[PATCH 8/8] powerpc/5200: Rework GPT driver to also be an IRQ controller

[Wolfram Sang]

On Wed, Jan 21, 2009 at 01:55:46PM -0700, Grant Likely wrote:
> From: Grant Likely <grant.likely at secretlab.ca>
> 
> This patch adds IRQ controller support to the MPC5200 General
> Purpose Timer (GPT) device driver.  With this patch the mpc5200-gpt
> driver supports both GPIO and IRQ functions.
> 
> The GPT driver was contained within the mpc52xx_gpio.c file, but this
> patch moves it out into a new file (mpc52xx_gpt.c) since it has more
> than just GPIO functionality now and it was only grouped with the
> mpc52xx-gpio drivers as a matter of convenience before.  Also, this
> driver will most likely get extended again to also provide support
> for the timer function.
> 
> Implementation node: Alternately, I could have tried to implement

"note" instead of "node"? (?too much oftree  error :D)

> the IRQ support as a separate driver and left the GPIO portion alone.
> However, multiple functions of this device (ie. GPIO input+interrupt
> controller, or timer+GPIO) can be active at the same time and the
> registers are shared so it is safer to contain all functionality
> within a single driver.

ACK! I saw the same problem when I wanted to use watchdog+GPIO. Thanks
for doing this!

So far, one comment below...

