Newby trying to get Ethernet going on MPC83xx series device.

[Dushara Jayasinghe]

That did it.

I based my board specific file on mpc834x_itx.c which had

static struct of_device_id __initdata mpc834x_itx_ids[] = {
                { .compatible = "fsl,pq2pro-localbus", },
                { .compatible = "simple-bus", },
                {},
};

Don't know if this is broken?

From: Aggrwal Poonam-B10812 [mailto:Poonam.Aggrwal at freescale.com]
Sent: Thursday, 19 February 2009 5:49 PM
To: Li Yang-R58472; Dushara Jayasinghe; linuxppc-dev at ozlabs.org
Subject: RE: Newby trying to get Ethernet going on MPC83xx series device.


Can you look into your board specific file
Like board/freescale/mpc8249_mds/mpc8349_mds.c

And check if the buses are getting probed.

For example

static struct of_device_id mpc834x_ids[] = {
        { .type = "soc", },
        { .compatible = "soc", },
        { .compatible = "simple-bus", },
        {},
};

static int __init mpc834x_declare_of_platform_devices(void)
{
        of_platform_bus_probe(NULL, mpc834x_ids, NULL);
        return 0;
}
machine_device_initcall(mpc834x_mds, mpc834x_declare_of_platform_devices);

Regards
Poonam


> -----Original Message-----
> From:
> linuxppc-dev-bounces+poonam.aggrwal=freescale.com at ozlabs.org
> [mailto:linuxppc-dev-bounces+poonam.aggrwal=freescale.com at ozla
> bs.org] On Behalf Of Li Yang-R58472
> Sent: Thursday, February 19, 2009 10:52 AM
> To: Dushara Jayasinghe; linuxppc-dev at ozlabs.org
> Subject: RE: Newby trying to get Ethernet going on MPC83xx
> series device.
>
> > -----Original Message-----
> > From: linuxppc-dev-bounces+leoli=freescale.com at ozlabs.org
> > [mailto:linuxppc-dev-bounces+leoli=freescale.com at ozlabs.org]
> > On Behalf Of Dushara Jayasinghe
> > Sent: Thursday, February 19, 2009 12:27 PM
> > To: 'linuxppc-dev at ozlabs.org'
> > Subject: Newby trying to get Ethernet going on MPC83xx
> series device.
> >
> > Hi I'm having difficulty getting an Ethernet device up on a
> dev board
> > with an MPX8349 controller.
> >
> > The contents of my .dts file are as follows (based on
> > mpc8349emitx.dts):
> >
> >         soc8349 at e0000000 {
> >                 ...
> >
> >                 mdio at 24520 {
> >                         #address-cells = <1>;
> >                         #size-cells = <0>;
> >                         compatible = "fsl,gianfar-mdio";
> >                         reg = <24520 20>;
> >
> >                         /* Vitesse 8201 */
> >                         phy1c: ethernet-phy at 1c {
> >                                 interrupt-parent = <&ipic>;
> >                                 interrupts = <3 8>;
> >                                 reg = <0>;
> >                                 device_type = "ethernet-phy";
> >                         };
> >                         tbi0: tbi-phy at 11 {
> >                                 reg = <11>;
> >                                 device_type = "tbi-phy";
> >                         };
> >                 };
> >
> >                 mdio at 25520 {
> >                         #address-cells = <1>;
> >                         #size-cells = <0>;
> >                         compatible = "fsl,gianfar-tbi";
> >                         reg = <25520 20>;
> >
> >                         tbi1: tbi-phy at 11 {
> >                                 reg = <11>;
> >                                 device_type = "tbi-phy";
> >                         };
> >                 };
> >
> >                 ethernet at 24000 {
> >                         cell-index = <0>;
> >                         device_type = "network";
> >                         model = "TSEC";
> >                         compatible = "gianfar";
> >                         reg = <24000 1000>;
> >                         local-mac-address = [ 00 00 00 00 00 00 ];
> >                         interrupts = <20 8 21 8 22 8>;
> >                         interrupt-parent = <&ipic>;
> >                         tbi-handle = <&tbi0>;
> >                         phy-handle = <&phy1c>;
> >                         linux,network-index = <0>;
> >                 };
> >
> >                 ethernet at 25000 {
> >                         cell-index = <1>;
> >                         device_type = "network";
> >                         model = "TSEC";
> >                         compatible = "gianfar";
> >                         reg = <25000 1000>;
> >                         local-mac-address = [ 00 00 00 00 00 00 ];
> >                         interrupts = <23 8 24 8 25 8>;
> >                         interrupt-parent = <&ipic>;
> >                         /* Vitesse 7385 isn't on the MDIO bus */
> >                         fixed-link = <1 1 1000 0 0>;
> >                         linux,network-index = <1>;
> >                         tbi-handle = <&tbi1>;
> >                         phy-connection-type = "gmii";
> >                 };
> >         };
> >
> > I get the following error during the boot sequence:
> >
> > IP-Config: Device `eth0' not found
> >
> > I also found that both gfar_init (in gianfar.c) and
> gfar_mdio_init (in
> > gianfar_mii.c) are called but the probe handlers of either of these
> > devices are not executed.
> >
> > What am I missing?
>
> Don't find any obvious problem.  I suggest you to debug
> gfar_of_init() in arch/powerpc/sysdev/fsl_soc.c to see if it
> works correctly.
>
> - Leo
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev at ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20090219/d91e1ed8/attachment.htm>