MPC5200 PCI Issues
Tobias Knutsson
tobias.knutsson at gmail.com
Fri Feb 6 22:46:44 EST 2009
Ok, I have had a breakthrough. I was trying to find out where the
resources were supposed to be allocated and that was when i found this
section of code in pbus_assign_resources_sorted() in
drivers/pci/setup-bus.c:
/* Don't touch classless devices or host bridges or ioapics. */
if (class == PCI_CLASS_NOT_DEFINED ||
class == PCI_CLASS_BRIDGE_HOST)
continue;
After that i took a quick look at the PCI-info reported by u-boot.
Sure enough, all boards were reported having class 0. At first i tried
to write a different class type, but as i suspected, the register
seems to be read-only. Therefore I simply commented out the first part
of the if-statement and now the resources seems to get allocated
properly.
However, I do realize that this is not the proper way of solving this
issue. Any ideas on how to fix it without modifying any kernel code?
On Thu, Feb 5, 2009 at 21:03, Tobias Knutsson <tobias.knutsson at gmail.com> wrote:
>
> Hi,
>
> That is exactly what the bootlog shows. Debug output on in both
> mpc52xx_pci.c and in pci-common.c. And the discussed code section enabled.
>
> Hälsningar / Regards
> Tobias Knutsson
>
> On 5 feb 2009, at 17.44, Grant Likely <grant.likely at secretlab.ca> wrote:
>
>> On Thu, Feb 5, 2009 at 12:06 AM, Tobias Knutsson
>> <tobias.knutsson at gmail.com> wrote:
>>>
>>> When enabling the debug-printouts, it came to me that I forgot to
>>> mention something kind of important. Using the standard mpc52xx_pci.c,
>>> even the memory resources are mapped to zero.
>>>
>>> After disabling this code block, the memory regions are mapped out
>>> fine (but still no IO):
>>
>> Reenable this code, enable debug in arch/powerpc/kernel/pci-common.c,
>> and post the results.
>>
>> When this code is disabled then you're just getting the leftovers from
>> U-Boot's scan of the PCI bus. For MPC5200 support Linux does its own
>> scan and its own allocation of memory/IO address space and this code
>> is needed to make sure that happens.
>>
>> g.
>>
>>>
>>> static void
>>> mpc52xx_pci_fixup_resources(struct pci_dev *dev)
>>> {
>>> int i;
>>>
>>> pr_debug("mpc52xx_pci_fixup_resources() %.4x:%.4x\n",
>>> dev->vendor, dev->device);
>>>
>>> /* We don't rely on boot loader for PCI and resets all
>>> devices */
>>> for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
>>> struct resource *res = &dev->resource[i];
>>> if (res->end > res->start) { /* Only valid resources */
>>> res->end -= res->start;
>>> res->start = 0;
>>> res->flags |= IORESOURCE_UNSET;
>>> }
>>> }
>>>
>>> What is the purpose of this code? Since all resources are reset here,
>>> where are they inteded to be re-allocated?
>>>
>>> Here is the bootlog with the aforementioned code enabled:
>>>
>>>
>>> reading cuImage.lite5200b
>>>
>>> 1833699 bytes read
>>> ## Booting kernel from Legacy Image at 00201400 ...