> 
> Signed-off-by: Grant Likely <grant.likely at secretlab.ca>
> CC: Sascha Hauer <s.hauer at pengutronix.de>
> CC: Wolfram Sang <w.sang at pengutronix.de>
> CC: linuxppc-dev at ozlabs.org
> ---
> 
>  arch/powerpc/platforms/52xx/Makefile       |    2 
>  arch/powerpc/platforms/52xx/mpc52xx_gpio.c |   85 ------
>  arch/powerpc/platforms/52xx/mpc52xx_gpt.c  |  429 ++++++++++++++++++++++++++++
>  3 files changed, 430 insertions(+), 86 deletions(-)
>  create mode 100644 arch/powerpc/platforms/52xx/mpc52xx_gpt.c
> 
> 
> diff --git a/arch/powerpc/platforms/52xx/Makefile b/arch/powerpc/platforms/52xx/Makefile
> index 9dfbde2..bfd4f52 100644
> --- a/arch/powerpc/platforms/52xx/Makefile
> +++ b/arch/powerpc/platforms/52xx/Makefile
> @@ -1,7 +1,7 @@
>  #
>  # Makefile for 52xx based boards
>  #
> -obj-y				+= mpc52xx_pic.o mpc52xx_common.o
> +obj-y				+= mpc52xx_pic.o mpc52xx_common.o mpc52xx_gpt.o
>  obj-$(CONFIG_PCI)		+= mpc52xx_pci.o
>  
>  obj-$(CONFIG_PPC_MPC5200_SIMPLE) += mpc5200_simple.o
> diff --git a/arch/powerpc/platforms/52xx/mpc52xx_gpio.c b/arch/powerpc/platforms/52xx/mpc52xx_gpio.c
> index 07f89ae..2b8d8ef 100644
> --- a/arch/powerpc/platforms/52xx/mpc52xx_gpio.c
> +++ b/arch/powerpc/platforms/52xx/mpc52xx_gpio.c
> @@ -354,88 +354,6 @@ static struct of_platform_driver mpc52xx_simple_gpiochip_driver = {
>  	.remove = mpc52xx_gpiochip_remove,
>  };
>  
> -/*
> - * GPIO LIB API implementation for gpt GPIOs.
> - *
> - * Each gpt only has a single GPIO.
> - */
> -static int mpc52xx_gpt_gpio_get(struct gpio_chip *gc, unsigned int gpio)
> -{
> -	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
> -	struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
> -
> -	return (in_be32(&regs->status) & (1 << (31 - 23))) ? 1 : 0;
> -}
> -
> -static void
> -mpc52xx_gpt_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
> -{
> -	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
> -	struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
> -
> -	if (val)
> -		out_be32(&regs->mode, 0x34);
> -	else
> -		out_be32(&regs->mode, 0x24);
> -
> -	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
> -}
> -
> -static int mpc52xx_gpt_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
> -{
> -	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
> -	struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
> -
> -	out_be32(&regs->mode, 0x04);
> -
> -	return 0;
> -}
> -
> -static int
> -mpc52xx_gpt_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
> -{
> -	mpc52xx_gpt_gpio_set(gc, gpio, val);
> -	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
> -
> -	return 0;
> -}
> -
> -static int __devinit mpc52xx_gpt_gpiochip_probe(struct of_device *ofdev,
> -					const struct of_device_id *match)
> -{
> -	struct of_mm_gpio_chip *mmchip;
> -	struct of_gpio_chip *chip;
> -
> -	mmchip = kzalloc(sizeof(*mmchip), GFP_KERNEL);
> -	if (!mmchip)
> -		return -ENOMEM;
> -
> -	chip = &mmchip->of_gc;
> -
> -	chip->gpio_cells          = 2;
> -	chip->gc.ngpio            = 1;
> -	chip->gc.direction_input  = mpc52xx_gpt_gpio_dir_in;
> -	chip->gc.direction_output = mpc52xx_gpt_gpio_dir_out;
> -	chip->gc.get              = mpc52xx_gpt_gpio_get;
> -	chip->gc.set              = mpc52xx_gpt_gpio_set;
> -
> -	return of_mm_gpiochip_add(ofdev->node, mmchip);
> -}
> -
> -static const struct of_device_id mpc52xx_gpt_gpiochip_match[] = {
> -	{
> -		.compatible = "fsl,mpc5200-gpt-gpio",
> -	},
> -	{}
> -};
> -
> -static struct of_platform_driver mpc52xx_gpt_gpiochip_driver = {
> -	.name = "gpio_gpt",
> -	.match_table = mpc52xx_gpt_gpiochip_match,
> -	.probe = mpc52xx_gpt_gpiochip_probe,
> -	.remove = mpc52xx_gpiochip_remove,
> -};
> -
>  static int __init mpc52xx_gpio_init(void)
>  {
>  	if (of_register_platform_driver(&mpc52xx_wkup_gpiochip_driver))
> @@ -444,9 +362,6 @@ static int __init mpc52xx_gpio_init(void)
>  	if (of_register_platform_driver(&mpc52xx_simple_gpiochip_driver))
>  		printk(KERN_ERR "Unable to register simple GPIO driver\n");
>  
> -	if (of_register_platform_driver(&mpc52xx_gpt_gpiochip_driver))
> -		printk(KERN_ERR "Unable to register gpt GPIO driver\n");
> -
>  	return 0;
>  }
>  
> diff --git a/arch/powerpc/platforms/52xx/mpc52xx_gpt.c b/arch/powerpc/platforms/52xx/mpc52xx_gpt.c
> new file mode 100644
> index 0000000..612a8a3
> --- /dev/null
> +++ b/arch/powerpc/platforms/52xx/mpc52xx_gpt.c
> @@ -0,0 +1,429 @@
> +/*
> + * MPC5200 General Purpose Timer device driver
> + *
> + * Copyright (c) 2009 Secret Lab Technologies Ltd.
> + * Copyright (c) 2008 Sascha Hauer <s.hauer at pengutronix.de>, Pengutronix
