[PATCH] Add support for the ESTeem 195E (PPC405EP) SBC
Solomon Peachy
solomon at linux-wlan.com
Fri Jul 24 01:21:45 EST 2009
This patch adds support for the ESTeem 195E Hotfoot SBC.
We've been maintaining this out-of-tree for some time now for
older kernels, but recently I ported it to the new unified powerpc tree
with the intent of pushing it upstream.
The board uses an ancient version of u-boot and a slightly mangled
verison of the oft-abused ppcboot header.
There are several variants of the SBC deployed, single/dual
ethernet/serial, and also 4MB/8MB flash units. In the interest of
having a single kernel image boot on all boards, the cuboot shim detects
the differences and mangles the DTS tree appropriately.
With the exception of the CF interface that was never populated on
production boards, this code/DTS supports all boardpop options.
Signed-off-by: Solomon Peachy <solomon at linux-wlan.com>
diff -Naur linux-2.6.30/arch/powerpc/boot/Makefile linux-2.6.30.hotfoot/arch/powerpc/boot/Makefile
--- linux-2.6.30/arch/powerpc/boot/Makefile 2009-06-09 23:05:27.000000000 -0400
+++ linux-2.6.30.hotfoot/arch/powerpc/boot/Makefile 2009-07-07 12:55:18.000000000 -0400
@@ -39,6 +39,7 @@
$(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
$(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
+$(obj)/cuboot-hotfoot.o: BOOTCFLAGS += -mcpu=405
$(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405
$(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
@@ -67,7 +68,7 @@
cpm-serial.c stdlib.c mpc52xx-psc.c planetcore.c uartlite.c \
fsl-soc.c mpc8xx.c pq2.c
src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c \
- cuboot-ebony.c treeboot-ebony.c prpmc2800.c \
+ cuboot-ebony.c cuboot-hotfoot.c treeboot-ebony.c prpmc2800.c \
ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c \
cuboot-bamboo.c cuboot-mpc7448hpc2.c cuboot-taishan.c \
@@ -190,6 +191,7 @@
# Board ports in arch/powerpc/platform/40x/Kconfig
image-$(CONFIG_EP405) += dtbImage.ep405
+image-$(CONFIG_HOTFOOT) += cuImage.hotfoot
image-$(CONFIG_WALNUT) += treeImage.walnut
image-$(CONFIG_ACADIA) += cuImage.acadia
diff -Naur linux-2.6.30/arch/powerpc/boot/cuboot-hotfoot.c linux-2.6.30.hotfoot/arch/powerpc/boot/cuboot-hotfoot.c
--- linux-2.6.30/arch/powerpc/boot/cuboot-hotfoot.c 1969-12-31 19:00:00.000000000 -0500
+++ linux-2.6.30.hotfoot/arch/powerpc/boot/cuboot-hotfoot.c 2009-07-07 12:55:23.000000000 -0400
@@ -0,0 +1,142 @@
+/*
+ * Old U-boot compatibility for Esteem 195E Hotfoot CPU Board
+ *
+ * Author: Solomon Peachy <solomon at linux-wlan.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "reg.h"
+#include "dcr.h"
+#include "4xx.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_HOTFOOT
+
+#include "ppcboot.h"
+
+static bd_t bd;
+
+#define NUM_REGS 3
+
+static void hotfoot_fixups(void)
+{
+ u32 uart = mfdcr(DCRN_CPC0_UCR) & 0x7f;
+
+ dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
+
+ dt_fixup_cpu_clocks(bd.bi_procfreq, bd.bi_procfreq, 0);
+ dt_fixup_clock("/plb", bd.bi_plb_busfreq);
+ dt_fixup_clock("/plb/opb", bd.bi_opbfreq);
+ dt_fixup_clock("/plb/ebc", bd.bi_pci_busfreq);
+ dt_fixup_clock("/plb/opb/serial at ef600300", bd.bi_procfreq / uart);
+ dt_fixup_clock("/plb/opb/serial at ef600400", bd.bi_procfreq / uart);
+
+ dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+ dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
+
+ /* Is this a single eth/serial board? */
+ if ((bd.bi_enet1addr[0] == 0) &&
+ (bd.bi_enet1addr[1] == 0) &&
+ (bd.bi_enet1addr[2] == 0) &&
+ (bd.bi_enet1addr[3] == 0) &&