>>> Image Name: Linux-2.6.28
>>> Created: 2009-02-05 6:54:20 UTC
>>> Image Type: PowerPC Linux Kernel Image (gzip compressed)
>>> Data Size: 1833635 Bytes = 1.7 MB
>>> Load Address: 00400000
>>> Entry Point: 004005a0
>>> Verifying Checksum ... OK
>>> Uncompressing Kernel Image ... OK
>>> [ 0.000000] Using lite5200 machine description
>>> [ 0.000000] Linux version 2.6.28 (tknutsson at ztn-ubuntu) (gcc
>>> version 4.3.2 (Sourcery G++ Lite 4.3-50) ) #66 Thu Feb 5 07:51:46 CET
>>> 2009
>>> [ 0.000000] Adding MPC52xx PCI host bridge /pci at f0000d00
>>> [ 0.000000] PCI host bridge /pci at f0000d00 (primary) ranges:
>>> [ 0.000000] MEM 0x0000000050000000..0x000000005fffffff ->
>>> 0x0000000050000000
>>> [ 0.000000] IO 0x0000000060000000..0x0000000060ffffff ->
>>> 0x0000000000000000
>>> [ 0.000000] mpc52xx_pci_setup(hose=c03ec000, pci_regs=fdffad00)
>>> [ 0.000000] mem_resource[0] = {.start=50000000, .end=5fffffff,
>>> .flags=200}
>>> [ 0.000000] .io_resource={.start=0,.end=ffffff,.flags=100}
>>> .io_base_phys=0x60000000
>>> [ 0.000000] Zone PFN ranges:
>>> [ 0.000000] DMA 0x00000000 -> 0x00004000
>>> [ 0.000000] Normal 0x00004000 -> 0x00004000
>>> [ 0.000000] Movable zone start PFN for each node
>>> [ 0.000000] early_node_map[1] active PFN ranges
>>> [ 0.000000] 0: 0x00000000 -> 0x00004000
>>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
>>> Total pages: 16256
>>> [ 0.000000] Kernel command line: console=ttyPSC0,115200 root=/dev/sda2
>>> rw
>>> [ 0.000000] MPC52xx PIC is up and running!
>>> [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
>>> [ 0.000000] clocksource: timebase mult[7d00000] shift[22] registered
>>> [ 0.000263] console [ttyPSC0] enabled
>>> [ 0.121690] Dentry cache hash table entries: 8192 (order: 3, 32768
>>> bytes)
>>> [ 0.129012] Inode-cache hash table entries: 4096 (order: 2, 16384
>>> bytes)
>>> [ 0.147433] Memory: 60844k/65536k available (3704k kernel code,
>>> 4624k reserved, 156k data, 117k bss, 180k init)
>>> [ 0.157672] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0,
>>> CPUs=1, Nodes=1
>>> [ 0.165373] Calibrating delay loop... 63.87 BogoMIPS (lpj=127744)
>>> [ 0.236265] Mount-cache hash table entries: 512
>>> [ 0.245719] net_namespace: 288 bytes
>>> [ 0.250237] NET: Registered protocol family 16
>>> [ 0.284887] PCI: Probing PCI hardware
>>> [ 0.289670] mpc52xx_pci_fixup_resources() 1057:5809
>>> [ 0.294799] PCI:0000:00:17.0 Resource 0
>>> 0000000050400000-00000000507fffff [21208] fixup...
>>> [ 0.303180] PCI:0000:00:17.0
>>> 0000000050400000-00000000507fffff
>>> [ 0.309998] PCI:0000:00:17.0 Resource 1
>>> 0000000050800000-0000000050ffffff [20200] fixup...
>>> [ 0.318262] PCI:0000:00:17.0
>>> 0000000050800000-0000000050ffffff
>>> [ 0.325062] PCI:0000:00:17.0 Resource 2
>>> 0000000060000000-000000006000000f [20101] fixup...
>>> [ 0.333326] PCI:0000:00:17.0
>>> 0000000060000000-000000006000000f
>>> [ 0.340124] mpc52xx_pci_fixup_resources() 104c:9065
>>> [ 0.345242] PCI:0000:00:18.0 Resource 0
>>> 0000000051000000-00000000513fffff [21208] fixup...
>>> [ 0.353519] PCI:0000:00:18.0
>>> 0000000051000000-00000000513fffff
>>> [ 0.360319] PCI:0000:00:18.0 Resource 1
>>> 0000000051800000-0000000051ffffff [20200] fixup...
>>> [ 0.368583] PCI:0000:00:18.0
>>> 0000000051800000-0000000051ffffff
>>> [ 0.375383] PCI:0000:00:18.0 Resource 2
>>> 0000000060000010-000000006000001f [20101] fixup...
