[PATCH v4 3/3] powerpc/virtex: Add Xilinx ML510 reference designsupport

[Stephen Neuendorffer]

> -----Original Message-----
> From: linuxppc-dev-bounces+stephen.neuendorffer=xilinx.com at ozlabs.org
[mailto:linuxppc-dev-
> bounces+stephen.neuendorffer=xilinx.com at ozlabs.org] On Behalf Of Grant
Likely
> Sent: Thursday, May 21, 2009 9:25 AM
> To: linuxppc-dev at ozlabs.org; Roderick Colenbrander
> Subject: [PATCH v4 3/3] powerpc/virtex: Add Xilinx ML510 reference
designsupport
> 
> From: Roderick Colenbrander <thunderbird2k at gmail.com>
> 
> Signed-off-by: Roderick Colenbrander <thunderbird2k at gmail.com>
> Signed-off-by: Grant Likely <grant.likely at secretlab.ca>
> ---
> 
>  arch/powerpc/platforms/44x/Kconfig        |   10 +++++++++-
>  arch/powerpc/platforms/44x/Makefile       |    1 +
>  arch/powerpc/platforms/44x/virtex_ml510.c |   29
+++++++++++++++++++++++++++++
>  arch/powerpc/sysdev/xilinx_intc.c         |    5 +++++
>  4 files changed, 44 insertions(+), 1 deletions(-)
>  create mode 100644 arch/powerpc/platforms/44x/virtex_ml510.c
> 
> 
> diff --git a/arch/powerpc/platforms/44x/Kconfig
b/arch/powerpc/platforms/44x/Kconfig
> index 0d83a6a..af1c51d 100644
> --- a/arch/powerpc/platforms/44x/Kconfig
> +++ b/arch/powerpc/platforms/44x/Kconfig
> @@ -156,7 +156,7 @@ config YOSEMITE
>  #	  This option enables support for the IBM PPC440GX evaluation
board.
> 
>  config XILINX_VIRTEX440_GENERIC_BOARD
> -	bool "Generic Xilinx Virtex 440 board"
> +	bool "Xilinx Virtex 5 support"

'Virtex 5' is a little ambiguous..  I'd suggest keeping the old wording,
or saying 'Virtex 5 FXT support'.  Even then it's somewhat ambiguous,
since you could conceivably run linux on microblaze on V5FXT and use the
powerpc for something else..

>  	depends on 44x
>  	default n
>  	select XILINX_VIRTEX_5_FXT
> @@ -171,6 +171,14 @@ config XILINX_VIRTEX440_GENERIC_BOARD
>  	  Most Virtex 5 designs should use this unless it needs to do
some
>  	  special configuration at board probe time.
> 
> +config XILINX_ML510
> +	bool "Xilinx ML510 board support"
> +	depends on XILINX_VIRTEX440_GENERIC_BOARD
> +	select PPC_PCI_CHOICE
> +	select XILINX_PCI if PCI
> +	select PPC_INDIRECT_PCI if PCI
> +	select PPC_I8259 if PCI
> +
>  config PPC44x_SIMPLE
>  	bool "Simple PowerPC 44x board support"
>  	depends on 44x
> diff --git a/arch/powerpc/platforms/44x/Makefile
b/arch/powerpc/platforms/44x/Makefile
> index 01f51da..ee6185a 100644
> --- a/arch/powerpc/platforms/44x/Makefile
> +++ b/arch/powerpc/platforms/44x/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_EBONY)	+= ebony.o
>  obj-$(CONFIG_SAM440EP) 	+= sam440ep.o
>  obj-$(CONFIG_WARP)	+= warp.o
>  obj-$(CONFIG_XILINX_VIRTEX_5_FXT) += virtex.o
> +obj-$(CONFIG_XILINX_ML510) += virtex_ml510.o
> diff --git a/arch/powerpc/platforms/44x/virtex_ml510.c
b/arch/powerpc/platforms/44x/virtex_ml510.c
> new file mode 100644
> index 0000000..ba4a6e3
> --- /dev/null
> +++ b/arch/powerpc/platforms/44x/virtex_ml510.c
> @@ -0,0 +1,29 @@
> +#include <asm/i8259.h>
> +#include <linux/pci.h>
> +#include "44x.h"
> +
> +/**
> + * ml510_ail_quirk

Tpyo, but is the comment even necessary if it doesn't say anything
useful?

> + */
> +static void __devinit ml510_ali_quirk(struct pci_dev *dev)
> +{
> +	/* Enable the IDE controller */
> +	pci_write_config_byte(dev, 0x58, 0x4c);
> +	/* Assign irq 14 to the primary ide channel */
> +	pci_write_config_byte(dev, 0x44, 0x0d);
> +	/* Assign irq 15 to the secondary ide channel */
> +	pci_write_config_byte(dev, 0x75, 0x0f);
> +	/* Set the ide controller in native mode */
> +	pci_write_config_byte(dev, 0x09, 0xff);
> +
> +	/* INTB = disabled, INTA = disabled */
> +	pci_write_config_byte(dev, 0x48, 0x00);
> +	/* INTD = disabled, INTC = disabled */
> +	pci_write_config_byte(dev, 0x4a, 0x00);
> +	/* Audio = INT7, Modem = disabled. */
> +	pci_write_config_byte(dev, 0x4b, 0x60);
> +	/* USB = INT7 */
> +	pci_write_config_byte(dev, 0x74, 0x06);
> +}
> +DECLARE_PCI_FIXUP_EARLY(0x10b9, 0x1533, ml510_ali_quirk);
> +
> diff --git a/arch/powerpc/sysdev/xilinx_intc.c
b/arch/powerpc/sysdev/xilinx_intc.c
> index 90b5772..3ee1fd3 100644
> --- a/arch/powerpc/sysdev/xilinx_intc.c
> +++ b/arch/powerpc/sysdev/xilinx_intc.c
> @@ -257,6 +257,11 @@ static void __init
xilinx_i8259_setup_cascade(void)
>  	i8259_init(cascade_node, 0);
>  	set_irq_chained_handler(cascade_irq, xilinx_i8259_cascade);
> 
> +	/* Program irq 7 (usb/audio), 14/15 (ide) to level sensitive */
> +	/* This looks like a dirty hack to me --gcl */
> +	outb(0xc0, 0x4d0);
> +	outb(0xc0, 0x4d1);
> +

Yeow... I agree about the dirty hack part...  shouldn't this be in the
device tree somewhere, or in the ali driver?

I'm curious if this works on ml410 as well..  (Yes, I know, does this
really matter much?  But there are still a bunch of them floating around
in universities.)  It may be nice to factor this out so ml410/ppc405 and
microblaze can get it as well.

Steve

>   out:
>  	of_node_put(cascade_node);
>  }
> 
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev


This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.