[PATCH v3 10/11] powerpc/mpc5121: update mpc5121ads DTS
Anatolij Gustschin
agust at denx.de
Sat Feb 6 00:42:56 EST 2010
Collects several changes needed after applying
previous mpc5121 platform and driver patches:
- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
- use "fsl,mpc5121-usb2-dr" compatible property only
- remove "port0" and "port1" properties as these are only used
for multi-port host(MHP) module which is not available
on MPC5121.
- use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
USB node for internal PHY to specify polarities
of the appropriate port pins.
Signed-off-by: Piotr Ziecik <kosmo at semihalf.com>
Signed-off-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: Detlev Zundel <dzu at denx.de>
Signed-off-by: Anatolij Gustschin <agust at denx.de>
Cc: Grant Likely <grant.likely at secretlab.ca>
---
Changes since v2:
- update USB nodes, drop "fsl-usb2-dr" property and
use fsl,mpc5121-usb2-dr" only
Changes since v1:
- move RTC node for m41t61 RTC to the node for I2C0
- add nodes for AD74114 and AT24C32CD3 devices
- remove obsolete "cell-index" properties from i2c nodes
and add "fsl,preserve-clocking" property
- Clean up CAN nodes
- prefix USB properties with 'fsl,'
arch/powerpc/boot/dts/mpc5121ads.dts | 55 ++++++++++++++++++++-------------
1 files changed, 33 insertions(+), 22 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc5121ads.dts b/arch/powerpc/boot/dts/mpc5121ads.dts
index c353dac..d2b2db7 100644
--- a/arch/powerpc/boot/dts/mpc5121ads.dts
+++ b/arch/powerpc/boot/dts/mpc5121ads.dts
@@ -62,17 +62,12 @@
interrupt-parent = < &ipic >;
#address-cells = <1>;
#size-cells = <1>;
- bank-width = <1>;
// ADS has two Hynix 512MB Nand flash chips in a single
- // stacked package .
+ // stacked package.
chips = <2>;
- nand0 at 0 {
- label = "nand0";
- reg = <0x00000000 0x02000000>; // first 32 MB of chip 0
- };
- nand1 at 20000000 {
- label = "nand1";
- reg = <0x20000000 0x02000000>; // first 32 MB of chip 1
+ nand at 0 {
+ label = "nand";
+ reg = <0x00000000 0x40000000>; // 512MB + 512MB
};
};
@@ -166,6 +161,11 @@
interrupt-parent = < &ipic >;
};
+ reset at e00 { // Reset module
+ compatible = "fsl,mpc5121-reset";
+ reg = <0xe00 0x100>;
+ };
+
clock at f00 { // Clock control
compatible = "fsl,mpc5121-clock";
reg = <0xf00 0x100>;
@@ -185,17 +185,15 @@
interrupt-parent = < &ipic >;
};
- mscan at 1300 {
+ can at 1300 {
compatible = "fsl,mpc5121-mscan";
- cell-index = <0>;
interrupts = <12 0x8>;
interrupt-parent = < &ipic >;
reg = <0x1300 0x80>;
};
- mscan at 1380 {
+ can at 1380 {
compatible = "fsl,mpc5121-mscan";
- cell-index = <1>;
interrupts = <13 0x8>;
interrupt-parent = < &ipic >;
reg = <0x1380 0x80>;
@@ -205,17 +203,31 @@
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <0>;
reg = <0x1700 0x20>;
interrupts = <9 0x8>;
interrupt-parent = < &ipic >;
+ fsl,preserve-clocking;
+
+ hwmon at 4a {
+ compatible = "adi,ad7414";
+ reg = <0x4a>;
+ };
+
+ eeprom at 50 {
+ compatible = "at,24c32";
+ reg = <0x50>;
+ };
+
+ rtc at 68 {
+ compatible = "stm,m41t62";
+ reg = <0x68>;
+ };
};
i2c at 1720 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <1>;
reg = <0x1720 0x20>;
interrupts = <10 0x8>;
interrupt-parent = < &ipic >;
@@ -225,7 +237,6 @@
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <2>;
reg = <0x1740 0x20>;
interrupts = <11 0x8>;
interrupt-parent = < &ipic >;
@@ -244,7 +255,7 @@
};
display at 2100 {
- compatible = "fsl,mpc5121-diu", "fsl-diu";
+ compatible = "fsl,mpc5121-diu", "fsl,diu";
reg = <0x2100 0x100>;
interrupts = <64 0x8>;
interrupt-parent = < &ipic >;
@@ -277,7 +288,7 @@
// USB1 using external ULPI PHY
//usb at 3000 {
- // compatible = "fsl,mpc5121-usb2-dr", "fsl-usb2-dr";
+ // compatible = "fsl,mpc5121-usb2-dr";
// reg = <0x3000 0x1000>;
// #address-cells = <1>;
// #size-cells = <0>;
@@ -285,12 +296,11 @@
// interrupts = <43 0x8>;
// dr_mode = "otg";
// phy_type = "ulpi";
- // port1;
//};
// USB0 using internal UTMI PHY
usb at 4000 {
- compatible = "fsl,mpc5121-usb2-dr", "fsl-usb2-dr";
+ compatible = "fsl,mpc5121-usb2-dr";
reg = <0x4000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
@@ -298,7 +308,8 @@
interrupts = <44 0x8>;
dr_mode = "otg";
phy_type = "utmi_wide";
- port0;
+ fsl,invert-drvvbus;
+ fsl,invert-pwr-fault;
};
// IO control
@@ -365,7 +376,7 @@
};
dma at 14000 {
- compatible = "fsl,mpc5121-dma2";
+ compatible = "fsl,mpc5121-dma";
reg = <0x14000 0x1800>;
interrupts = <65 0x8>;
interrupt-parent = < &ipic >;
--
1.6.3.3
More information about the Linuxppc-dev
mailing list