>>> [ 0.383647] PCI:0000:00:18.0
>>> 0000000060000010-000000006000001f
>>> [ 0.390444] mpc52xx_pci_fixup_resources() 104c:9065
>>> [ 0.395549] PCI:0000:00:19.0 Resource 0
>>> 0000000052000000-00000000523fffff [21208] fixup...
>>> [ 0.403826] PCI:0000:00:19.0
>>> 0000000052000000-00000000523fffff
>>> [ 0.410626] PCI:0000:00:19.0 Resource 1
>>> 0000000052800000-0000000052ffffff [20200] fixup...
>>> [ 0.418889] PCI:0000:00:19.0
>>> 0000000052800000-0000000052ffffff
>>> [ 0.425690] PCI:0000:00:19.0 Resource 2
>>> 0000000060000020-000000006000002f [20101] fixup...
>>> [ 0.433954] PCI:0000:00:19.0
>>> 0000000060000020-000000006000002f
>>> [ 0.440751] mpc52xx_pci_fixup_resources() 104c:9065
>>> [ 0.445854] PCI:0000:00:1a.0 Resource 0
>>> 0000000053000000-00000000533fffff [21208] fixup...
>>> [ 0.454130] PCI:0000:00:1a.0
>>> 0000000053000000-00000000533fffff
>>> [ 0.460930] PCI:0000:00:1a.0 Resource 1
>>> 0000000053800000-0000000053ffffff [20200] fixup...
>>> [ 0.469194] PCI:0000:00:1a.0
>>> 0000000053800000-0000000053ffffff
>>> [ 0.475994] PCI:0000:00:1a.0 Resource 2
>>> 0000000060000030-000000006000003f [20101] fixup...
>>> [ 0.484258] PCI:0000:00:1a.0
>>> 0000000060000030-000000006000003f
>>> [ 0.491056] mpc52xx_pci_fixup_resources() 104c:9065
>>> [ 0.495999] PCI: Fixup bus 0 (PHB)
>>> [ 0.499383] PCI: device 0000:00:16.0 OF node: <none>
>>> [ 0.504371] PCI: device 0000:00:17.0 OF node: <none>
>>> [ 0.509363] PCI: device 0000:00:18.0 OF node: <none>
>>> [ 0.514354] PCI: device 0000:00:19.0 OF node: <none>
>>> [ 0.519345] PCI: device 0000:00:1a.0 OF node: <none>
>>> [ 0.524332] Try to map irq for 0000:00:16.0...
>>> [ 0.528808] Try to map irq for 0000:00:17.0...
>>> [ 0.533334] -> got one, spec 3 cells (0x00000001 0x00000001...) on
>>> /soc5200 at f0000000/interrupt-controller at 500
>>> [ 0.543389] -> mapped to linux irq 65
>>> [ 0.547117] Try to map irq for 0000:00:18.0...
>>> [ 0.551626] -> got one, spec 3 cells (0x00000001 0x00000001...) on
>>> /soc5200 at f0000000/interrupt-controller at 500
>>> [ 0.561629] -> mapped to linux irq 65
>>> [ 0.565353] Try to map irq for 0000:00:19.0...
>>> [ 0.569858] -> got one, spec 3 cells (0x00000001 0x00000001...) on
>>> /soc5200 at f0000000/interrupt-controller at 500
>>> [ 0.579863] -> mapped to linux irq 65
>>> [ 0.583587] Try to map irq for 0000:00:1a.0...
>>> [ 0.588099] -> got one, spec 3 cells (0x00000001 0x00000001...) on
>>> /soc5200 at f0000000/interrupt-controller at 500
>>> [ 0.598103] -> mapped to linux irq 65
>>> [ 0.605144] PCI: PHB (bus 0) bridge rsrc 0:
>>> 0000000000000000-0000000000ffffff [0x100], parent c03a1fdc (PCI IO)
>>> [ 0.615266] PCI: PHB (bus 0) bridge rsrc 1:
>>> 0000000050000000-000000005fffffff [0x200], parent c03a1fc0 (PCI mem)
>>> [ 0.625539] PCI: Assigning unassigned resouces...
>>> [ 0.630304] bus: 00 index 0 io port: [0x00-0xffffff]
>>> [ 0.635299] bus: 00 index 1 mmio: [0x50000000-0x5fffffff]
>>> [ 0.640909] DMA: MPC52xx BestComm driver
>>> [ 0.645214] DMA: MPC52xx BestComm engine @f0001200 ok !
>>> [ 0.678739] SCSI subsystem initialized
>>> [ 0.709498] NET: Registered protocol family 2
>>> [ 0.754980] IP route cache hash table entries: 1024 (order: 0, 4096
>>> bytes)
>>> [ 0.762429] TCP established hash table entries: 2048 (order: 2, 16384
>>> bytes)
>>> [ 0.769716] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
>>> [ 0.776224] TCP: Hash tables configured (established 2048 bind 2048)
>>> [ 0.782604] TCP reno registered
>>> [ 0.795054] NET: Registered protocol family 1
>>> [ 0.846171] JFFS2 version 2.2. (NAND) (c) 2001-2006 Red Hat, Inc.
>>> [ 0.855699] msgmni has been set to 118
>>> [ 0.861227] alg: No test for stdrng (krng)
>>> [ 0.865651] io scheduler noop registered
>>> [ 0.869658] io scheduler anticipatory registered (default)
>>> [ 0.875224] io scheduler deadline registered
>>> [ 0.879838] io scheduler cfq registered
>>> [ 1.442231] Generic RTC Driver v1.07
>>> [ 1.447145] Serial: MPC52xx PSC UART driver
>>> [ 1.451885] f0002200.serial: ttyPSC2 at MMIO 0xf0002200 (irq = 130)
>>> is a MPC52xx PSC
>>> [ 1.461497] f0002400.serial: ttyPSC3 at MMIO 0xf0002400 (irq = 131)
>>> is a MPC52xx PSC
>>> [ 1.471257] f0002600.serial: ttyPSC4 at MMIO 0xf0002600 (irq = 139)
>>> is a MPC52xx PSC
>>> [ 1.480866] f0002800.serial: ttyPSC5 at MMIO 0xf0002800 (irq = 140)
>>> is a MPC52xx PSC
>>> [ 1.490461] f0002c00.serial: ttyPSC0 at MMIO 0xf0002c00 (irq = 132)
>>> is a MPC52xx PSC
>>> [ 1.521689] brd: module loaded
>>> [ 1.535886] loop: module loaded
>>> [ 1.544328] mpc52xx MII bus: probed
>>> [ 1.550220] net eth0: Using PHY at MDIO address 0
>>> [ 1.556124] Driver 'sd' needs updating - please use bus_type methods
>>> [ 1.563224] ata: MPC52xx IDE/ATA libata driver
>>> [ 1.568729] scsi0 : mpc52xx_ata
>>> [ 1.573032] ata1: PATA max UDMA/33 ata_regs 0xf0003a00 irq 135
>>> [ 1.751224] ata1.00: ATA-0: TRANSCEND, 20070831, max UDMA/66
>>> [ 1.756948] ata1.00: 3915072 sectors, multi 0: LBA
>>> [ 1.775156] ata1.00: configured for UDMA/33
>>> [ 1.803154] ata1.00: configured for UDMA/33
>>> [ 1.807423] ata1: EH complete
>>> [ 1.811300] scsi 0:0:0:0: Direct-Access ATA TRANSCEND
>>> 2007 PQ: 0 ANSI: 5
>>> [ 1.821337] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
>>> (2.00 GB/1.86 GiB)
>>> [ 1.829333] sd 0:0:0:0: [sda] Write Protect is off
>>> [ 1.834879] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
>>> enabled, doesn't support DPO or FUA
>>> [ 1.844851] sd 0:0:0:0: [sda] 3915072 512-byte hardware sectors:
>>> (2.00 GB/1.86 GiB)
>>> [ 1.852841] sd 0:0:0:0: [sda] Write Protect is off
>>> [ 1.858259] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
>>> enabled, doesn't support DPO or FUA
>>> [ 1.867450] sda: sda1 sda2
>>> [ 1.881490] sd 0:0:0:0: [sda] Attached SCSI disk
>>> [ 1.890711] fc000000.flash: Found 1 x16 devices at 0x0 in 8-bit bank
>>> [ 1.897222] Amd/Fujitsu Extended Query Table at 0x0040
>>> [ 1.902529] fc000000.flash: CFI does not contain boot bank
>>> location. Assuming top.
