[PATCH] Adding PCI-E support for 460SX based redwood board.

Tirumala Reddy Marri tmarri at amcc.com
Thu Dec 10 13:22:18 EST 2009


Testing  and other information for this patch.

1. Kernel version: 2.6.32-rc6 
2. Board:  AMCC redwood validation board.
3. tests
   a. Configured redwood boards PCI-E ports as root ports. And plugged
in 2 HBA sas cards with 8 drives each. XDD and IO   
      meter tests were ran. No issues found.
   b. Configured redwood board PCI-E port as Endpoint and configured
second board as root complex.  Boards were interconnected using PCI-E
cable. Then did lspci on root complex configured redwood board to see if
the endpoint can be scanned. Also using BDI I was able to do read and
writes to & from root complex as well as endpoint.


Regards,
Marri

-----Original Message-----
From: tmarr at amcc.com [mailto:tmarr at amcc.com] 
Sent: Monday, November 30, 2009 1:16 PM
To: benh at kernel.crashing.org
Cc: linuxppc-dev at ozlabs.org; Tirumala Reddy Marri
Subject: [PATCH] Adding PCI-E support for 460SX based redwood board.

From: Tirumala Marri <tmarri at amcc.com>

This patch would add PCI-E support for AMCC 460SX processor based 
redwood board.

Signed-off-by: Tirumala Marri <tmarri at amcc.com>

---
 arch/powerpc/boot/dts/redwood.dts |  122
+++++++++++++++++++++++++++++++++++++
 arch/powerpc/sysdev/ppc4xx_pci.c  |  119
++++++++++++++++++++++++++++++++++++
 arch/powerpc/sysdev/ppc4xx_pci.h  |   58 +++++++++++++++++
 3 files changed, 299 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/boot/dts/redwood.dts
b/arch/powerpc/boot/dts/redwood.dts
index ad402c4..9eeec28 100644
--- a/arch/powerpc/boot/dts/redwood.dts
+++ b/arch/powerpc/boot/dts/redwood.dts
@@ -233,6 +233,128 @@
 				has-inverted-stacr-oc;
 				has-new-stacr-staopc;
 			};
+			PCIE0: pciex at d00000000 {
+				device_type = "pci";
+				#interrupt-cells = <1>;
+				#size-cells = <2>;
+				#address-cells = <3>;
+				compatible = "ibm,plb-pciex-460sx",
"ibm,plb-pciex";
+				primary;
+				port = <0x0>; /* port number */
+				reg = <0x0000000d 0x00000000 0x20000000
/* Config space access */
+				       0x0000000c 0x10000000
0x00001000>;	/* Registers */
+				dcr-reg = <0x100 0x020>;
+				sdr-base = <0x300>;
+
+				/* Outbound ranges, one memory and one
IO,
+				 * later cannot be changed
+				 */
+				ranges = <0x02000000 0x00000000
0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000
+					  0x01000000 0x00000000
0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>;
+
+				/* Inbound 2GB range starting at 0 */
+				dma-ranges = <0x42000000 0x0 0x0 0x0 0x0
0x0 0x80000000>;
+
+				/* This drives busses 10 to 0x1f */
+				bus-range = <0x10 0x1f>;
+
+				/* Legacy interrupts (note the weird
polarity, the bridge seems
+				 * to invert PCIe legacy interrupts).
+				 * We are de-swizzling here because the
numbers are actually for
+				 * port of the root complex virtual P2P
bridge. But I want
+				 * to avoid putting a node for it in the
tree, so the numbers
+				 * below are basically de-swizzled
numbers.
+				 * The real slot is on idsel 0, so the
swizzling is 1:1
+				 */
+				interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+				interrupt-map = <
+					0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /*
swizzled int A */
+					0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /*
swizzled int B */
+					0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /*
swizzled int C */
