pci_request_regions() failure

[tiejun.chen]

Ravi Gupta wrote:
> Hi Tiejun,
> 
> Thanks for the reply.
> 
> 
> Your PCI device should be one virtual device so I think the above should be
>> as
>> we understood. You know 0x00000000 ~ 0x00003ffff should not be allowed to
>> reserved.
>>
> 
> Can you explain a little more that what do you mean by "Your PCI device
> should be one virtual device"?

I means your PCI example from LDD3. That is only emulated for configure space.
No BARs, no irq, ......

> 
> 
>> I think you should do the following sequence in the probe function of your
>> PCI
>> driver.
>>
>> 1. pci_enable_device(pdev);
>> 2. pci_request_regions(pdev, DRV_NAME);
>> 3. pci_set_master(pdev);
>> ......
>>
>> Okay, I have  changed my drive code to follow this sequence, but still no
> success. It fails with the same errors as before.

I means you do this on your real PCI device driver. When you fix my comments in
below, try to update this on your PCI device e250 again.

> 
> # insmod ./pci_skel.ko
> PCI driver: Init function
> PCI driver: Probe function
> pci_skel 0001:02:00.0: device not available (can't reserve [mem
> 0x00000000-0x0003ffff])
> Unable to Enable PCI device:-22
> pci_skel: probe of 0001:02:00.0 failed with error -22
> 
> Looks we need some pci_fixup to modify them. Firstly I think you'd better
>> 'zero'
>> all BARs of your PCI device on the function, pci_scan_device, on the file,
>> drivers/pci/probe.c. On there you can dedicate that once your device is
>> probed.
>> Please check the each BAR's value again after the above fix.
>>
>>
> Okay, I have set the BARs with all zeros in the pci_scan_device() function.
> Below is the diff of the changes done by me.
> 
> --- /data/sources/linux-2.6.35/drivers/pci/probe.c  2010-08-02
> 03:41:14.000000000 +0530
> +++ probe.c 2010-09-08 14:45:40.000000000 +0530
> @@ -1172,6 +1172,45 @@ static struct pci_dev *pci_scan_device(s
>     }
>   }
> 
> + printk(KERN_WARNING "pci : vendor id = 0x%x\n", l & 0xffff);
> + if ((l & 0xffff) == 0x1204) {
> +   /* zero's all BAR registers */
> +   printk(KERN_WARNING "pci %04x:%02x:%02x.%d: trying to set all zeros in "
> +       "BARs\n", pci_domain_nr(bus),
> +       bus->number, PCI_SLOT(devfn),
> +       PCI_FUNC(devfn));
> +
> +   if(pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_0, 0x0) ||
> +       pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_1, 0x0) ||
> +       pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_2, 0x0) ||
> +       pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_3, 0x0) ||
> +       pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_4, 0x0) ||
> +       pci_bus_write_config_dword(bus, devfn, PCI_BASE_ADDRESS_5, 0x0)) {
> +
> +     printk(KERN_WARNING "pci %04x:%02x:%02x.%d: failed to reset bits"
> +         "of BARs\n", pci_domain_nr(bus),
> +         bus->number, PCI_SLOT(devfn),
> +         PCI_FUNC(devfn));
> +     return NULL;
> +   }
> + }
> +
>   dev = alloc_pci_dev();
>   if (!dev)
>     return NULL;
> 
> The difference  I have seen in the dmesg is that the following two messages
> are not coming now.
> 
> PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
> PCI: Cannot allocate resource region 1 of device 0001:02:00.0, will remap

Good.