>>> [ 1.910147] number of CFI chips: 1
>>> [ 1.913603] cfi_cmdset_0002: Disabling erase-suspend-program due to
>>> code brokenness.
>>> [ 1.922009] RedBoot partition parsing not available
>>> [ 1.926998] Creating 4 MTD partitions on "fc000000.flash":
>>> [ 1.932547] 0x00000000-0x00500000 : "u-boot"
>>> [ 1.940601] 0x00500000-0x01000000 : "kernel"
>>> [ 1.948071] 0x01000000-0x02000000 : "rootfs"
>>> [ 1.955601] 0x02000000-0x03000000 : "application"
>>> [ 1.964240] i2c /dev entries driver
>>> [ 1.975775] Advanced Linux Sound Architecture Driver Version
>>> 1.0.18rc3.
>>> [ 1.983814] ASoC version 0.13.2
>>> [ 1.987668] tlv320aic23 0-001a: probing tlv320aic23 i2c device
>>> [ 2.040451] registering ASoC codec driver:
>>> /soc5200 at f0000000/i2c at 3d00/codec at 1a
>>> [ 2.049539] ALSA device list:
>>> [ 2.052591] No soundcards found.
>>> [ 2.057430] TCP cubic registered
>>> [ 2.060765] NET: Registered protocol family 17
>>> [ 2.066886] RPC: Registered udp transport module.
>>> [ 2.071683] RPC: Registered tcp transport module.
>>> [ 2.087086] EXT2-fs warning: mounting unchecked fs, running e2fsck
>>> is recommended
>>> [ 2.094828] VFS: Mounted root (ext2 filesystem).
>>> [ 2.099690] Freeing unused kernel memory: 180k init
>>>
>>> On Wed, Feb 4, 2009 at 18:54, Grant Likely <grant.likely at secretlab.ca>
>>> wrote:
>>>>
>>>> On Wed, Feb 4, 2009 at 9:53 AM, Tobias Knutsson
>>>> <tobias.knutsson at gmail.com> wrote:
>>>>>
>>>>> clock-frequency = <0x1e84800>; //<0>; // From boot loader
>>>>> interrupts = <2 8 0 2 9 0 2 10 0>;
>>>>> interrupt-parent = <&mpc5200_pic>;
>>>>> bus-range = <0 0>;
>>>>> ranges = <0x02000000 0 0x50000000 0x50000000 0 0x10000000
>>>>> 0x01000000 0 0x00000000 0x60000000 0 0x01000000>;
>>>>> };
>>>>>
>>>>> The cards' memory regions are mapped out fine to different addresses
>>>>> in the 0x50000000-0x60000000 range. However, the IO regions are all
>>>>> mapped
>>>>> to zero.
>>>>>
>>>>> Do you have any idea on what could be wrong or in which direction I
>>>>> should be looking?
>>>>
>>>> Hmmm. Your ranges property looks okay to me. The MPC5200 setup code
>>>> may be doing the wrong thing. Turn on debug at the top of
>>>> arch/powerpc/platforms/mpc52xx/mpc52xx_pci.c and post your kernel
>>>> output.
>>>>
>>>> g.
>>>>
>>>> --
>>>> Grant Likely, B.Sc., P.Eng.
>>>> Secret Lab Technologies Ltd.
>>>>
>>>
>>>
>>>
>>> --
>>>
>>> Hälsningar/Regards
>>> Tobias Knutsson
>>>
>>
>>
>>
>> --
>> Grant Likely, B.Sc., P.Eng.
>> Secret Lab Technologies Ltd.
>
--
Hälsningar/Regards
Tobias Knutsson
More information about the Linuxppc-dev
mailing list