[PATCH 05/10] 8xx: Fixup DAR from buggy dcbX instructions.
Joakim Tjernlund
Joakim.Tjernlund at transmode.se
Sat Nov 14 21:42:23 EST 2009
This is an assembler version to fixup DAR not being set
by dcbX, icbi instructions. There are two versions, one
uses selfmodifing code, the other uses a
jump table but is much bigger(default).
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund at transmode.se>
---
arch/powerpc/kernel/head_8xx.S | 147 ++++++++++++++++++++++++++++++++++++++-
1 files changed, 143 insertions(+), 4 deletions(-)
diff --git a/arch/powerpc/kernel/head_8xx.S b/arch/powerpc/kernel/head_8xx.S
index 0c2bf00..a4a94ad 100644
--- a/arch/powerpc/kernel/head_8xx.S
+++ b/arch/powerpc/kernel/head_8xx.S
@@ -494,11 +494,16 @@ DataTLBError:
mfspr r10, SPRN_DAR
cmpwi cr0, r10, 0x00f0
- beq- 2f /* must be a buggy dcbX, icbi insn. */
-
+ beq- FixupDAR /* must be a buggy dcbX, icbi insn. */
+DARFixed:/* Return from dcbx instruction bug workaround, r10 holds value of DAR */
mfspr r11, SPRN_DSISR
- andis. r11, r11, 0x4800 /* !translation or protection */
- bne 2f /* branch if either is set */
+ /* As the DAR fixup may clear store we may have all 3 states zero.
+ * Make sure only 0x0200(store) falls down into DIRTY handling
+ */
+ andis. r11, r11, 0x4a00 /* !translation, protection or store */
+ srwi r11, r11, 16
+ cmpwi cr0, r11, 0x0200 /* just store ? */
+ bne 2f
/* Only Change bit left now, do it here as it is faster
* than trapping to the C fault handler.
*/
@@ -604,6 +609,140 @@ DataTLBError:
. = 0x2000
+/* This is the procedure to calculate the data EA for buggy dcbx,dcbi instructions
+ * by decoding the registers used by the dcbx instruction and adding them.
+ * DAR is set to the calculated address and r10 also holds the EA on exit.
+ */
+ /* define if you don't want to use self modifying code */
+#define NO_SELF_MODIFYING_CODE
+FixupDAR:/* Entry point for dcbx workaround. */
+ /* fetch instruction from memory. */
+ mfspr r10, SPRN_SRR0
+ DO_8xx_CPU6(0x3780, r3)
+ mtspr SPRN_MD_EPN, r10
+ mfspr r11, SPRN_M_TWB /* Get level 1 table entry address */
+ cmplwi cr0, r11, 0x0800
+ blt- 3f /* Branch if user space */
+ lis r11, (swapper_pg_dir-PAGE_OFFSET)@h
+ ori r11, r11, (swapper_pg_dir-PAGE_OFFSET)@l
+ rlwimi r11, r10, 22, 0xffc
+3: lwz r11, 0(r11) /* Get the level 1 entry */
+ DO_8xx_CPU6(0x3b80, r3)
+ mtspr SPRN_MD_TWC, r11 /* Load pte table base address */
+ mfspr r11, SPRN_MD_TWC /* ....and get the pte address */
+ lwz r11, 0(r11) /* Get the pte */
+ /* concat physical page address(r11) and page offset(r10) */
+ rlwimi r11, r10, 0, 20, 31
+ lwz r11,0(r11)
+/* Check if it really is a dcbx instruction. */
+/* dcbt and dcbtst does not generate DTLB Misses/Errors,
+ * no need to include them here */
+ srwi r10, r11, 26 /* check if major OP code is 31 */
+ cmpwi cr0, r10, 31
+ bne- 141f
+ rlwinm r10, r11, 0, 21, 30
+ cmpwi cr0, r10, 2028 /* Is dcbz? */
+ beq+ 142f
+ cmpwi cr0, r10, 940 /* Is dcbi? */
+ beq+ 142f
+ cmpwi cr0, r10, 108 /* Is dcbst? */
+ beq+ 144f /* Fix up store bit! */
+ cmpwi cr0, r10, 172 /* Is dcbf? */
+ beq+ 142f
+ cmpwi cr0, r10, 1964 /* Is icbi? */
+ beq+ 142f
+141: mfspr r10, SPRN_DAR /* r10 must hold DAR at exit */
+ b DARFixed /* Nope, go back to normal TLB processing */
+
+144: mfspr r10, SPRN_DSISR
+ rlwinm r10, r10,0,7,5 /* Clear store bit for buggy dcbst insn */
+ mtspr SPRN_DSISR, r10
+142: /* continue, it was a dcbx, dcbi instruction. */
+#ifdef CONFIG_8xx_CPU6
+ lwz r3, 8(r0) /* restore r3 from memory */
+#endif
+#ifndef NO_SELF_MODIFYING_CODE
+ andis. r10,r11,0x1f /* test if reg RA is r0 */
+ li r10,modified_instr at l
+ dcbtst r0,r10 /* touch for store */
+ rlwinm r11,r11,0,0,20 /* Zero lower 10 bits */
+ oris r11,r11,640 /* Transform instr. to a "add r10,RA,RB" */
+ ori r11,r11,532
+ stw r11,0(r10) /* store add/and instruction */
+ dcbf 0,r10 /* flush new instr. to memory. */
+ icbi 0,r10 /* invalidate instr. cache line */
+ lwz r11, 4(r0) /* restore r11 from memory */
+ mfspr r10, SPRN_M_TW /* restore r10 from M_TW */
+ isync /* Wait until new instr is loaded from memory */
+modified_instr:
+ .space 4 /* this is where the add/and instr. is stored */
+ bne+ 143f
+ subf r10,r0,r10 /* r10=r10-r0, only if reg RA is r0 */
+143: mtdar r10 /* store faulting EA in DAR */
+ b DARFixed /* Go back to normal TLB handling */
+#else
+ mfctr r10
+ mtdar r10 /* save ctr reg in DAR */
+ rlwinm r10, r11, 24, 24, 28 /* offset into jump table for reg RB */
+ addi r10, r10, 150f at l /* add start of table */
+ mtctr r10 /* load ctr with jump address */
+ xor r10, r10, r10 /* sum starts at zero */
+ bctr /* jump into table */
+150:
+ add r10, r10, r0 ;b 151f
+ add r10, r10, r1 ;b 151f
+ add r10, r10, r2 ;b 151f
+ add r10, r10, r3 ;b 151f
+ add r10, r10, r4 ;b 151f
+ add r10, r10, r5 ;b 151f
+ add r10, r10, r6 ;b 151f
+ add r10, r10, r7 ;b 151f
+ add r10, r10, r8 ;b 151f
+ add r10, r10, r9 ;b 151f
+ mtctr r11 ;b 154f /* r10 needs special handling */
+ mtctr r11 ;b 153f /* r11 needs special handling */
+ add r10, r10, r12 ;b 151f
+ add r10, r10, r13 ;b 151f
+ add r10, r10, r14 ;b 151f
+ add r10, r10, r15 ;b 151f
+ add r10, r10, r16 ;b 151f
+ add r10, r10, r17 ;b 151f
+ add r10, r10, r18 ;b 151f
+ add r10, r10, r19 ;b 151f
+ add r10, r10, r20 ;b 151f
+ add r10, r10, r21 ;b 151f
+ add r10, r10, r22 ;b 151f
+ add r10, r10, r23 ;b 151f
+ add r10, r10, r24 ;b 151f
+ add r10, r10, r25 ;b 151f
+ add r10, r10, r26 ;b 151f
+ add r10, r10, r27 ;b 151f
+ add r10, r10, r28 ;b 151f
+ add r10, r10, r29 ;b 151f
+ add r10, r10, r30 ;b 151f
+ add r10, r10, r31
+151:
+ rlwinm. r11,r11,19,24,28 /* offset into jump table for reg RA */
+ beq 152f /* if reg RA is zero, don't add it */
+ addi r11, r11, 150b at l /* add start of table */
+ mtctr r11 /* load ctr with jump address */
+ rlwinm r11,r11,0,16,10 /* make sure we don't execute this more than once */
+ bctr /* jump into table */
+152:
+ mfdar r11
+ mtctr r11 /* restore ctr reg from DAR */
+ mtdar r10 /* save fault EA to DAR */
+ b DARFixed /* Go back to normal TLB handling */
+
+ /* special handling for r10,r11 since these are modified already */
+153: lwz r11, 4(r0) /* load r11 from memory */
+ b 155f
+154: mfspr r11, SPRN_M_TW /* load r10 from M_TW */
+155: add r10, r10, r11 /* add it */
+ mfctr r11 /* restore r11 */
+ b 151b
+#endif
+
.globl giveup_fpu
giveup_fpu:
blr
--
1.6.4.4
More information about the Linuxppc-dev
mailing list