> 
> But my driver is still fails with the same error as before. I am attaching
> the new dmesg log.
> 
> Dmesg with all BARs set to zero
> ================================================================
> Using MPC837x RDB/WLAN machine description
> Initializing cgroup subsys cpuset
> Initializing cgroup subsys cpu
> Linux version 2.6.35 (okapi at okapi) (gcc version 4.2.3 (Sourcery G++ Lite
> 4.2-171)) #28 Wed Sep 8 13:20:27 IST 2010
> Found initrd at 0xcf46c000:0xcf7b05b7
> Found legacy serial port 0 for /immr at e0000000/serial at 4500
>   mem=e0004500, taddr=e0004500, irq=0, clk=400000002, speed=0
> Found legacy serial port 1 for /immr at e0000000/serial at 4600
>   mem=e0004600, taddr=e0004600, irq=0, clk=400000002, speed=0
> bootconsole [udbg0] enabled
> Found FSL PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
> PCI host bridge /pci at e0008500 (primary) ranges:
>  MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000
>  MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 Prefetch
>   IO 0x00000000e0300000..0x00000000e03fffff -> 0x0000000000000000
> No pci config register base in dev tree, using default
> Found FSL PCI host bridge at 0x00000000e0009000. Firmware bus number: 0->255
> PCI host bridge /pcie at e0009000  ranges:
>  MEM 0x00000000a8000000..0x00000000b7ffffff -> 0x00000000a8000000
>   IO 0x00000000b8000000..0x00000000b87fffff -> 0x0000000000000000
> No pci config register base in dev tree, using default
> Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->255
> PCI host bridge /pcie at e000a000  ranges:
>  MEM 0x00000000c8000000..0x00000000d7ffffff -> 0x00000000c8000000
>   IO 0x00000000d8000000..0x00000000d87fffff -> 0x0000000000000000
> Top of RAM: 0x10000000, Total RAM: 0x10000000
> Memory hole size: 0MB
> Zone PFN ranges:
>   DMA      0x00000000 -> 0x00010000
>   Normal   empty
>   HighMem  empty
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
>     0: 0x00000000 -> 0x00010000
> On node 0 totalpages: 65536
> free_area_init_node: node 0, pgdat c04265e8, node_mem_map c0800000
>   DMA zone: 512 pages used for memmap
>   DMA zone: 0 pages reserved
>   DMA zone: 65024 pages, LIFO batch:15
> Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
> Kernel command line: root=/dev/ram ramdisk_size=120000 rw ip=10.20.50.230:10
> .20.50.70:10.20.50.50:255.255.0.0:PowerQUICC:eth0:off console=ttyS0,115200
> mtdparts=nand:4m(kernel),-(jffs2)
> PID hash table entries: 1024 (order: 0, 4096 bytes)
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> High memory: 0k
> Memory: 249972k/262144k available (4064k kernel code, 12172k reserved, 244k
> data, 2187k bss, 188k init)
> Kernel virtual memory layout:
>   * 0xfffcf000..0xfffff000  : fixmap
>   * 0xff800000..0xffc00000  : highmem PTEs
>   * 0xfe6f7000..0xff800000  : early ioremap
>   * 0xd1000000..0xfe6f7000  : vmalloc & ioremap
> Hierarchical RCU implementation.
>     RCU-based detection of stalled CPUs is disabled.
>     Verbose stalled-CPUs detection is disabled.
> NR_IRQS:512
> IPIC (128 IRQ sources) at d1000700
> time_init: decrementer frequency = 100.000000 MHz
> time_init: processor frequency   = 800.000004 MHz
> clocksource: timebase mult[2800000] shift[22] registered
> clockevent: decrementer mult[19999999] shift[32] cpu[0]
> Console: colour dummy device 80x25
> pid_max: default: 32768 minimum: 301