+					0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /*
swizzled int D */>;
+			};
+
+			PCIE1: pciex at d20000000 {
+				device_type = "pci";
+				#interrupt-cells = <1>;
+				#size-cells = <2>;
+				#address-cells = <3>;
+				compatible = "ibm,plb-pciex-460sx",
"ibm,plb-pciex";
+				primary;
+				port = <0x1>; /* port number */
+				reg = <0x0000000d 0x20000000 0x20000000
/* Config space access */
+				       0x0000000c 0x10001000
0x00001000>;	/* Registers */
+				dcr-reg = <0x120 0x020>;
+				sdr-base = <0x340>;
+
+				/* Outbound ranges, one memory and one
IO,
+				 * later cannot be changed
+				 */
+				ranges = <0x02000000 0x00000000
0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000
+					  0x01000000 0x00000000
0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>;
+
+				/* Inbound 2GB range starting at 0 */
+				dma-ranges = <0x42000000 0x0 0x0 0x0 0x0
0x0 0x80000000>;
+
+				/* This drives busses 10 to 0x1f */
+				bus-range = <0x20 0x2f>;
+
+				/* Legacy interrupts (note the weird
polarity, the bridge seems
+				 * to invert PCIe legacy interrupts).
+				 * We are de-swizzling here because the
numbers are actually for
+				 * port of the root complex virtual P2P
bridge. But I want
+				 * to avoid putting a node for it in the
tree, so the numbers
+				 * below are basically de-swizzled
numbers.
+				 * The real slot is on idsel 0, so the
swizzling is 1:1
+				 */
+				interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+				interrupt-map = <
+					0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /*
swizzled int A */
+					0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /*
swizzled int B */
+					0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /*
swizzled int C */
+					0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /*
swizzled int D */>;
+			};
+
+			PCIE2: pciex at d40000000 {
+				device_type = "pci";
+				#interrupt-cells = <1>;
+				#size-cells = <2>;
+				#address-cells = <3>;
+				compatible = "ibm,plb-pciex-460sx",
"ibm,plb-pciex";
+				primary;
+				port = <0x2>; /* port number */
+				reg = <0x0000000d 0x40000000 0x20000000
/* Config space access */
+				       0x0000000c 0x10002000
0x00001000>;	/* Registers */
+				dcr-reg = <0x140 0x020>;
+				sdr-base = <0x370>;
+
+				/* Outbound ranges, one memory and one
IO,
+				 * later cannot be changed
+				 */
+				ranges = <0x02000000 0x00000000
0x80000000 0x0000000f 0x00000000 0x00000000 0x80000000
+					  0x01000000 0x00000000
0x00000000 0x0000000f 0x80020000 0x00000000 0x00010000>;
+
+				/* Inbound 2GB range starting at 0 */
+				dma-ranges = <0x42000000 0x0 0x0 0x0 0x0
0x0 0x80000000>;
+
+				/* This drives busses 10 to 0x1f */
+				bus-range = <0x30 0x3f>;
+
+				/* Legacy interrupts (note the weird
polarity, the bridge seems
+				 * to invert PCIe legacy interrupts).
+				 * We are de-swizzling here because the
numbers are actually for
+				 * port of the root complex virtual P2P
bridge. But I want
+				 * to avoid putting a node for it in the
tree, so the numbers
+				 * below are basically de-swizzled
numbers.
+				 * The real slot is on idsel 0, so the
swizzling is 1:1
+				 */
+				interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+				interrupt-map = <
+					0x0 0x0 0x0 0x1 &UIC3 0x8 0x4 /*
swizzled int A */
+					0x0 0x0 0x0 0x2 &UIC3 0x9 0x4 /*
swizzled int B */
+					0x0 0x0 0x0 0x3 &UIC3 0xa 0x4 /*
swizzled int C */
+					0x0 0x0 0x0 0x4 &UIC3 0xb 0x4 /*
swizzled int D */>;
+			};
 
