DTS file PCI / i8259 for Xilinx ML510

[Roderick Colenbrander]

-------- Original-Nachricht --------
> Datum: Mon, 16 Mar 2009 09:18:54 +0100
> Von: "Roderick Colenbrander" <thunderbird2k at gmx.net>
> An: "Gerhard Pircher" <gerhard_pircher at gmx.net>, linuxppc-dev at ozlabs.org
> Betreff: Re: DTS file PCI / i8259 for Xilinx ML510

> 
> -------- Original-Nachricht --------
> > Datum: Sun, 15 Mar 2009 11:43:13 +0100
> > Von: "Gerhard Pircher" <gerhard_pircher at gmx.net>
> > An: "Roderick Colenbrander" <thunderbird2k at gmx.net>,
> linuxppc-dev at ozlabs.org
> > Betreff: Re: DTS file PCI / i8259 for Xilinx ML510
> 
> > 
> > -------- Original-Nachricht --------
> > > Datum: Sun, 15 Mar 2009 09:38:26 +0100
> > > Von: "Roderick Colenbrander" <thunderbird2k at gmx.net>
> > > An: "Gerhard Pircher" <gerhard_pircher at gmx.net>,
> linuxppc-dev at ozlabs.org
> > > Betreff: Re: DTS file PCI / i8259 for Xilinx ML510
> > 
> > > > > At some point in the file they create some (dummy?) pcie section
> in
> > > > > which they define a uli1575, an isa bus and attached to that isa
> bus
> > > > > a i8259. Is this the correct way of doing things? The i8259 driver
> > > > > seems to use io ports 0x20-21/0xa0-0xa1/0x4d0-0x4d1 those are also
> > > > > defined below but how are those mapped to the south bridge? I have
> > > > > seen some code in kernel/isa-bridge, is that code indeed
> responsible
> > > > > for setting up these ports?
> > > > Yes, the pcie node is the PCI host bridge node and the uli1571 node
> > > > acts as PCI2ISA bridge node. AFAIK their ranges properties are
> parsed
> > > > by pci_process_bridge_OF_ranges().
> > > > IIRC the code in kernel/isa-bridge is used for 64bit PPC machines
> only
> > > > for now. The I/O addresses for the i8259 PIC are currently hardcoded
> > > > and setup (request_resource()) in sysdev/i8259.c.
> > > 
> > > I got the i8259 south bridge working now after adding an io_base_virt
> > > offset to all inb/outb lines in sysdev/i8259.c. Would it be worth all
> > > the troubles to add ppc32 support to isa-bridge.c? The whole point of
> > > the code is basically to remap the io memory to low addresses for
> these
> > > 64-bit ppc systems (mainly freescale boards with a i8259 and pseries
> > > systems with a i8259).
> > pci_process_bridge_OF_ranges() should "ioremap" io_base_virt for you,
> > if your board has only one PCI I/O space. It also sets isa_io_base to
> > io_base_virt on PPC32, but expects that the ISA I/O space is mapped to
> > PCI I/O address 0x0. Isn't that the case for your board?
> > 
> > > As far as I have seen it is only needed for i8259 interrupt
> controllers.
> > > Personally I think it would be better to pass a io base offset to
> > > i8259_setup or so. Or perhaps do some dts file parsing in i8259.c.
> > > I'm not sure what the proper layout would be for this in the dts file
> > > though.
> > I think adding an io base offset parameter to i8259_setup isn't the
> > right way to do it. I would expect other problems too, if ISA I/O space
> > isn't mapped 1:1 to PCI I/O space on a PPC32 system. Maybe a more
> > experienced kernel developer can comment on this?
> 
> I'm now back behind my ML510 board and have been doing some tests. As I
> mentioned before I was doing inb(isa_io_base + port) / outb(val, isa_io_base
> + port) which worked fine. As far as I see it the problem is the definition
> of inb/outb on ppc32 they don't take isa_io_base into account. They are:
> __do_in_asm(_rec_inb, "lbzx")
> __do_out_asm(_rec_outb, "stbx")
> #define __do_outb(val, port)    _rec_outb(val, port)
> #define __do_inb(port)          _rec_inb(port)
> 
> While on 64-bit ppc they are:
> #define __do_outb(val, port)    writeb(val,(PCI_IO_ADDR)_IO_BASE+port);
> #define __do_inb(port)          readb((PCI_IO_ADDR)_IO_BASE + port);
> 
> (On ppc32 _IO_BASE is isa_io_base but on 64-bit it is set to pci_io_base)
> 
> Am I correct that inb/outb are broken on ppc32? If so what is the right
> way to fix them?
> 
> Regards,
> Roderick

I just talked about this on IRC with Benjamin Herrenschmidt and I misunderstood the inb/outb command. the commands are using _IO_PORTS and I must be doing something wrong.

Roderick
-- 
Nur bis 16.03.! DSL-Komplettanschluss inkl. WLAN-Modem für nur 
17,95 ¿/mtl. + 1 Monat gratis!* http://dsl.gmx.de/?ac=OM.AD.PD003K11308T4569a