> Security Framework initialized
> SELinux:  Disabled at boot.
> Mount-cache hash table entries: 512
> Initializing cgroup subsys ns
> Initializing cgroup subsys cpuacct
> Initializing cgroup subsys devices
> NET: Registered protocol family 16
> irq: irq 38 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 38
> __irq_set_trigger: setting type, irq = 38, flags = 8
> ipic_set_irq_type function, with virq = 38, flow = 8
> irq: irq 74 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 74
> __irq_set_trigger: setting type, irq = 74, flags = 8
> ipic_set_irq_type function, with virq = 74, flow = 8
> irq: irq 75 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 75
> __irq_set_trigger: setting type, irq = 75, flags = 8
> ipic_set_irq_type function, with virq = 75, flow = 8
> PCI: Probing PCI hardware
> PCI: Scanning PHB /pci at e0008500
> PCI: PHB IO resource    = 0000000000000000-00000000000fffff [100]
> PCI: PHB MEM resource 0 = 0000000090000000-000000009fffffff [200]
> PCI: PHB MEM resource 1 = 0000000080000000-000000008fffffff [2200]
> PCI: PHB MEM offset     = 0000000000000000
> PCI: PHB IO  offset     = 00000000
>     probe mode: 0
> pci_bus 0000:00: scanning bus
> pci : vendor id = 0x1957
> pci 0000:00:00.0: found [1957:00c6] class 000b20 header type 00
> pci 0000:00:00.0: reg 10: [mem 0x00000000-0x000fffff]
> pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0fffffff 64bit pref]
> pci 0000:00:00.0: calling fixup_hide_host_resource_fsl+0x0/0x58
> pci 0000:00:00.0: calling pcibios_fixup_resources+0x0/0x180
> pci 0000:00:00.0: calling quirk_fsl_pcie_header+0x0/0x48
> pci 0000:00:00.0: calling quirk_resource_alignment+0x0/0x1c0
> pci 0000:00:00.0: supports D1 D2
> pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:00.0: PME# disabled
> pci_bus 0000:00: fixups for bus
> PCI: Fixup bus devices 0 (PHB)
> PCI: Try to map irq for 0000:00:00.0...
> pci_bus 0000:00: bus scan returning with max=00
> PCI: Scanning PHB /pcie at e0009000
> PCI: PHB IO resource    = 00000000ff7fe000-00000000ffffdfff [100]
> PCI: PHB MEM resource 0 = 00000000a8000000-00000000b7ffffff [200]
> PCI: PHB MEM offset     = 0000000000000000
> PCI: PHB IO  offset     = ff7fe000
>     probe mode: 0
> pci_bus 0001:01: scanning bus
> pci : vendor id = 0x1957
> pci 0001:01:00.0: found [1957:00c6] class 000b20 header type 01
> pci 0001:01:00.0: ignoring class b20 (doesn't match header type 01)
> pci 0001:01:00.0: calling fixup_hide_host_resource_fsl+0x0/0x58
> pci 0001:01:00.0: calling pcibios_fixup_resources+0x0/0x180
> pci 0001:01:00.0: calling quirk_fsl_pcie_header+0x0/0x48
> pci 0001:01:00.0: calling quirk_resource_alignment+0x0/0x1c0
> pci 0001:01:00.0: supports D1 D2
> pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot
> pci 0001:01:00.0: PME# disabled
> pci_bus 0001:01: fixups for bus
> PCI: Fixup bus devices 1 (PHB)
> PCI: Try to map irq for 0001:01:00.0...
> pci 0001:01:00.0: scanning [bus 01-ff] behind bridge, pass 0
> pci 0001:01:00.0: bus configuration invalid, reconfiguring
> pci 0001:01:00.0: scanning [bus 00-00] behind bridge, pass 1
> pci_bus 0001:02: scanning bus
> pci : vendor id = 0x1204
> pci 0001:02:00.0: trying to set all zeros in BARs
> pci 0001:02:00.0: found [1204:e250] class 000000 header type 00
> pci 0001:02:00.0: reg 10: [mem 0x00000000-0x0003ffff]
> pci 0001:02:00.0: reg 14: [mem 0x00000000-0x0003ffff]

