[PATCH RFC] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
Anton Vorontsov
avorontsov at ru.mvista.com
Wed Mar 4 06:38:33 EST 2009
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood at freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
---
On Tue, Mar 03, 2009 at 12:39:38PM -0600, Scott Wood wrote:
> Anton Vorontsov wrote:
>> On Tue, Mar 03, 2009 at 11:57:46AM -0600, Scott Wood wrote:
>>> On Tue, Mar 03, 2009 at 07:02:01PM +0300, Anton Vorontsov wrote:
>>>> mdio at 24520 {
>>>> @@ -226,6 +244,8 @@
>>>> interrupt-parent = <&ipic>;
>>>> tbi-handle = <&tbi0>;
>>>> phy-handle = <&phy2>;
>>>> + sleep = <&pmc 0xc0000000>;
>>>> + fsl,magic-packet;
>>>> };
>>> Note that this makes it look to the kernel like enet0 can be put to sleep
>>> without putting the mdio (which is shared with enet1) to sleep. This is
>>> why I moved mdio under the ethernet node on 8313erdb.
>>
>> And that isn't absolutely correct either, since enet1 depends on
>> net0... If enet0's mdio goes into sleep mode before enet1, then
>> enet1 will fail to send power-down command to its PHY...
>
> But the kernel knows that enet1 depends on mdio0. Getting the kernel to
> act on that knowledge isn't the device tree's problem.
Well, that makes sense. I'd like to move mdio nodes in a separate
patch though, since the original patch becomes difficult to review
because of too many changes...
A question though... do we want real addr translation via ranges, or
the dummy "ranges;" are OK?
Here is the RFC. It's tested to work on MPC8377-RDB.
Please review carefully..
Thanks,
arch/powerpc/boot/dts/mpc8315erdb.dts | 84 ++++++++++++++++-------------
arch/powerpc/boot/dts/mpc8349emitx.dts | 73 ++++++++++++++------------
arch/powerpc/boot/dts/mpc8349emitxgp.dts | 44 ++++++++-------
arch/powerpc/boot/dts/mpc834x_mds.dts | 85 ++++++++++++++++--------------
arch/powerpc/boot/dts/mpc8377_mds.dts | 84 ++++++++++++++++-------------
arch/powerpc/boot/dts/mpc8377_rdb.dts | 71 ++++++++++++++-----------
arch/powerpc/boot/dts/mpc8378_mds.dts | 84 ++++++++++++++++-------------
arch/powerpc/boot/dts/mpc8378_rdb.dts | 73 ++++++++++++++-----------
arch/powerpc/boot/dts/mpc8379_mds.dts | 83 ++++++++++++++++-------------
arch/powerpc/boot/dts/mpc8379_rdb.dts | 70 ++++++++++++++-----------
10 files changed, 413 insertions(+), 338 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8315erdb.dts b/arch/powerpc/boot/dts/mpc8315erdb.dts
index 88d691c..ba355b5 100644
--- a/arch/powerpc/boot/dts/mpc8315erdb.dts
+++ b/arch/powerpc/boot/dts/mpc8315erdb.dts
@@ -190,66 +190,74 @@
phy_type = "utmi";
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy0: ethernet-phy at 0 {
- interrupt-parent = <&ipic>;
- interrupts = <20 0x8>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy at 1 {
- interrupt-parent = <&ipic>;
- interrupts = <19 0x8>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = < &phy0 >;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&ipic>;
+ interrupts = <20 0x8>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&ipic>;
+ interrupts = <19 0x8>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = < &phy1 >;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts
index b5eda94..c42413a 100644
--- a/arch/powerpc/boot/dts/mpc8349emitx.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitx.dts
@@ -170,57 +170,52 @@
phy_type = "ulpi";
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- /* Vitesse 8201 */
- phy1c: ethernet-phy at 1c {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1c>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy1c>;
linux,network-index = <0>;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ /* Vitesse 8201 */
+ phy1c: ethernet-phy at 1c {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1c>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
@@ -228,6 +223,18 @@
fixed-link = <1 1 1000 0 0>;
linux,network-index = <1>;
tbi-handle = <&tbi1>;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
index c87a601..c8c6d8e 100644
--- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
@@ -149,37 +149,41 @@
phy_type = "ulpi";
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- /* Vitesse 8201 */
- phy1c: ethernet-phy at 1c {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1c>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy1c>;
linux,network-index = <0>;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ /* Vitesse 8201 */
+ phy1c: ethernet-phy at 1c {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1c>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts
index d9adba0..86039a6 100644
--- a/arch/powerpc/boot/dts/mpc834x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc834x_mds.dts
@@ -167,69 +167,76 @@
phy_type = "ulpi";
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy at 0 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy at 1 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
linux,network-index = <0>;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy0: ethernet-phy at 0 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy at 1 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
linux,network-index = <1>;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
index cebfc50..c1afcbc 100644
--- a/arch/powerpc/boot/dts/mpc8377_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -196,48 +196,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy at 3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -246,14 +213,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy at 3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -262,6 +258,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts
index 32311c8..c3d1fbe 100644
--- a/arch/powerpc/boot/dts/mpc8377_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts
@@ -248,42 +248,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -292,14 +265,36 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -308,6 +303,18 @@
tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
index 155841d..fabdd82 100644
--- a/arch/powerpc/boot/dts/mpc8378_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -235,48 +235,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy at 3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -285,14 +252,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy at 3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -301,6 +297,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts
index 54ad96c..e11ae76 100644
--- a/arch/powerpc/boot/dts/mpc8378_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts
@@ -248,64 +248,73 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
+ tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
fixed-link = <1 1 1000 0 0>;
+ tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts
index 9deb5b2..143aa53 100644
--- a/arch/powerpc/boot/dts/mpc8379_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8379_mds.dts
@@ -233,47 +233,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy at 3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -282,14 +250,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy at 3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -298,6 +295,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts
index 3f4778f..58145d0 100644
--- a/arch/powerpc/boot/dts/mpc8379_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts
@@ -246,41 +246,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio at 24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy at 2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio at 25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy at 11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet at 24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x24000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -289,14 +263,36 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio at 24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy2: ethernet-phy at 2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet at 25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
- compatible = "gianfar";
+ compatible = "gianfar", "simple-bus";
reg = <0x25000 0x1000>;
+ ranges;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -305,6 +301,18 @@
tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio at 25520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x25520 0x20>;
+
+ tbi1: tbi-phy at 11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial at 4500 {
--
1.5.6.5
More information about the Linuxppc-dev
mailing list