> + *
> + * This program is free software; you can redistribute  it and/or modify it
> + * under  the terms of  the GNU General  Public License as published by the
> + * Free Software Foundation;  either version 2 of the  License, or (at your
> + * option) any later version.
> + *
> + * This file is a driver for the the General Purpose Timer (gpt) devices
> + * found on the MPC5200 SoC.  Each timer has an IO pin which can be used
> + * for GPIO or can be used to raise interrupts.  The timer function can
> + * be used independently from the IO pin, or it can be used to control
> + * output signals or measure input signals.
> + *
> + * This driver supports the GPIO and IRQ controller functions of the GPT
> + * device.  Timer functions are not yet supported, nor is the watchdog
> + * timer.
> + *
> + * To use the GPIO function, the following two properties must be added
> + * to the device tree node for the gpt device (typically in the .dts file
> + * for the board):
> + * 	gpio-controller;
> + * 	#gpio-cells = < 2 >;
> + * This driver will register the GPIO pin if it finds the gpio-controller
> + * property in the device tree.
> + *
> + * To use the IRQ controller function, the following two properties must
> + * be added to the device tree node for the gpt device:
> + * 	interrupt-controller;
> + * 	#interrupt-cells = < 1 >;
> + * The IRQ controller binding only uses one cell to specify the interrupt,
> + * and the IRQ flags are encoded in the cell.  A cell is not used to encode
> + * the IRQ number because the GPT only has a single IRQ source.  For flags,
> + * a value of '1' means rising edge sensitive and '2' means falling edge.
> + *
> + * The GPIO and the IRQ controller functions can be used at the same time,
> + * but in this use case the IO line will only work as an input.  Trying to
> + * use it as a GPIO output will not work.
> + *
> + * When using the GPIO line as an output, it can either be driven as normal
> + * IO, or it can be an OC output.  At the moment it is the responsibility
> + * of the bootloader or the platform setup code to set the output mode.
> + * This driver does not change the output mode setting.
> + */
> +
> +#include <linux/irq.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_gpio.h>
> +#include <linux/kernel.h>
> +
> +#include <asm/time.h>
> +#include <asm/prom.h>
> +#include <asm/machdep.h>
> +#include <asm/mpc52xx.h>
> +
> +MODULE_DESCRIPTION("Freescale MPC52xx gpt driver");
> +MODULE_AUTHOR("Sascha Hauer, Grant Likely");
> +MODULE_LICENSE("GPL");
> +
> +/**
> + * struct mpc52xx_gpt - Private data structure for MPC52xx GPT driver
> + * @dev: pointer to device structure
> + * @regs: virtual address of GPT registers
> + * @of_gc: of_gpio_chip instance structure; used when GPIO is enabled
> + * @irqhost: Pointer to irq_host instance; used when IRQ mode is supported
> + */
> +struct mpc52xx_gpt_priv {
> +	struct device *dev;
> +	struct mpc52xx_gpt __iomem *regs;
> +	spinlock_t lock;
> +	struct of_gpio_chip of_gc;
> +	struct irq_host *irqhost;
> +};
> +
> +#define MPC52xx_GPT_GPIO_MODE_MASK	0x00000030
> +#define MPC52xx_GPT_GPIO_MODE_OUTPUT	0x00000020
> +#define MPC52xx_GPT_GPIO_OUTPUT_HIGH	0x00000010
> +
> +/* ---------------------------------------------------------------------
> + * Cascaded interrupt controller hooks
> + */
> +
> +static void mpc52xx_gpt_irq_unmask(unsigned int virq)
> +{
> +	struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
> +	unsigned long flags;
> +
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	out_be32(&gpt->regs->mode, in_be32(&gpt->regs->mode) | 0x100);
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +}
> +
> +static void mpc52xx_gpt_irq_mask(unsigned int virq)
> +{
> +	struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
> +	unsigned long flags;
> +
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	out_be32(&gpt->regs->mode, in_be32(&gpt->regs->mode) & ~0x100);
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +}
> +
> +static void mpc52xx_gpt_irq_ack(unsigned int virq)
> +{
> +	struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
> +
> +	out_be32(&gpt->regs->status, 0xf);
> +}
> +
> +static int mpc52xx_gpt_irq_set_type(unsigned int virq, unsigned int flow_type)
> +{
> +	struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
> +	unsigned long flags;
> +	u32 reg;
> +
> +	dev_dbg(gpt->dev, "%s: virq=%i type=%x\n", __func__, virq, flow_type);
> +
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	reg = in_be32(&gpt->regs->mode) & ~0x30000;

There are lots of magic values in here. A couple of #defines could
help (I know, the original driver has the same problem)?

> +	if (flow_type & IRQF_TRIGGER_RISING)
> +		reg |= 0x10000;

see above...

> +	if (flow_type & IRQF_TRIGGER_FALLING)
> +		reg |= 0x20000;

see above... (okay, I won't mention them all)

> +	out_be32(&gpt->regs->mode, reg);
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +
> +	return 0;
> +}
> +
> +static struct irq_chip mpc52xx_gpt_irq_chip = {
> +	.typename = "MPC52xx GPT",
> +	.unmask = mpc52xx_gpt_irq_unmask,
> +	.mask = mpc52xx_gpt_irq_mask,
> +	.ack = mpc52xx_gpt_irq_ack,
> +	.set_type = mpc52xx_gpt_irq_set_type,
> +};
> +
> +void mpc52xx_gpt_irq_cascade(unsigned int virq, struct irq_desc *desc)
> +{
> +	struct mpc52xx_gpt_priv *gpt = get_irq_data(virq);
> +	int sub_virq;
> +	u32 status;
> +
> +	/* Ask the FPGA for IRQ status.  If 'val' is 0, then no irqs
> +	 * are pending.  'ffs()' is 1 based */
> +	status = in_be32(&gpt->regs->status) | 0xF;
> +	if (status) {
> +		sub_virq = irq_linear_revmap(gpt->irqhost, 0);
> +		generic_handle_irq(sub_virq);
> +	}
> +}
> +
> +static int mpc52xx_gpt_irq_map(struct irq_host *h, unsigned int virq,
> +			       irq_hw_number_t hw)
> +{
> +	struct mpc52xx_gpt_priv *gpt = h->host_data;
> +
> +	dev_dbg(gpt->dev, "%s: h=%p, virq=%i\n", __func__, h, virq);
> +	set_irq_chip_data(virq, gpt);
> +	set_irq_chip_and_handler(virq, &mpc52xx_gpt_irq_chip, handle_edge_irq);
> +
> +	return 0;
> +}
> +
> +static int mpc52xx_gpt_irq_xlate(struct irq_host *h, struct device_node *ct,
> +				 u32 *intspec, unsigned int intsize,
> +				 irq_hw_number_t *out_hwirq,
> +				 unsigned int *out_flags)
> +{
> +	struct mpc52xx_gpt_priv *gpt = h->host_data;
> +
> +	dev_dbg(gpt->dev, "%s: flags=%i\n", __func__, intspec[0]);
> +
> +	if ((intsize < 1) || (intspec[0] < 1) || (intspec[0] > 3)) {
> +		dev_err(gpt->dev, "bad irq specifier in %s\n", ct->full_name);
> +		return -ENODEV;
> +	}
> +
> +	*out_hwirq = 0; /* The GPT only has 1 IRQ line */
> +	*out_flags = intspec[0];
> +
> +	WARN_ON(*out_flags == 0);
> +
> +	return 0;
> +}
> +
> +static struct irq_host_ops mpc52xx_gpt_irq_ops = {
> +	.map = mpc52xx_gpt_irq_map,
> +	.xlate = mpc52xx_gpt_irq_xlate,
> +};
> +
> +static void
> +mpc52xx_gpt_irq_setup(struct mpc52xx_gpt_priv *gpt, struct device_node *node)
> +{
> +	int cascade_virq;
> +	unsigned long flags;
> +	u32 val;
> +
> +	/* Only setup cascaded IRQ if device tree claims the GPT is
> +	 * an interrupt controller */
> +	if (!of_find_property(node, "interrupt-controller", NULL))
> +		return;
> +
> +	cascade_virq = irq_of_parse_and_map(node, 0);
> +
> +	gpt->irqhost = irq_alloc_host(node, IRQ_HOST_MAP_LINEAR, 1,
> +				      &mpc52xx_gpt_irq_ops, -1);
> +	if (!gpt->irqhost) {
> +		dev_err(gpt->dev, "irq_alloc_host() failed\n");
> +		return;
> +	}
> +
> +	gpt->irqhost->host_data = gpt;
> +
> +	set_irq_data(cascade_virq, gpt);
> +	set_irq_chained_handler(cascade_virq, mpc52xx_gpt_irq_cascade);
> +
> +	/* Set to Input Capture mode */
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	val = in_be32(&gpt->regs->mode) & ~0x7;
> +	out_be32(&gpt->regs->mode, val | 0x1); /* IC mode */
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +
> +	dev_dbg(gpt->dev, "%s() complete. virq=%i\n", __func__, cascade_virq);
> +
> +	return;
> +}
> +
> +
> +/* ---------------------------------------------------------------------
> + * GPIOLIB hooks
> + */
> +#if defined(CONFIG_GPIOLIB)
> +static inline struct mpc52xx_gpt_priv *gc_to_mpc52xx_gpt(struct gpio_chip *gc)
> +{
> +	return container_of(to_of_gpio_chip(gc), struct mpc52xx_gpt_priv,of_gc);
> +}
> +
> +static int mpc52xx_gpt_gpio_get(struct gpio_chip *gc, unsigned int gpio)
> +{
> +	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
> +
> +	return (in_be32(&gpt->regs->status) >> 8) & 1;
> +}
> +
> +static void
> +mpc52xx_gpt_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
> +{
> +	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
> +	unsigned long flags;
> +	u32 tmp;
> +
> +	dev_dbg(gpt->dev, "%s: gpio:%d val:%d\n", __func__, gpio, val);
> +
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	tmp = in_be32(&gpt->regs->mode) & ~MPC52xx_GPT_GPIO_MODE_MASK;
> +	out_be32(&gpt->regs->mode, tmp | (val ? 0x30 : 0x20));
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +}
> +
> +static int mpc52xx_gpt_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
> +{
> +	struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
> +	unsigned long flags;
> +	u32 tmp;
> +
> +	dev_dbg(gpt->dev, "%s: gpio:%d\n", __func__, gpio);
> +
> +	spin_lock_irqsave(&gpt->lock, flags);
> +	tmp = in_be32(&gpt->regs->mode) & ~MPC52xx_GPT_GPIO_MODE_MASK;
> +	out_be32(&gpt->regs->mode, tmp);
> +	spin_unlock_irqrestore(&gpt->lock, flags);
> +
> +	return 0;
> +}
> +
> +static int
> +mpc52xx_gpt_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
> +{
> +	mpc52xx_gpt_gpio_set(gc, gpio, val);
> +	return 0;
> +}
> +
> +static void
> +mpc52xx_gpt_gpio_setup(struct mpc52xx_gpt_priv *gpt, struct device_node *node)
> +{
> +	int rc;
> +
> +	/* Only setup GPIO if the device tree claims the GPT is
> +	 * a GPIO controller */
> +	if (!of_find_property(node, "gpio-controller", NULL))
> +		return;
> +
> +	gpt->of_gc.gc.label = kstrdup(node->full_name, GFP_KERNEL);
> +	if (!gpt->of_gc.gc.label) {
> +		dev_err(gpt->dev, "out of memory\n");
> +		return;
> +	}
> +
> +	gpt->of_gc.gpio_cells = 2;
> +	gpt->of_gc.gc.ngpio = 1;
> +	gpt->of_gc.gc.direction_input  = mpc52xx_gpt_gpio_dir_in;
> +	gpt->of_gc.gc.direction_output = mpc52xx_gpt_gpio_dir_out;
> +	gpt->of_gc.gc.get = mpc52xx_gpt_gpio_get;
> +	gpt->of_gc.gc.set = mpc52xx_gpt_gpio_set;
> +	gpt->of_gc.gc.base = -1;
> +	gpt->of_gc.xlate = of_gpio_simple_xlate;
> +	node->data = &gpt->of_gc;
> +	of_node_get(node);
> +
> +	rc = gpiochip_add(&gpt->of_gc.gc);
> +	if (rc)
> +		dev_err(gpt->dev, "gpiochip_add() failed; rc=%i\n", rc);
> +
> +	dev_dbg(gpt->dev, "%s() complete.\n", __func__);
> +}
> +#else /* defined(CONFIG_GPIOLIB) */
> +static void
> +mpc52xx_gpt_gpio_setup(struct mpc52xx_gpt_priv *, struct device_node *) { }
> +#endif /* defined(CONFIG_GPIOLIB) */
> +
> +/***********************************************************************
> + * SYSFS attributes
> + */
> +#if defined(CONFIG_SYSFS)
> +static ssize_t mpc52xx_gpt_show_regs(struct device *dev,
> +				     struct device_attribute *attr, char *buf)
> +{
> +	struct mpc52xx_gpt_priv *gpt = dev_get_drvdata(dev);
> +	int i, len = 0;
> +	u32 __iomem *regs = (void __iomem *) gpt->regs;
> +
> +	for (i = 0; i < 4; i++)
> +		len += sprintf(buf + len, "%.8x ", in_be32(regs + i));
> +	len += sprintf(buf + len, "\n");
> +
> +	return len;
> +}
> +
> +static struct device_attribute mpc52xx_gpt_attrib[] = {
> +	__ATTR(regs, S_IRUGO | S_IWUSR, mpc52xx_gpt_show_regs, NULL),
> +};
> +
> +static void mpc52xx_gpt_create_attribs(struct mpc52xx_gpt_priv *gpt)
> +{
> +	int i, err = 0;
> +
> +	for (i = 0; i < ARRAY_SIZE(mpc52xx_gpt_attrib); i++)
> +		err |= device_create_file(gpt->dev, &mpc52xx_gpt_attrib[i]);
> +
> +	if (err)
> +		dev_err(gpt->dev, "device_create_file() failed\n");
> +}
> +
> +#else /* defined(CONFIG_SYSFS) */
> +static void mpc52xx_gpt_create_attribs(struct mpc52xx_gpt_priv *) { return 0; }
> +#endif /* defined(CONFIG_SYSFS) */
> +
> +/* ---------------------------------------------------------------------
> + * of_platform bus binding code
> + */
> +static int __devinit mpc52xx_gpt_probe(struct of_device *ofdev,
> +				       const struct of_device_id *match)
> +{
> +	struct mpc52xx_gpt_priv *gpt;
> +	u32 val;
> +
> +	gpt = kzalloc(sizeof *gpt, GFP_KERNEL);
> +	if (!gpt)
> +		return -ENOMEM;
> +
> +	spin_lock_init(&gpt->lock);
> +	gpt->dev = &ofdev->dev;
> +	gpt->regs = of_iomap(ofdev->node, 0);
> +	if (!gpt->regs) {
> +		kfree(gpt);
> +		return -ENOMEM;
> +	}
> +
> +	/* Setup external pin in GPIO mode */
> +	val = in_be32(&gpt->regs->mode) & ~0x7;
> +	out_be32(&gpt->regs->mode, val | 0x4);
> +
> +	dev_set_drvdata(&ofdev->dev, gpt);
> +
> +	mpc52xx_gpt_create_attribs(gpt);
> +	mpc52xx_gpt_gpio_setup(gpt, ofdev->node);
> +	mpc52xx_gpt_irq_setup(gpt, ofdev->node);
> +
> +	return 0;
> +}
> +
> +static int mpc52xx_gpt_remove(struct of_device *ofdev)
> +{
> +	return -EBUSY;
> +}
> +
> +static const struct of_device_id mpc52xx_gpt_match[] = {
> +	{ .compatible = "fsl,mpc5200-gpt", },
> +
> +	/* Depreciated compatible values; don't use for new dts files */
> +	{ .compatible = "fsl,mpc5200-gpt-gpio", },
> +	{ .compatible = "mpc5200-gpt", },
> +	{}
> +};
> +
> +static struct of_platform_driver mpc52xx_gpt_driver = {
> +	.name = "mpc52xx-gpt",
> +	.match_table = mpc52xx_gpt_match,
> +	.probe = mpc52xx_gpt_probe,
> +	.remove = mpc52xx_gpt_remove,
> +};
> +
> +static int __init mpc52xx_gpt_init(void)
> +{
> +	if (of_register_platform_driver(&mpc52xx_gpt_driver))
> +		pr_err("error registering MPC52xx GPT driver\n");
> +
> +	return 0;
> +}
> +
> +/* Make sure GPIOs and IRQs get set up before anyone tries to use them */
> +subsys_initcall(mpc52xx_gpt_init);
> 

-- 
  Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
 Pengutronix - Linux Solutions for Science and Industry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 197 bytes
Desc: Digital signature
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20090127/9bb88c73/attachment.pgp>