Looks BAR0 and BAR1 are used for your PCI device. So if normal, the memory range
of your PCI device will be [mem 0xa8000000-0xa803ffff] and [mem
0xa8040000-0xa807ffff] as we pexpect.

You can print this pci_resource_start(pdev, bar), pci_resource_len(pdev, bar)
from the function, __pci_request_region, on the file drivers/pci/pci.c. Please
check this as well.

> pci 0001:02:00.0: calling pcibios_fixup_resources+0x0/0x180
> PCI:0001:02:00.0 Resource 0 0000000000000000-000000000003ffff [40200] is
> unassigned
> PCI:0001:02:00.0 Resource 1 0000000000000000-000000000003ffff [40200] is
> unassigned
> pci 0001:02:00.0: calling quirk_resource_alignment+0x0/0x1c0
> pci_bus 0001:02: fixups for bus
> pci 0001:01:00.0: PCI bridge to [bus 02-ff]
> pci 0001:01:00.0:   bridge window [io  0x0000-0x0000] (disabled)
> pci 0001:01:00.0:   bridge window [mem 0x00000000-0x000fffff] (disabled)
> pci 0001:01:00.0:   bridge window [mem 0x00000000-0x000fffff pref]

Omm.

Often we always disable this pref windows so please disable this window. Try use
the following ways to clear PCI_PREF_MEMORY_BASE and PCI_PREF_MEMORY_LIMIT.
------
        pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, 0);
        pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, 0);

> (disabled)
> PCI: Fixup bus devices 2 (0001:01:00.0)
> PCI: Try to map irq for 0001:02:00.0...
>  Got one, spec 2 cells (0x00000001 0x00000008...) on /immr at e0000000
> /interrupt-controller at 700
> irq: irq 1 on host /immr at e0000000/interrupt-controller at 700 mapped to virtual
> irq 16
> __irq_set_trigger: setting type, irq = 16, flags = 8
> ipic_set_irq_type function, with virq = 16, flow = 8
>  Mapped to linux irq 16
> pci_bus 0001:02: bus scan returning with max=02
> pci_bus 0001:01: bus scan returning with max=02
> PCI: Scanning PHB /pcie at e000a000
> PCI: PHB IO resource    = 00000000feffc000-00000000ff7fbfff [100]
> PCI: PHB MEM resource 0 = 00000000c8000000-00000000d7ffffff [200]
> PCI: PHB MEM offset     = 0000000000000000
> PCI: PHB IO  offset     = feffc000
>     probe mode: 0
> pci_bus 0002:03: scanning bus
> pci_bus 0002:03: fixups for bus
> PCI: Fixup bus devices 3 (PHB)
> pci_bus 0002:03: bus scan returning with max=03
> PCI->OF bus map:
> 0 -> 0
> 1 -> 0
> 3 -> 0
> PCI: Allocating bus resources for 0000:00...
> PCI: PHB (bus 0) bridge rsrc 0: 0000000000000000-00000000000fffff [0x100],
> parent c03fe5a0 (PCI IO)
> PCI: PHB (bus 0) bridge rsrc 1: 0000000090000000-000000009fffffff [0x200],
> parent c03fe584 (PCI mem)
> PCI: PHB (bus 0) bridge rsrc 2: 0000000080000000-000000008fffffff [0x2200],
> parent c03fe584 (PCI mem)
> PCI: Allocating bus resources for 0001:01...
> PCI: PHB (bus 1) bridge rsrc 0: 00000000ff7fe000-00000000ffffdfff [0x100],
> parent c03fe5a0 (PCI IO)
> PCI: PHB (bus 1) bridge rsrc 1: 00000000a8000000-00000000b7ffffff [0x200],
> parent c03fe584 (PCI mem)
> PCI: Allocating bus resources for 0001:02...
> PCI: Allocating bus resources for 0002:03...
> PCI: PHB (bus 3) bridge rsrc 0: 00000000feffc000-00000000ff7fbfff [0x100],
> parent c03fe5a0 (PCI IO)
> PCI: PHB (bus 3) bridge rsrc 1: 00000000c8000000-00000000d7ffffff [0x200],
> parent c03fe584 (PCI mem)
> Reserving legacy ranges for domain 0000
> Candidate legacy IO: [io  0x0000-0x0fff]
> hose mem offset: 0000000000000000
> hose mem res: [mem 0x90000000-0x9fffffff]
> hose mem res: [mem 0x80000000-0x8fffffff pref]
> Reserving legacy ranges for domain 0001
> Candidate legacy IO: [io  0xff7fe000-0xff7fefff]
> hose mem offset: 0000000000000000
> hose mem res: [mem 0xa8000000-0xb7ffffff]
> Reserving legacy ranges for domain 0002
> Candidate legacy IO: [io  0xfeffc000-0xfeffcfff]
> hose mem offset: 0000000000000000
> hose mem res: [mem 0xc8000000-0xd7ffffff]
> PCI: Assigning unassigned resources...
> pci 0001:01:00.0: BAR 8: assigned [mem 0xa8000000-0xa80fffff]

