[PATCH v11 6/6] powerpc: Add flexcan device support for p1010rdb.

[Robin Holt]

On Thu, Aug 11, 2011 at 12:41:34PM -0500, Kumar Gala wrote:
> 
> On Aug 11, 2011, at 11:07 AM, Robin Holt wrote:
> 
> > Allow the p1010 processor to select the flexcan network driver.
> > 
> > Signed-off-by: Robin Holt <holt at sgi.com>
> > Acked-by: Marc Kleine-Budde <mkl at pengutronix.de>,
> > Acked-by: Wolfgang Grandegger <wg at grandegger.com>,
> > Cc: U Bhaskar-B22300 <B22300 at freescale.com>
> > Cc: socketcan-core at lists.berlios.de,
> > Cc: netdev at vger.kernel.org,
> > Cc: PPC list <linuxppc-dev at lists.ozlabs.org>
> > Cc: Kumar Gala <galak at kernel.crashing.org>
> > ---
> > arch/powerpc/boot/dts/p1010rdb.dts  |    8 ++++++++
> > arch/powerpc/platforms/85xx/Kconfig |    2 ++
> > 2 files changed, 10 insertions(+), 0 deletions(-)
> > 
> > diff --git a/arch/powerpc/boot/dts/p1010rdb.dts b/arch/powerpc/boot/dts/p1010rdb.dts
> > index d6c669c..df89b60 100644
> > --- a/arch/powerpc/boot/dts/p1010rdb.dts
> > +++ b/arch/powerpc/boot/dts/p1010rdb.dts
> > @@ -171,6 +171,14 @@
> > 			};
> > 		};
> > 
> > +		can at 1c000 {
> > +			clock-frequency = <0x0bebc1fc>;
> > +		};
> > +
> > +		can1: can at 1d000 {
> > +			clock-frequency = <0x0bebc1fc>;
> > +		};
> > +
> 
> set them to 0, as we expect u-boot to fill them in.

Done.

> 
> > 		usb at 22000 {
> > 			phy_type = "utmi";
> > 		};
> > diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
> > index 498534c..c4304ae 100644
> > --- a/arch/powerpc/platforms/85xx/Kconfig
> > +++ b/arch/powerpc/platforms/85xx/Kconfig
> > @@ -70,6 +70,8 @@ config MPC85xx_RDB
> > config P1010_RDB
> > 	bool "Freescale P1010RDB"
> > 	select DEFAULT_UIMAGE
> > +	select HAVE_CAN_FLEXCAN if NET && CAN
> > +	select PPC_CLOCK if CAN_FLEXCAN
> 
> Can you move this to arch/powerpc/Kconfig & FSL_SOC instead.

I am not sure.  FSL_SOC seems to come with any of the freescale system
on a chip.  I would not be that worried, about the flexcan build as
I think that is sufficiently agostic where we will not see problems,
but now we could end up with build failures on any of the other configs
which select CAN_FLEXCAN.  I would normally want to do all those builds,
but there is no way I would know how to do that with my limited knowledge
of powerpc and freescale.

If you are comfortable with that, I will happily make the change.

Thanks,
Robin