+ (bd.bi_enet1addr[4] == 0) &&
+ (bd.bi_enet1addr[5] == 0)) {
+ void *devp;
+
+ printf("Trimming devtree for single eth board\n");
+
+ devp = finddevice("/plb/opb/serial at ef600300");
+ if (!devp)
+ fatal("Can't find node for /plb/opb/serial at ef600300");
+ del_node(devp);
+
+ devp = finddevice("/plb/opb/ethernet at ef600900");
+ if (!devp)
+ fatal("Can't find node for /plb/opb/ethernet at ef600900");
+ del_node(devp);
+ }
+
+ ibm4xx_quiesce_eth((u32 *)0xef600800, (u32 *)0xef600900);
+
+ /* Fix up flash size in fdt for 4M boards. */
+ if (bd.bi_flashsize < 0x800000) {
+ u32 regs[NUM_REGS];
+ void *devp = finddevice("/plb/ebc/nor_flash at 0");
+ if (!devp)
+ fatal("Can't find FDT node for nor_flash!??");
+
+ printf("Fixing devtree for 4M Flash\n");
+
+ /* First fix up the base addresse */
+ getprop(devp, "reg", regs, sizeof(regs));
+ regs[0] = 0;
+ regs[1] = 0xffc00000;
+ regs[2] = 0x00400000;
+ setprop(devp, "reg", regs, sizeof(regs));
+
+ /* Then the offsets */
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 0");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 0");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 1");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 1");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 2");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 2");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 3");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 3");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 4");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 4");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 6");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 6");
+ getprop(devp, "reg", regs, 2*sizeof(u32));
+ regs[0] -= 0x400000;
+ setprop(devp, "reg", regs, 2*sizeof(u32));
+
+ /* Delete the FeatFS node */
+ devp = finddevice("/plb/ebc/nor_flash at 0/partition at 5");
+ if (!devp)
+ fatal("Can't find FDT node for partition at 5");
+ del_node(devp);
+ }
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+ platform_ops.fixups = hotfoot_fixups;
+ platform_ops.exit = ibm40x_dbcr_reset;
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
diff -Naur linux-2.6.30/arch/powerpc/boot/dts/hotfoot.dts linux-2.6.30.hotfoot/arch/powerpc/boot/dts/hotfoot.dts
--- linux-2.6.30/arch/powerpc/boot/dts/hotfoot.dts 1969-12-31 19:00:00.000000000 -0500
+++ linux-2.6.30.hotfoot/arch/powerpc/boot/dts/hotfoot.dts 2009-07-07 12:55:23.000000000 -0400
@@ -0,0 +1,299 @@
+/*
+ * Device Tree Source for ESTeem 195E Hotfoot
+ *
+ * Copyright 2009 AbsoluteValue Systems <solomon at linux-wlan.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "est,hotfoot";
+ compatible = "est,hotfoot";
+ dcr-parent = <&{/cpus/cpu at 0}>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ device_type = "cpu";
+ model = "PowerPC,405EP";
+ reg = <0x00000000>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <0x20>;
+ d-cache-line-size = <0x20>;
+ i-cache-size = <0x4000>;
+ d-cache-size = <0x4000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0x0c0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ plb {
+ compatible = "ibm,plb3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: memory-controller {
+ compatible = "ibm,sdram-405ep";
+ dcr-reg = <0x010 0x002>;
+ };
+
+ MAL: mcmal {
+ compatible = "ibm,mcmal-405ep", "ibm,mcmal";
+ dcr-reg = <0x180 0x062>;
+ num-tx-chans = <4>;
+ num-rx-chans = <2>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xb 0x4 /* TXEOB */
+ 0xc 0x4 /* RXEOB */