When you disable that pref window I think everything should be good since it's
not allowed to allocate a non-prefetching resource from a pre-fetching area and
the kernel can't assign mem pref (size 0x100000). And here your pci devie will
be assigned as [mem 0xa8000000-0xa803ffff] and [mem 0xa8040000-0xa807ffff] for
BAR0  & BAR1.

> pci 0001:01:00.0: PCI bridge to [bus 02-02]
> pci 0001:01:00.0:   bridge window [io  disabled]
> pci 0001:01:00.0:   bridge window [mem 0xa8000000-0xa80fffff]

Now the above window will be allocate as PCI bus resource 0xa8000000 ~ 0xb7ffffff.

> pci 0001:01:00.0:   bridge window [mem pref disabled]
> pci_bus 0000:00: resource 0 [io  0x0000-0xfffff]
> pci_bus 0000:00: resource 1 [mem 0x90000000-0x9fffffff]
> pci_bus 0000:00: resource 2 [mem 0x80000000-0x8fffffff pref]
> pci_bus 0001:01: resource 0 [io  0xff7fe000-0xffffdfff]
> pci_bus 0001:01: resource 1 [mem 0xa8000000-0xb7ffffff]
> pci_bus 0001:02: resource 1 [mem 0xa8000000-0xa80fffff]

If you can do the above assign resource correctly, I think this should be same
as 0001:01 [mem 0xa8000000-0xb7ffffff] since they are in same PCI domain 0001.
As the secondary bus within the PCI domain 0001, 02 should have full range from
its parent bus because there is only one bus/device on the 02 bus level.

As a summary your issue should be the bootloader and looks your bootloader don't
initial an appropriate state for PCIE controller.

