kvm PCI assignment & VFIO ramblings

[aafabbri]

On 8/20/11 9:51 AM, "Alex Williamson" <alex.williamson at redhat.com> wrote:

> We had an extremely productive VFIO BoF on Monday.  Here's my attempt to
> capture the plan that I think we agreed to:
> 
> We need to address both the description and enforcement of device
> groups.  Groups are formed any time the iommu does not have resolution
> between a set of devices.  On x86, this typically happens when a
> PCI-to-PCI bridge exists between the set of devices and the iommu.  For
> Power, partitionable endpoints define a group.  Grouping information
> needs to be exposed for both userspace and kernel internal usage.  This
> will be a sysfs attribute setup by the iommu drivers.  Perhaps:
> 
> # cat /sys/devices/pci0000:00/0000:00:19.0/iommu_group
> 42
> 
> (I use a PCI example here, but attribute should not be PCI specific)
> 
> From there we have a few options.  In the BoF we discussed a model where
> binding a device to vfio creates a /dev/vfio$GROUP character device
> file.  This "group" fd provides provides dma mapping ioctls as well as
> ioctls to enumerate and return a "device" fd for each attached member of
> the group (similar to KVM_CREATE_VCPU).  We enforce grouping by
> returning an error on open() of the group fd if there are members of the
> group not bound to the vfio driver.

Sounds reasonable.

> Each device fd would then support a
> similar set of ioctls and mapping (mmio/pio/config) interface as current
> vfio, except for the obvious domain and dma ioctls superseded by the
> group fd.
> 
> Another valid model might be that /dev/vfio/$GROUP is created for all
> groups when the vfio module is loaded.  The group fd would allow open()
> and some set of iommu querying and device enumeration ioctls, but would
> error on dma mapping and retrieving device fds until all of the group
> devices are bound to the vfio driver.
> 
> In either case, the uiommu interface is removed entirely since dma
> mapping is done via the group fd.

The loss in generality is unfortunate. I'd like to be able to support
arbitrary iommu domain <-> device assignment.  One way to do this would be
to keep uiommu, but to return an error if someone tries to assign more than
one uiommu context to devices in the same group.


-Aaron

> As necessary in the future, we can
> define a more high performance dma mapping interface for streaming dma
> via the group fd.  I expect we'll also include architecture specific
> group ioctls to describe features and capabilities of the iommu.  The
> group fd will need to prevent concurrent open()s to maintain a 1:1 group
> to userspace process ownership model.
> 
> Also on the table is supporting non-PCI devices with vfio.  To do this,
> we need to generalize the read/write/mmap and irq eventfd interfaces.
> We could keep the same model of segmenting the device fd address space,
> perhaps adding ioctls to define the segment offset bit position or we
> could split each region into it's own fd (VFIO_GET_PCI_BAR_FD(0),
> VFIO_GET_PCI_CONFIG_FD(), VFIO_GET_MMIO_FD(3)), though we're already
> suffering some degree of fd bloat (group fd, device fd(s), interrupt
> event fd(s), per resource fd, etc).  For interrupts we can overload
> VFIO_SET_IRQ_EVENTFD to be either PCI INTx or non-PCI irq (do non-PCI
> devices support MSI?).
> 
> For qemu, these changes imply we'd only support a model where we have a
> 1:1 group to iommu domain.  The current vfio driver could probably
> become vfio-pci as we might end up with more target specific vfio
> drivers for non-pci.  PCI should be able to maintain a simple -device
> vfio-pci,host=bb:dd.f to enable hotplug of individual devices.  We'll
> need to come up with extra options when we need to expose groups to
> guest for pvdma.
> 
> Hope that captures it, feel free to jump in with corrections and
> suggestions.  Thanks,
> 
> Alex
>