+ 0xa 0x4 /* SERR */
+ 0xd 0x4 /* TXDE */
+ 0xe 0x4 /* RXDE */>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-405ep", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0xef600000 0xef600000 0x00a00000>;
+ dcr-reg = <0x0a0 0x005>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ /* Hotfoot has UART0/UART1 swapped */
+
+ UART0: serial at ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600400 0x00000008>;
+ virtual-reg = <0xef600400>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <0x9600>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x1 0x4>;
+ };
+
+ UART1: serial at ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600300 0x00000008>;
+ virtual-reg = <0xef600300>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <0x9600>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x0 0x4>;
+ };
+
+
+ IIC: i2c at ef600500 {
+ compatible = "ibm,iic-405ep", "ibm,iic";
+ reg = <0xef600500 0x00000011>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x2 0x4>;
+
+ rtc at 68 {
+ /* Actually a DS1339 */
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+
+ temp at 4a {
+ /* Not present on all boards */
+ compatible = "national,lm75";
+ reg = <0x4a>;
+ };
+ };
+
+ GPIO: gpio at ef600700 {
+ #gpio-cells = <2>;
+ compatible = "ibm,ppc4xx-gpio";
+ reg = <0xef600700 0x00000020>;
+ gpio-controller;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ status {
+ label = "Status";
+ gpios = <&GPIO 1 0>;
+ /* linux,default=trigger = ".."; */
+ };
+ radiorx {
+ label = "Rx";
+ gpios = <&GPIO 0xe 0>;
+ /* linux,default=trigger = ".."; */
+ };
+ };
+
+
+ EMAC0: ethernet at ef600800 {
+ linux,network-index = <0x0>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xf 0x4 /* Ethernet */
+ 0x9 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600800 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ phy-mode = "mii";
+ phy-map = <0x00000000>;
+ };
+
+ EMAC1: ethernet at ef600900 {
+ linux,network-index = <0x1>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0x11 0x4 /* Ethernet */
+ 0x9 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600900 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <2>;
+ mal-rx-channel = <1>;
+ cell-index = <1>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ mdio-device = <&EMAC0>;
+ phy-mode = "mii";
+ phy-map = <0x0000001>;
+ };
+ };
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-405ep", "ibm,ebc";
+ dcr-reg = <0x012 0x002>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ /* The ranges property is supplied by the bootwrapper
+ * and is based on the firmware's configuration of the
+ * EBC bridge
+ */
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ nor_flash at 0 {
+ compatible = "cfi-flash";
+ bank-width = <2>;
+ reg = <0x0 0xff800000 0x00800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* This mapping is for the 8M flash
+ 4M flash has all ofssets -= 4M,
+ and FeatFS partition is not present */
+
+ partition at 0 {
+ label = "Bootloader";
+ reg = <0x7c0000 0x40000>;
+ /* read-only; */
+ };
+ partition at 1 {
+ label = "Env_and_Config_Primary";
+ reg = <0x400000 0x10000>;
+ };
+ partition at 2 {
+ label = "Kernel";
+ reg = <0x420000 0x100000>;
+ };
+ partition at 3 {
+ label = "Filesystem";
+ reg = <0x520000 0x2a0000>;
+ };
+ partition at 4 {
+ label = "Env_and_Config_Secondary";
+ reg = <0x410000 0x10000>;
+ };
+ partition at 5 {
+ label = "FeatFS";
+ reg = <0x000000 0x400000>;
+ };
+ partition at 6 {
+ label = "Bootloader_Env";
+ reg = <0x7d0000 0x10000>;
+ };
+ };
+ };
+
+ PCI0: pci at ec000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
+ primary;
+ reg = <0xeec00000 0x00000008 /* Config space access */
+ 0xeed80000 0x00000004 /* IACK */
+ 0xeed80000 0x00000004 /* Special cycle */
+ 0xef480000 0x00000040>; /* Internal registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed. Chip supports a second
+ * IO range but we don't use it for now
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
+ 0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
+
+ interrupt-parent = <&UIC0>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 3 -- slot1 (optional) 27/29 A/B IRQ2/4 */
+ 0x1800 0x0 0x0 0x1 &UIC0 0x1b 0x8
+ 0x1800 0x0 0x0 0x2 &UIC0 0x1d 0x8
+
+ /* IDSEL 4 -- slot0, 26/28 A/B IRQ1/3 */
+ 0x2000 0x0 0x0 0x1 &UIC0 0x1a 0x8
+ 0x2000 0x0 0x0 0x2 &UIC0 0x1c 0x8
+ >;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = &UART0;
+ };
+};
diff -Naur linux-2.6.30/arch/powerpc/boot/ppcboot.h linux-2.6.30.hotfoot/arch/powerpc/boot/ppcboot.h
--- linux-2.6.30/arch/powerpc/boot/ppcboot.h 2009-06-09 23:05:27.000000000 -0400
+++ linux-2.6.30.hotfoot/arch/powerpc/boot/ppcboot.h 2009-07-07 12:55:18.000000000 -0400
@@ -52,6 +52,11 @@
unsigned long bi_bootflags; /* boot / reboot flag (for LynxOS) */
unsigned long bi_ip_addr; /* IP Address */
unsigned char bi_enetaddr[6]; /* Ethernet address */
+#if defined(TARGET_HOTFOOT)
+ /* second onboard ethernet port */
+ unsigned char bi_enet1addr[6];
+#define HAVE_ENET1ADDR
+#endif /* TARGET_HOOTFOOT */
unsigned short bi_ethspeed; /* Ethernet speed in Mbps */
unsigned long bi_intfreq; /* Internal Freq, in MHz */
unsigned long bi_busfreq; /* Bus Freq, in MHz */
@@ -74,6 +79,9 @@
unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */
unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */
#endif
+#if defined(TARGET_HOTFOOT)
+ unsigned int bi_pllouta_freq; /* PLL OUTA speed, in Hz */
+#endif
#if defined(TARGET_HYMOD)
hymod_conf_t bi_hymod_conf; /* hymod configuration information */
#endif
@@ -94,6 +102,10 @@
unsigned char bi_enet3addr[6];
#define HAVE_ENET3ADDR
#endif
+#if defined(TARGET_HOTFOOT)
+ int bi_phynum[2]; /* Determines phy mapping */
+ int bi_phymode[2]; /* Determines phy mode */
+#endif
#if defined(TARGET_4xx)
unsigned int bi_opbfreq; /* OB clock in Hz */
int bi_iic_fast[2]; /* Use fast i2c mode */
diff -Naur linux-2.6.30/arch/powerpc/platforms/40x/Kconfig linux-2.6.30.hotfoot/arch/powerpc/platforms/40x/Kconfig
--- linux-2.6.30/arch/powerpc/platforms/40x/Kconfig 2009-06-09 23:05:27.000000000 -0400
+++ linux-2.6.30.hotfoot/arch/powerpc/platforms/40x/Kconfig 2009-07-07 12:55:18.000000000 -0400
@@ -40,6 +40,16 @@
help
This option enables support for the Nestal Maschinen HCU4 board.
+config HOTFOOT
+ bool "Hotfoot"
+ depends on 40x
+ default n
+ select 405EP
+ select PPC40x_SIMPLE
+ select PCI
+ help
+ This option enables support for the ESTEEM 195E Hotfoot board.
+
config KILAUEA
bool "Kilauea"
depends on 40x
diff -Naur linux-2.6.30/arch/powerpc/platforms/40x/ppc40x_simple.c linux-2.6.30.hotfoot/arch/powerpc/platforms/40x/ppc40x_simple.c
--- linux-2.6.30/arch/powerpc/platforms/40x/ppc40x_simple.c 2009-06-09 23:05:27.000000000 -0400
+++ linux-2.6.30.hotfoot/arch/powerpc/platforms/40x/ppc40x_simple.c 2009-07-07 12:55:18.000000000 -0400
@@ -51,7 +51,8 @@
* board.c file for it rather than adding it to this list.
*/
static char *board[] __initdata = {
- "amcc,acadia"
+ "amcc,acadia",
+ "est,hotfoot"
};
static int __init ppc40x_probe(void)
More information about the Linuxppc-dev
mailing list