Best Reards
Tiejun

> pci_bus 0002:03: resource 0 [io  0xfeffc000-0xff7fbfff]
> pci_bus 0002:03: resource 1 [mem 0xc8000000-0xd7ffffff]
> Registering qe_ic with sysfs...
> Registering ipic with sysfs...
> bio: create slab <bio-0> at 0
> vgaarb: loaded
> SCSI subsystem initialized
> Switching to clocksource timebase
> NET: Registered protocol family 2
> IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> TCP reno registered
> UDP hash table entries: 256 (order: 0, 4096 bytes)
> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> NET: Registered protocol family 1
> pci 0000:00:00.0: calling quirk_cardbus_legacy+0x0/0x44
> pci 0000:00:00.0: calling quirk_usb_early_handoff+0x0/0x740
> pci 0001:01:00.0: calling quirk_cardbus_legacy+0x0/0x44
> pci 0001:01:00.0: calling quirk_usb_early_handoff+0x0/0x740
> pci 0001:02:00.0: calling quirk_cardbus_legacy+0x0/0x44
> pci 0001:02:00.0: calling quirk_usb_early_handoff+0x0/0x740
> PCI: CLS 32 bytes, default 32
> Trying to unpack rootfs image as initramfs...
> rootfs image is not initramfs (no cpio magic); looks like an initrd
> Freeing initrd memory: 3345k freed
> irq: irq 9 on host /immr at e0000000/interrupt-controller at 700 mapped to virtual
> irq 17
> __irq_set_trigger: setting type, irq = 17, flags = 8
> ipic_set_irq_type function, with virq = 17, flow = 8
> irq: irq 10 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 18
> __irq_set_trigger: setting type, irq = 18, flags = 8
> ipic_set_irq_type function, with virq = 18, flow = 8
> irq: irq 80 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 80
> __irq_set_trigger: setting type, irq = 80, flags = 8
> ipic_set_irq_type function, with virq = 80, flow = 8
> audit: initializing netlink socket (disabled)
> type=2000 audit(0.212:1): initialized
> JFFS2 version 2.2. (NAND) � 2001-2006 Red Hat, Inc.
> SGI XFS with security attributes, large block/inode numbers, no debug
> enabled
> msgmni has been set to 494
> alg: No test for cipher_null (cipher_null-generic)
> alg: No test for ecb(cipher_null) (ecb-cipher_null)
> alg: No test for digest_null (digest_null-generic)
> alg: No test for compress_null (compress_null-generic)
> alg: No test for stdrng (krng)
> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
> serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 17) is a 16550A
> console [ttyS0] enabled, bootconsole disabled
> serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 18) is a 16550A
> brd: module loaded
> of_mpc8xxx_spi_probe function called.
> irq: irq 16 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 19
> __irq_set_trigger: setting type, irq = 19, flags = 8
> ipic_set_irq_type function, with virq = 19, flow = 8
> mpc8xxx_spi_probe function called.
> mpc8xxx_spi e0007000.spi: at 0xd1078000 (irq = 19), CPU mode
> irq: irq 32 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 32
> __irq_set_trigger: setting type, irq = 32, flags = 8
> ipic_set_irq_type function, with virq = 32, flow = 8
> irq: irq 33 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 33
> __irq_set_trigger: setting type, irq = 33, flags = 8
> ipic_set_irq_type function, with virq = 33, flow = 8
> irq: irq 34 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 34
> __irq_set_trigger: setting type, irq = 34, flags = 8
> ipic_set_irq_type function, with virq = 34, flow = 8
> eth0: Gianfar Ethernet Controller Version 1.2, 04:00:00:00:00:0a
> eth0: Running with NAPI enabled
> eth0: RX BD ring size for Q[0]: 256
> eth0: TX BD ring size for Q[0]: 256
> irq: irq 35 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 35
> __irq_set_trigger: setting type, irq = 35, flags = 8
> ipic_set_irq_type function, with virq = 35, flow = 8
> irq: irq 36 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 36
> __irq_set_trigger: setting type, irq = 36, flags = 8
> ipic_set_irq_type function, with virq = 36, flow = 8
> irq: irq 37 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 37
> __irq_set_trigger: setting type, irq = 37, flags = 8
> ipic_set_irq_type function, with virq = 37, flow = 8
> eth1: Gianfar Ethernet Controller Version 1.2, 00:00:00:00:00:00
> eth1: Running with NAPI enabled
> eth1: RX BD ring size for Q[0]: 256
> eth1: TX BD ring size for Q[0]: 256
> ucc_geth: QE UCC Gigabit Ethernet Controller
> Freescale PowerQUICC MII Bus: probed
> irq: irq 17 on host /immr at e0000000/interrupt-controller at 700 mapped to
> virtual irq 20
> __irq_set_trigger: setting type, irq = 20, flags = 8
> ipic_set_irq_type function, with virq = 20, flow = 8
> Freescale PowerQUICC MII Bus: probed
> mice: PS/2 mouse device common for all mice
> Skipping unavailable LED gpio -19 (pwr)
> Skipping unavailable LED gpio -19 (hdd)
> TCP cubic registered
> NET: Registered protocol family 17
> registered taskstats version 1
> drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
> RAMDISK: gzip image found at block 0
> VFS: Mounted root (ext2 filesystem) on device 1:0.
> Freeing unused kernel memory: 188k init
> PHY: mdio at e0024520:02 - Link is Up - 10/Half
> ================================================================
> 
> Regards,
> Ravi
> 
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev