help:About USB_EHCI_ROOT_HUB_TT in MPC8347 USB development
Cris Gong
Cris.Gong at accton.com.cn
Mon Mar 9 17:29:58 EST 2009
Greetings,
I have an mpc8347 board here.The linux kernel version is 2.6.19.2.
MPC8347 MPH0 is connectted to a FS/LS PHY(Philips ISP1105),I insert a
USB 2.0 storage disk.
I add initial usb_platform_data in
linux_2.6.19.2/arch/ppc/syslib/mpc83xx_devices.c
static struct fsl_usb2_platform_data mpc83xx_usb_platform_data = {
.operating_mode = FSL_USB2_MPH_HOST,
.phy_mode = FSL_USB2_PHY_SERIAL,
.port_enables = FSL_USB2_PORT0_ENABLED,
};
In kernel config,I have set CONFIG_USB_EHCI_ROOT_HUB_TT to y(get rid of
EXPERIMENTAL)
Why does it report error -32?(the Macro is EPIPE)
The following is capture file.
## Booting image at 01000000 ...
Loading image:
Image version:
Created: 2009-03-06 7:52:17 UTC
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
Loading Ramdisk to 03e8b000, end 04000000 ... OK
Linux version 2.6.19.2-0.1 (cris.gong at atan-cat.accton.com.cn) (gcc version
4.0.0 (DENX ELDK 4.1 4.0.0)) #1 PREEMPT Fri Mar 6 15:48:37 CST 2009
Zone PFN ranges:
DMA 0 -> 125952
Normal 125952 -> 125952
early_node_map[1] active PFN ranges
0: 0 -> 125952
Built 1 zonelists. Total pages: 124968
Kernel command line: root=/dev/ram rw console=ttyS0,115200 mem=492M
dbg_start=0x1fc00914 dbg_size=524288
IPIC (128 IRQ sources, 8 External IRQs) at fe000700
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 494464k available (2036k kernel code, 1192k data, 144k init, 0k
highmem)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (bad gzip magic numbers); looks
like an initrd
Freeing initrd memory: 1492k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler cfq registered (default)
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.2, 00:08:07:00:00:39
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.2, 85:e1:89:82:72:6f
eth1: Running with NAPI enabled
eth1: 256/256 RX/TX BD ring size
Common Flash mtd init ...
physmap platform flash device: 04000000 at fc000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 8 MTD partitions on "physmap-flash.0":
0x03f00000-0x03f80000 : "loader"
0x03c00000-0x03c20000 : "partitiontable"
0x03c20000-0x03c40000 : "environment"
0x03c40000-0x03c60000 : "filemapping"
0x03c60000-0x03c80000 : "hwinfo"
0x00c00000-0x01000000 : "userdata"
0x01000000-0x02000000 : "runtime0"
0x02000000-0x03000000 : "runtime1"
fsl-ehci fsl-ehci.1: No platform data for fsl-ehci.1.
fsl-ehci fsl-ehci.2: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.2: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.2: irq 39, io base 0xe0022000
fsl-ehci fsl-ehci.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.19.2-0.1 ehci_hcd
usb usb1: SerialNumber: fsl-ehci.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using fsl-ehci and address 2
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 3
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 4
usb 1-1: device not accepting address 4, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 5
usb 1-1: device not accepting address 5, error -32
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 1492KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 144k init
Running rc.accton.init ...
Please press Enter to activate this console.
root:~> echo 8 > /proc/sys/kernel/printk
root:~> hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
fsl-ehci fsl-ehci.2: GetStatus port 1 status cc001002 POWER sig=se0 CSC
hub 1-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
fsl-ehci fsl-ehci.2: GetStatus port 1 status c0001803 POWER sig=j CSC
CONNECT
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
fsl-ehci fsl-ehci.2: port 1 high speed
fsl-ehci fsl-ehci.2: GetStatus port 1 status c0001005 POWER sig=se0 PE
CONNECT
usb 1-1: new full speed USB device using fsl-ehci and address 6
fsl-ehci fsl-ehci.2: port 1 high speed
fsl-ehci fsl-ehci.2: GetStatus port 1 status c0001005 POWER sig=se0 PE
CONNECT
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 7
fsl-ehci fsl-ehci.2: port 1 high speed
fsl-ehci fsl-ehci.2: GetStatus port 1 status c0001005 POWER sig=se0 PE
CONNECT
usb 1-1: device descriptor read/64, error -32
usb 1-1: device descriptor read/64, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 8
usb 1-1: device not accepting address 8, error -32
usb 1-1: new full speed USB device using fsl-ehci and address 9
usb 1-1: device not accepting address 9, error -32
The following is my kernel configure file.
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.19.2-0.1
# Wed Mar 4 13:35:26 2009
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not set
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
CONFIG_KALLSYMS_EXTRA_PASS=y
# CONFIG_HOTPLUG is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
# CONFIG_VM_EVENT_COUNTERS is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
#
# Block layer
#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
#
# Processor
#
CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_8xx is not set
# CONFIG_E200 is not set
# CONFIG_E500 is not set
CONFIG_PPC_FPU=y
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_PPC_GEN550=y
# CONFIG_ES4626H is not set
CONFIG_PPC_STD_MMU=y
#
# Platform options
#
# CONFIG_PPC_PREP is not set
# CONFIG_APUS is not set
# CONFIG_KATANA is not set
# CONFIG_WILLOW is not set
# CONFIG_CPCI690 is not set
# CONFIG_POWERPMC250 is not set
# CONFIG_CHESTNUT is not set
# CONFIG_SPRUCE is not set
# CONFIG_HDPU is not set
# CONFIG_EV64260 is not set
# CONFIG_LOPEC is not set
# CONFIG_MVME5100 is not set
# CONFIG_PPLUS is not set
# CONFIG_PRPMC750 is not set
# CONFIG_PRPMC800 is not set
# CONFIG_SANDPOINT is not set
# CONFIG_RADSTONE_PPC7D is not set
# CONFIG_PAL4 is not set
# CONFIG_GEMINI is not set
# CONFIG_EST8260 is not set
# CONFIG_SBC82xx is not set
# CONFIG_SBS8260 is not set
# CONFIG_RPX8260 is not set
# CONFIG_TQM8260 is not set
# CONFIG_PM82X is not set
# CONFIG_ADS8272_PLATFORM is not set
CONFIG_ASF4528B=y
# CONFIG_PQ2FADS is not set
# CONFIG_LITE5200 is not set
# CONFIG_EV64360 is not set
# CONFIG_TQM834x is not set
# CONFIG_TQM8272 is not set
CONFIG_MPC834x_SYS=y
CONFIG_83xx=y
CONFIG_MPC834x=y
CONFIG_PPC_83xx=y
# CONFIG_SMP is not set
# CONFIG_HIGHMEM is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_GENERIC_ISA_DMA=y
# CONFIG_PPC_I8259 is not set
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_MPC83xx_PCI2 is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
#
# PCI Express support
#
#
# Advanced setup
#
CONFIG_ADVANCED_OPTIONS=y
CONFIG_HIGHMEM_START=0xfe000000
# CONFIG_LOWMEM_SIZE_BOOL is not set
CONFIG_LOWMEM_SIZE=0x30000000
# CONFIG_KERNEL_START_BOOL is not set
CONFIG_KERNEL_START=0xc0000000
# CONFIG_TASK_SIZE_BOOL is not set
CONFIG_TASK_SIZE=0x80000000
# CONFIG_BOOT_LOAD_BOOL is not set
CONFIG_BOOT_LOAD=0x00800000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=y
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
# CONFIG_DEFAULT_BIC is not set
CONFIG_DEFAULT_CUBIC=y
# CONFIG_DEFAULT_HTCP is not set
# CONFIG_DEFAULT_VEGAS is not set
# CONFIG_DEFAULT_WESTWOOD is not set
# CONFIG_DEFAULT_RENO is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PHYSMAP_START=0xFE000000
CONFIG_MTD_PHYSMAP_LEN=0x02000000
CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_ECN430_FB2_FLASH is not set
CONFIG_MTD_ASF4528B_FLASH=y
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
#
# NAND Flash Device Drivers
#
# CONFIG_MTD_NAND is not set
#
# OneNAND Flash Device Drivers
#
# CONFIG_MTD_ONENAND is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
# CONFIG_SGI_IOC4 is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Macintosh device drivers
#
# CONFIG_WINDFARM is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
CONFIG_PHYLIB=y
#
# MII PHY device drivers
#
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_FIXED_PHY is not set
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
CONFIG_GIANFAR=y
CONFIG_GFAR_NAPI=y
# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
# CONFIG_INPUT is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
# CONFIG_VT is not set
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_MPC=y
# CONFIG_I2C_MPC8260 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_M41T00 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
# CONFIG_HWMON_VID is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Input Devices
#
# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
#
#
# USB Imaging devices
#
# CONFIG_USB_MICROTEK is not set
#
# USB Network Adapters
#
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# LED devices
#
# CONFIG_NEW_LEDS is not set
#
# LED drivers
#
#
# LED Triggers
#
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# Real Time Clock
#
#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set
#
# DMA Clients
#
#
# DMA Devices
#
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_HFSPLUS_FS is not set
# CONFIG_JFFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
CONFIG_JFFS2_RUBIN=y
# CONFIG_JFFS2_CMODE_NONE is not set
CONFIG_JFFS2_CMODE_PRIORITY=y
# CONFIG_JFFS2_CMODE_SIZE is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=y
CONFIG_NLS_CODEPAGE_775=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_CODEPAGE_852=y
CONFIG_NLS_CODEPAGE_855=y
CONFIG_NLS_CODEPAGE_857=y
CONFIG_NLS_CODEPAGE_860=y
CONFIG_NLS_CODEPAGE_861=y
CONFIG_NLS_CODEPAGE_862=y
CONFIG_NLS_CODEPAGE_863=y
CONFIG_NLS_CODEPAGE_864=y
CONFIG_NLS_CODEPAGE_865=y
CONFIG_NLS_CODEPAGE_866=y
CONFIG_NLS_CODEPAGE_869=y
CONFIG_NLS_CODEPAGE_936=y
CONFIG_NLS_CODEPAGE_950=y
CONFIG_NLS_CODEPAGE_932=y
CONFIG_NLS_CODEPAGE_949=y
CONFIG_NLS_CODEPAGE_874=y
CONFIG_NLS_ISO8859_8=y
CONFIG_NLS_CODEPAGE_1250=y
CONFIG_NLS_CODEPAGE_1251=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=y
CONFIG_NLS_ISO8859_3=y
CONFIG_NLS_ISO8859_4=y
CONFIG_NLS_ISO8859_5=y
CONFIG_NLS_ISO8859_6=y
CONFIG_NLS_ISO8859_7=y
CONFIG_NLS_ISO8859_9=y
CONFIG_NLS_ISO8859_13=y
CONFIG_NLS_ISO8859_14=y
CONFIG_NLS_ISO8859_15=y
CONFIG_NLS_KOI8_R=y
CONFIG_NLS_KOI8_U=y
CONFIG_NLS_UTF8=y
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_KGDB is not set
# CONFIG_XMON is not set
# CONFIG_BDI_SWITCH is not set
# CONFIG_SERIAL_TEXT_DEBUG is not set
# CONFIG_ICE_DEBUG is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
Best Regards!
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20090309/385924c1/attachment.htm>
More information about the Linuxppc-dev
mailing list