify any waiters */
+ complete(&priv->completion);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * SYSFS Helpers
+ */
+
+/**
+ * fpga_do_stop() - deconfigure (reset) the DATA-FPGA's
+ * @priv: the driver's private data structure
+ *
+ * LOCKING: must hold priv->lock
+ */
+static int fpga_do_stop(struct fpga_dev *priv)
+{
+ /* Set the led to unprogrammed */
+ ledtrig_fpga_programmed(false);
+
+ /* Pulse the config line to reset the FPGA's */
+ iowrite32be(0x3, priv->regs + FPGA_CONFIG_CONTROL);
+ iowrite32be(0x0, priv->regs + FPGA_CONFIG_CONTROL);
+
+ return 0;
+}
+
+static noinline int fpga_do_program(struct fpga_dev *priv)
+{
+ int ret;
+
+ if (priv->bytes != priv->fw_size) {
+ dev_err(priv->dev, "Incorrect bitfile size: got %zu bytes, "
+ "should be %zu bytes\n",
+ priv->bytes, priv->fw_size);
+ return -EINVAL;
+ }
+
+ if (!fpga_power_enabled(priv)) {
+ dev_err(priv->dev, "Power not enabled\n");
+ return -EINVAL;
+ }
+
+ if (!fpga_power_good(priv)) {
+ dev_err(priv->dev, "Power not good\n");
+ return -EINVAL;
+ }
+
+ /* Set the LED to unprogrammed */
+ ledtrig_fpga_programmed(false);
+
+ /* Try to program the FPGA's using DMA */
+ ret = fpga_program_dma(priv);
+
+ /* If DMA failed or doesn't exist, try with CPU */
+ if (ret) {
+ dev_warn(priv->dev, "Falling back to CPU programming\n");
+ ret = fpga_program_cpu(priv);
+ }
+
+ if (ret) {
+ dev_err(priv->dev, "Unable to program FPGA's\n");
+ return ret;
+ }
+
+ /* Drop the firmware bitfile from memory */
+ fpga_drop_firmware_data(priv);
+
+ dev_dbg(priv->dev, "FPGA programming successful\n");
+ ledtrig_fpga_programmed(true);
+
+ return 0;
+}
+
+/*
+ * File Operations
+ */
+
+static int fpga_open(struct inode *inode, struct file *filp)
+{
+ /*
+ * The miscdevice layer puts our struct miscdevice into the
+ * filp->private_data field. We use this to find our private
+ * data and then overwrite it with our own private structure.
+ */
+ struct fpga_dev *priv = container_of(filp->private_data,
+ struct fpga_dev, miscdev);
+ unsigned int nr_pages;
+ int ret;
+
+ /* We only allow one process at a time */
+ if (mutex_lock_interruptible(&priv->lock))
+ return -ERESTARTSYS;
+
+ filp->private_data = priv;
+
+ /* Truncation: drop any existing data */
+ if (filp->f_flags & O_TRUNC)
+ priv->bytes = 0;
+
+ /* Check if we have already allocated a buffer */
+ if (priv->vb_allocated)
+ return 0;
+
+ /* Allocate a buffer to hold enough data for the bitfile */
+ nr_pages = DIV_ROUND_UP(priv->fw_size, PAGE_SIZE);
+ ret = videobuf_dma_init_kernel(&priv->vb, DMA_TO_DEVICE, nr_pages);
+ if (ret) {
+ dev_err(priv->dev, "unable to allocate data buffer\n");
+ mutex_unlock(&priv->lock);
+ return ret;
+ }
+
+ priv->vb_allocated = true;
+ return 0;
+}
+
+static int fpga_release(struct inode *inode, struct file *filp)
+{
+ struct fpga_dev *priv = filp->private_data;
+
+ mutex_unlock(&priv->lock);
+ return 0;
+}
+
+static ssize_t fpga_write(struct file *filp, const char __user *buf,
+ size_t count, loff_t *f_pos)
+{
+ struct fpga_dev *priv = filp->private_data;
+
+ /* FPGA bitfiles have an exact size: disallow anything else */
+ if (priv->bytes >= priv->fw_size)
+ return -ENOSPC;
+
+ count = min_t(size_t, priv->fw_size - priv->bytes, count);
+ if (copy_from_user(priv->vb.vaddr + priv->bytes, buf, count))
+ return -EFAULT;
