sata device failed to IDENTIFY...

[Tirumala Reddy Marri]

What PCI Sata card  is this ? Is you device tree entrees are correct for
PCI ?  Especially the interrupt numbers etc ?  Also check your ioremap()
function in the SATA driver. Make sure that data type of physical
address in the driver using is "unsigned long long" instead of "unsigned
long"



-----Original Message-----
From: linuxppc-dev-bounces+tmarri=amcc.com at ozlabs.org
[mailto:linuxppc-dev-bounces+tmarri=amcc.com at ozlabs.org] On Behalf Of
rizwan ahmad
Sent: Thursday, March 26, 2009 6:57 AM
To: linuxppc-dev at ozlabs.org
Subject: Re: sata device failed to IDENTIFY...




output of lspci -vv

-bash-3.2# lspci -vv
00:0c.0 Class 0c03: Unknown device 1106:3038 (rev 62)
        Subsystem: Unknown device 1106:3038
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Ste-        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
<TAbor-        Latency: 128
        Interrupt: pin A routed to IRQ 25
        Region 4: I/O ports at ffe0 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3)                Status: D0 PME-Enable- DSel=0
DScale=0
PME-

00:0c.1 Class 0c03: Unknown device 1106:3038 (rev 62)
        Subsystem: Unknown device 1106:3038
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Ste-        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
<TAbor-        Latency: 128
        Interrupt: pin B routed to IRQ 25
        Region 4: I/O ports at ffc0 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3)                Status: D0 PME-Enable- DSel=0
DScale=0
PME-

00:0c.2 Class 0c03: Unknown device 1106:3104 (rev 65) (prog-if 20)
        Subsystem: Unknown device 1106:3104
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Ste-        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
<TAbor-        Latency: 128
        Interrupt: pin C routed to IRQ 25
        Region 0: Memory at afffff00 (32-bit, non-prefetchable)
[size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3)                Status: D0 PME-Enable- DSel=0
DScale=0
PME-

00:0c.3 Class 0104: Unknown device 1106:3249 (rev 50)
        Subsystem: Unknown device 1106:3249
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
Ste-        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort-
<TAbor-        Latency: 128
        Interrupt: pin A routed to IRQ 25
        Region 0: I/O ports at ffb0 [size=16]
        Region 1: I/O ports at ffa0 [size=16]
        Region 2: I/O ports at ff90 [size=16]
        Region 3: I/O ports at ff80 [size=16]
        Region 4: I/O ports at ff60 [size=32]
        Region 5: I/O ports at fe00 [size=256]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [e0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3ho)                Status: D0 PME-Enable- DSel=0
DScale=0
PME-

-bash-3.2#



-- 
View this message in context:
http://www.nabble.com/sata-device-failed-to-IDENTIFY...-tp22655709p22722
574.html
Sent from the linuxppc-dev mailing list archive at Nabble.com.

_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev at ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-dev