[PATCH v3 3/4] powerpc: NAND: FSL UPM: document new bindings

Wolfgang Grandegger wg at grandegger.com
Fri Mar 27 02:33:54 EST 2009


Grant Likely wrote:
> On Thu, Mar 26, 2009 at 1:42 AM, Wolfgang Grandegger <wg at grandegger.com> wrote:
>> Grant Likely wrote:
>>> On Wed, Mar 25, 2009 at 2:48 PM, Wolfgang Grandegger <wg at grandegger.com> wrote:
>>>> Grant Likely wrote:
>>>>> For the chip offset, it's not clear what the meaning is.  First, does
>>>>> the UPM controller support access of multiple chips simultaneously?
>>>> The offset drives the corresponding address lines, which are used to
>>>> select the chip. That's how it's done on the TQM8548 board. In
>>>> principle, the chips could also be selected through dedicated GPIO pins.
>>>> Well, I'm not a hardware guy.
>>> Heh.  I mean elaborate in the binding documentation.  :-)
>>>
>>>>> If so, then can you elaborate in the description on how board design
>>>>> translates to a chip-offset value.  If it cannot, then it might be
>>>>> better to have multiple tuples in the 'reg' property for each discrete
>>>>> chip.  Multiple reg tuples would also remove the need for the
>>>>> num-chips property.
>>>> The node still describes one device mapping all relevant control
>>>> registers. How about using fsl,upm-chip-offsets = <0x200 0x400>. It
>>>> would be more generic and makes num-chips obsolete as well. And the
>>>> property would be reserved for that way of implementing the chip select
>>>> in hardware.
>>> It really sounds like this binding is describing multiple NAND chips
>>> mapped to different base addresses (and looking at the fsm_upm.c
>>> driver appears to confirm it).  So, does this work?  reg = <3 0x200 4
>>>  3 0x400 4>;
>> The chip-offset, and not the address, needs to be added to the MAR
>> register as well before running the pattern:
>>
>>        mar = cmd << (32 - fun->upm.width);
>>
>>        if (fun->chip_offset && fun->chip_number > 0)
>>
>>                mar |= fun->chip_number * fun->chip_offset;
>>
>>        fsl_upm_run_pattern(&fun->upm, chip->IO_ADDR_R, mar);
>>
>>
>>> It is true that other methods could be used for implementing the chip
>>> select, but that is *not* what the proposed binding describes.  This
>>> proposed binding describes NAND chips selected by address lines
>>> (particular addresses), and in this case I think using reg is the
>>> natural description.
>> OK, the chips are selected by accessing a defined address range. Will
>> prepare a patch using the reg property.
> 
> Hold on a sec.  I'm debating from my experience with device tree

I already started ;-).

> bindings, but I'm fairly ignorant about the implementation of NAND on
> UPM.  It *looks* to me like reg is sufficient, but if I'm wrong then
> tell me so and why.  Your comment above about fsl_upm_run_pattern()
> makes me doubt my position.

It's not sufficient to just map the related space and access it, at least.

> Does using the reg property give the driver enough information to
> reliably program the MAR for NAND connections that use the address
> line chip select scheme?  Related to that, should the binding include

In principle yes:

  if (i > 0)
      offset[i] = resource[i].start - resource[0].start;

> a property that explicitly states that an address line chip select
> scheme is being used?

That's why I'm still in favor of:

  fsl,upm-multi-chip-offsets = <0x200 0x400>

That would state that the address line chip select scheme is used with
the specified offsets. It also allows for a more elegant solution
(code-wise).

Wolfgang.




More information about the Linuxppc-dev mailing list