PHY/FEC Network adapter failed to initialize on MPC52xx Board

[tiejun.chen]

Peter wrote:
> Hi all
> 
> I got completely stuck with a network adapter problem on my
> ppc board (MPC52xx style). The ntwork adapter does not seem
> to intialize correctly when booted without 'help from uboot'
> 

Looks your problem is very similar to one I replied here not long ago :) That is
also issued from MPC5200. And I remember there was a wrong Port Multiplex
Configuration.

If possible maybe you can check the email subjected "Problem Ethernet
Initialization MPC5200 +  LXT971A" on linuxppc-dev list.

Hope its useful.

Tiejun

> The adapter works properly when I first use it with uboot. E.g.
> using tftp to load the kernel or just issuing a dummy sntp
> command. It does not get intialized if I boot linux without
> using any network relevant command in ubboot
> 
> The difference manifests on the boot message: (working)
> PHY working
> ...
> mpc52xx MII bus: probed
> TCP cubic registered
> NET: Registered protocol family 17
> IP-Config: Complete:
>      device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
>      host=192.168.1.245, domain=, nis-domain=(none),
>      bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
> Looking up port of RPC 100003/2 on 192.168.1.244
> Looking up port of RPC 100005/1 on 192.168.1.244
> VFS: Mounted root (nfs filesystem) on device 0:11.
> Freeing unused kernel memory: 124k init
> PHY: f0003000:00 - Link is Up - 100/Full
> 
> # ping 192.168.1.2  returns proper results.
> 
> PHY Not working:
> ...
> mpc52xx MII bus: probed
> TCP cubic registered
> NET: Registered protocol family 17
> IP-Config: Complete:
>      device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
>      host=192.168.1.245, domain=, nis-domain=(none),
>      bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=
> VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
> Freeing unused kernel memory: 124k init
> 
> # ping 192.168.1.2  hangs
> 
> 
> The second snipped does not have "Looking up.." messages because it
> boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full"
> which does not appear at the failing case.
> 
> Linux Version is 2.6.35.7 patched with xenomai 2.5
> U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
> 
> Linux configuration see below: ( i left most entries out that are not set)
> I also experimented with different settings but finally only
> CONFIG_FEC_MPC52xx=y  and CONFIG_FEC_MPC52xx_MDIO=y
> seem to be of any relevance. If both are set, the adapter works
> when initialized by uboot.
> 
> Any help or tips will be very much appreciated,
> 
> Regards, Peter
> 
> 
> Linux .config
> 
> ...
> #
> # Platform support
> #
> # CONFIG_PPC_CHRP is not set
> # CONFIG_MPC5121_ADS is not set
> # CONFIG_MPC5121_GENERIC is not set
> CONFIG_PPC_MPC52xx=y
> CONFIG_PPC_MPC5200_SIMPLE=y
> # CONFIG_PPC_EFIKA is not set
> CONFIG_PPC_LITE5200=y
> # CONFIG_PPC_MEDIA5200 is not set
> CONFIG_PPC_MPC5200_BUGFIX=y
> # CONFIG_PPC_MPC5200_GPIO is not set
> CONFIG_PPC_MPC5200_LPBFIFO=y
> 
> CONFIG_PPC_BESTCOMM=y
> CONFIG_PPC_BESTCOMM_FEC=y
> CONFIG_PPC_BESTCOMM_GEN_BD=y
> # CONFIG_SIMPLE_GPIO is not set
> ..
> # Bus options
> #
> CONFIG_ZONE_DMA=y
> CONFIG_NEED_SG_DMA_LENGTH=y
> CONFIG_GENERIC_ISA_DMA=y
> CONFIG_PPC_PCI_CHOICE=y
> ...
> #
> # Generic Driver Options
> #
> CONFIG_STANDALONE=y
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> CONFIG_MTD=y
> CONFIG_MTD_PARTITIONS=y
> CONFIG_MTD_CMDLINE_PARTS=y
> 
> #
> # MII PHY device drivers
> #
> CONFIG_LXT_PHY=y                        ## Does not seem to have any influence
> CONFIG_NET_ETHERNET=y
> CONFIG_MII=y
> CONFIG_ETHOC=y                           ## Does not seem to have any influence
> CONFIG_FEC_MPC52xx=y              ## Must be Y in roder to get adapter working with uboot's init
> CONFIG_FEC_MPC52xx_MDIO=y  ## Must be Y in roder to get adapter working with uboot's init