+
+ priv->bytes += count;
+ return count;
+}
+
+static ssize_t fpga_read(struct file *filp, char __user *buf, size_t count,
+ loff_t *f_pos)
+{
+ struct fpga_dev *priv = filp->private_data;
+
+ count = min_t(size_t, priv->bytes - *f_pos, count);
+ if (copy_to_user(buf, priv->vb.vaddr + *f_pos, count))
+ return -EFAULT;
+
+ *f_pos += count;
+ return count;
+}
+
+static loff_t fpga_llseek(struct file *filp, loff_t offset, int origin)
+{
+ struct fpga_dev *priv = filp->private_data;
+ loff_t newpos;
+
+ /* only read-only opens are allowed to seek */
+ if ((filp->f_flags & O_ACCMODE) != O_RDONLY)
+ return -EINVAL;
+
+ switch (origin) {
+ case SEEK_SET: /* seek relative to the beginning of the file */
+ newpos = offset;
+ break;
+ case SEEK_CUR: /* seek relative to current position in the file */
+ newpos = filp->f_pos + offset;
+ break;
+ case SEEK_END: /* seek relative to the end of the file */
+ newpos = priv->fw_size - offset;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* check for sanity */
+ if (newpos > priv->fw_size)
+ return -EINVAL;
+
+ filp->f_pos = newpos;
+ return newpos;
+}
+
+static const struct file_operations fpga_fops = {
+ .open = fpga_open,
+ .release = fpga_release,
+ .write = fpga_write,
+ .read = fpga_read,
+ .llseek = fpga_llseek,
+};
+
+/*
+ * Device Attributes
+ */
+
+static ssize_t pfail_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ u8 val;
+
+ val = ioread8(priv->regs + CTL_PWR_FAIL);
+ return snprintf(buf, PAGE_SIZE, "0x%.2x\n", val);
+}
+
+static ssize_t pgood_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ return snprintf(buf, PAGE_SIZE, "%d\n", fpga_power_good(priv));
+}
+
+static ssize_t penable_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ return snprintf(buf, PAGE_SIZE, "%d\n", fpga_power_enabled(priv));
+}
+
+static ssize_t penable_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ if (strict_strtoul(buf, 0, &val))
+ return -EINVAL;
+
+ if (val) {
+ ret = fpga_enable_power_supplies(priv);
+ if (ret)
+ return ret;
+ } else {
+ fpga_do_stop(priv);
+ fpga_disable_power_supplies(priv);
+ }
+
+ return count;
+}
+
+static ssize_t program_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ return snprintf(buf, PAGE_SIZE, "%d\n", fpga_running(priv));
+}
+
+static ssize_t program_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct fpga_dev *priv = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ if (strict_strtoul(buf, 0, &val))
+ return -EINVAL;
+
+ /* We can't have an image writer and be programming simultaneously */
+ if (mutex_lock_interruptible(&priv->lock))
+ return -ERESTARTSYS;
+
+ /* Program or Reset the FPGA's */
+ ret = val ? fpga_do_program(priv) : fpga_do_stop(priv);
+ if (ret)
+ goto out_unlock;
+
+ /* Success */
+ ret = count;
+
+out_unlock:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static DEVICE_ATTR(power_fail, S_IRUGO, pfail_show, NULL);
+static DEVICE_ATTR(power_good, S_IRUGO, pgood_show, NULL);
+static DEVICE_ATTR(power_enable, S_IRUGO | S_IWUGO, penable_show, penable_store);
+static DEVICE_ATTR(program, S_IRUGO | S_IWUGO, program_show, program_store);
+
+static struct attribute *fpga_attributes[] = {
+ &dev_attr_power_fail.attr,
+ &dev_attr_power_good.attr,
+ &dev_attr_power_enable.attr,
+ &dev_attr_program.attr,
+ NULL,
+};
+
+static const struct attribute_group fpga_attr_group = {
+ .attrs = fpga_attributes,
+};
+
+/*
+ * OpenFirmware Device Subsystem
+ */
+
+#define SYS_REG_VERSION 0x00
+#define SYS_REG_GEOGRAPHIC 0x10
+
+static bool dma_filter(struct dma_chan *chan, void *data)
+{
+ /*
+ * DMA Channel #0 is the only acceptable device
+ *
+ * This probably won't survive an unload/load cycle of the Freescale
+ * DMAEngine driver, but that won't be a problem
+ */
+ return chan->chan_id == 0 && chan->device->dev_id == 0;
+}
+
+static int fpga_of_remove(struct platform_device *op)
+{
+ struct fpga_dev *priv = dev_get_drvdata(&op->dev);
+ struct device *this_device = priv->miscdev.this_device;
+
+ sysfs_remove_group(&this_device->kobj, &fpga_attr_group);
+ misc_deregister(&priv->miscdev);
+
+ free_irq(priv->irq, priv);
+ iounmap(priv->immr);
+
+ fpga_disable_power_supplies(priv);
+ iounmap(priv->regs);
+
+ dma_release_channel(priv->chan);
+
+ /* Free any firmware image that has not been programmed */
+ fpga_drop_firmware_data(priv);
+
+ mutex_destroy(&priv->lock);
+ kfree(priv);
+
+ return 0;
+}
+
+static int fpga_of_probe(struct platform_device *op, const struct of_device_id *match)
+{
+ struct device_node *of_node = op->dev.of_node;
+ struct device *this_device;
+ struct fpga_dev *priv;
+ dma_cap_mask_t mask;
+ u32 ver;
+ int ret;
+
+ /* Allocate private data */
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(&op->dev, "Unable to allocate private data\n");
+ ret = -ENOMEM;
+ goto out_return;
+ }
+
+ /* Setup the miscdevice */
+ priv->miscdev.minor = MISC_DYNAMIC_MINOR;
+ priv->miscdev.name = drv_name;
+ priv->miscdev.fops = &fpga_fops;
+
+ dev_set_drvdata(&op->dev, priv);
+ priv->dev = &op->dev;
+ mutex_init(&priv->lock);
+ init_completion(&priv->completion);
+ videobuf_dma_init(&priv->vb);
+
+ dev_set_drvdata(priv->dev, priv);
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_MEMCPY, mask);
+ dma_cap_set(DMA_INTERRUPT, mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ dma_cap_set(DMA_SG, mask);
+
+ /* Get control of DMA channel #0 */
+ priv->chan = dma_request_channel(mask, dma_filter, NULL);
+ if (!priv->chan) {
+ dev_err(&op->dev, "Unable to acquire DMA channel #0\n");
+ ret = -ENODEV;
+ goto out_free_priv;
+ }
+
+ /* Remap the registers for use */
+ priv->regs = of_iomap(of_node, 0);
+ if (!priv->regs) {
+ dev_err(&op->dev, "Unable to ioremap registers\n");
+ ret = -ENOMEM;
+ goto out_dma_release_channel;
+ }
+
+ /* Remap the IMMR for use */
+ priv->immr = ioremap(get_immrbase(), 0x100000);
+ if (!priv->immr) {
+ dev_err(&op->dev, "Unable to ioremap IMMR\n");
+ ret = -ENOMEM;
+ goto out_unmap_regs;
+ }
+
+ /*
+ * Check that external DMA is configured
+ *
+ * U-Boot does this for us, but we should check it and bail out if
+ * there is a problem. Failing to have this register setup correctly
+ * will cause the DMA controller to transfer a single cacheline
+ * worth of data, then wedge itself.
+ */
+ if ((ioread32be(priv->immr + 0x114) & 0xE00) != 0xE00) {
+ dev_err(&op->dev, "External DMA control not configured\n");
+ ret = -ENODEV;
+ goto out_unmap_immr;
+ }
+
+ /*
+ * Check the CTL-CPLD version
+ *
+ * This driver uses the CTL-CPLD DATA-FPGA power sequencer, and we
+ * don't want to run on any version of the CTL-CPLD that does not use
+ * a compatible register layout.
+ *
+ * v2: changed register layout, added power sequencer
+ * v3: added glitch filter on the i2c overcurrent/overtemp outputs
+ */
+ ver = ioread8(priv->regs + 0x2000);
+ if (ver != 0x02 && ver != 0x03) {
+ dev_err(&op->dev, "CTL-CPLD is not version 0x02 or 0x03!\n");
+ ret = -ENODEV;
+ goto out_unmap_immr;
+ }
+
+ /* Set the exact size that the firmware image should be */
+ ver = ioread32be(priv->regs + SYS_REG_VERSION);
+ priv->fw_size = (ver & (1 << 18)) ? FW_SIZE_EP2S130 : FW_SIZE_EP2S90;
+
+ /* Find the correct IRQ number */
+ priv->irq = irq_of_parse_and_map(of_node, 0);
+ if (priv->irq == NO_IRQ) {
+ dev_err(&op->dev, "Unable to find IRQ line\n");
+ ret = -ENODEV;
+ goto out_unmap_immr;
+ }
+
+ /* Request the IRQ */
+ ret = request_irq(priv->irq, fpga_interrupt, IRQF_SHARED, drv_name, priv);
+ if (ret) {
+ dev_err(&op->dev, "Unable to request IRQ %d\n", priv->irq);
+ ret = -ENODEV;
+ goto out_irq_dispose_mapping;
+ }
+
+ /* Reset and stop the FPGA's, just in case */
+ fpga_do_stop(priv);
+
+ /* Register the miscdevice */
+ ret = misc_register(&priv->miscdev);
+ if (ret) {
+ dev_err(&op->dev, "Unable to register miscdevice\n");
+ goto out_free_irq;
+ }
+
+ /* Create the sysfs files */
+ this_device = priv->miscdev.this_device;
+ dev_set_drvdata(this_device, priv);
+ ret = sysfs_create_group(&this_device->kobj, &fpga_attr_group);
+ if (ret) {
+ dev_err(&op->dev, "Unable to create sysfs files\n");
+ goto out_misc_deregister;
+ }
+
+ dev_info(priv->dev, "CARMA FPGA Programmer: %s rev%s with %s FPGAs\n",
+ (ver & (1 << 17)) ? "Correlator" : "Digitizer",
+ (ver & (1 << 16)) ? "B" : "A",
+ (ver & (1 << 18)) ? "EP2S130" : "EP2S90");
+
+ return 0;
+
+out_misc_deregister:
+ misc_deregister(&priv->miscdev);
+out_free_irq:
+ free_irq(priv->irq, priv);
+out_irq_dispose_mapping:
+ irq_dispose_mapping(priv->irq);
+out_unmap_immr:
+ iounmap(priv->immr);
+out_unmap_regs:
+ iounmap(priv->regs);
+out_dma_release_channel:
+ dma_release_channel(priv->chan);
+out_free_priv:
+ mutex_destroy(&priv->lock);
+ kfree(priv);
+out_return:
+ return ret;
+}
+
+static struct of_device_id fpga_of_match[] = {
+ { .compatible = "carma,fpga-programmer", },
+ {},
+};
+
+static struct of_platform_driver fpga_of_driver = {
+ .probe = fpga_of_probe,
+ .remove = fpga_of_remove,
+ .driver = {
+ .name = drv_name,
+ .of_match_table = fpga_of_match,
+ .owner = THIS_MODULE,
+ },
+};
+
+/*
+ * Module Init / Exit
+ */
+
+static int __init fpga_init(void)
+{
+ led_trigger_register_simple("fpga", &ledtrig_fpga);
+ return of_register_platform_driver(&fpga_of_driver);
+}
+
+static void __exit fpga_exit(void)
+{
+ of_unregister_platform_driver(&fpga_of_driver);
+ led_trigger_unregister_simple(ledtrig_fpga);
+}
+
+MODULE_AUTHOR("Ira W. Snyder <iws at ovro.caltech.edu>");
+MODULE_DESCRIPTION("CARMA Board DATA-FPGA Programmer");
+MODULE_LICENSE("GPL");
+
+module_init(fpga_init);
+module_exit(fpga_exit);
--
1.7.3.4
More information about the Linuxppc-dev
mailing list