 		};
 
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c
b/arch/powerpc/sysdev/ppc4xx_pci.c
index 6ff9d71..64cd020 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.c
+++ b/arch/powerpc/sysdev/ppc4xx_pci.c
@@ -972,6 +972,123 @@ static struct ppc4xx_pciex_hwops
ppc460ex_pcie_hwops __initdata =
 	.setup_utl	= ppc460ex_pciex_init_utl,
 };
 
+static int __init ppc460sx_pciex_core_init(struct device_node *np)
+{
+	/* HSS drive amplitude */
+	mtdcri(SDR0, PESDR0_460SX_HSSL0DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL1DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL2DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL3DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL4DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL5DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL6DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR0_460SX_HSSL7DAMP, 0xB9843211);
+
+	mtdcri(SDR0, PESDR1_460SX_HSSL0DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR1_460SX_HSSL1DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR1_460SX_HSSL2DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR1_460SX_HSSL3DAMP, 0xB9843211);
+
+	mtdcri(SDR0, PESDR2_460SX_HSSL0DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR2_460SX_HSSL1DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR2_460SX_HSSL2DAMP, 0xB9843211);
+	mtdcri(SDR0, PESDR2_460SX_HSSL3DAMP, 0xB9843211);
+
+	/* HSS TX pre-emphasis */
+	mtdcri(SDR0, PESDR0_460SX_HSSL0COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL1COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL2COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL3COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL4COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL5COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL6COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR0_460SX_HSSL7COEFA, 0xDCB98987);
+
+	mtdcri(SDR0, PESDR1_460SX_HSSL0COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR1_460SX_HSSL1COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR1_460SX_HSSL2COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR1_460SX_HSSL3COEFA, 0xDCB98987);
+
+	mtdcri(SDR0, PESDR2_460SX_HSSL0COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR2_460SX_HSSL1COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR2_460SX_HSSL2COEFA, 0xDCB98987);
+	mtdcri(SDR0, PESDR2_460SX_HSSL3COEFA, 0xDCB98987);
+
+	/* HSS TX calibration control */
+	mtdcri(SDR0, PESDR0_460SX_HSSL1CALDRV, 0x22222222);
+	mtdcri(SDR0, PESDR1_460SX_HSSL1CALDRV, 0x22220000);
+	mtdcri(SDR0, PESDR2_460SX_HSSL1CALDRV, 0x22220000);
+
+	/* HSS TX slew control */
+	mtdcri(SDR0, PESDR0_460SX_HSSSLEW, 0xFFFFFFFF);
+	mtdcri(SDR0, PESDR1_460SX_HSSSLEW, 0xFFFF0000);
+	mtdcri(SDR0, PESDR2_460SX_HSSSLEW, 0xFFFF0000);
+
+	udelay(100);
+
+	/* De-assert PLLRESET */
+	dcri_clrset(SDR0, PESDR0_PLLLCT2, 0x00000100, 0);
+
+	/* Reset DL, UTL, GPL before configuration */
+	mtdcri(SDR0, PESDR0_460SX_RCSSET,
+			PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+	mtdcri(SDR0, PESDR1_460SX_RCSSET,
+			PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+	mtdcri(SDR0, PESDR2_460SX_RCSSET,
+			PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+
+	udelay(100);
+
+	/*
+	 * If bifurcation is not enabled, u-boot would have disabled the
+	 * third PCIe port
+	 */
+	if (((mfdcri(SDR0, PESDR1_460SX_HSSCTLSET) & 0x00000001) ==
+				0x00000001)) {
+		printk(KERN_INFO "PCI: PCIE bifurcation setup
successfully.\n");
+		printk(KERN_INFO "PCI: Total 3 PCIE ports are
present\n");
+		return 3;
+	}
+
+	printk(KERN_INFO "PCI: Total 2 PCIE ports are present\n");
+	return 2;
+}
+
+static int ppc460sx_pciex_init_port_hw(struct ppc4xx_pciex_port *port)
+{
+
+	if (port->endpoint)
+		dcri_clrset(SDR0, port->sdr_base + PESDRn_UTLSET2,
+				0x01000000, 0);
+	else
+		dcri_clrset(SDR0, port->sdr_base + PESDRn_UTLSET2,
+				0, 0x01000000);
+
+	/*Gen-1*/
+	mtdcri(SDR0, port->sdr_base + PESDRn_460SX_RCEI, 0x08000000);
+
+	dcri_clrset(SDR0, port->sdr_base + PESDRn_RCSSET,
+			(PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTDL),
+			PESDRx_RCSSET_RSTPYN);
+
+	port->has_ibpre = 1;
+
+	return 0;
+}
+
+static int ppc460sx_pciex_init_utl(struct ppc4xx_pciex_port *port)
+{
+	/* Max 128 Bytes */
+	out_be32 (port->utl_base + PEUTL_PBBSZ,   0x00000000);
+	return 0;
+}
+
+static struct ppc4xx_pciex_hwops ppc460sx_pcie_hwops __initdata = {
+	.core_init	= ppc460sx_pciex_core_init,
+	.port_init_hw	= ppc460sx_pciex_init_port_hw,
+	.setup_utl	= ppc460sx_pciex_init_utl,
+};
+
 #endif /* CONFIG_44x */
 
 #ifdef CONFIG_40x
@@ -1087,6 +1204,8 @@ static int __init
ppc4xx_pciex_check_core_init(struct device_node *np)
 	}
 	if (of_device_is_compatible(np, "ibm,plb-pciex-460ex"))
 		ppc4xx_pciex_hwops = &ppc460ex_pcie_hwops;
+	if (of_device_is_compatible(np, "ibm,plb-pciex-460sx"))
+		ppc4xx_pciex_hwops = &ppc460sx_pcie_hwops;
 #endif /* CONFIG_44x    */
 #ifdef CONFIG_40x
 	if (of_device_is_compatible(np, "ibm,plb-pciex-405ex"))
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.h
b/arch/powerpc/sysdev/ppc4xx_pci.h
index d04e40b..56d9e5d 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.h
+++ b/arch/powerpc/sysdev/ppc4xx_pci.h
@@ -324,6 +324,64 @@
 #define PESDR0_460EX_IHS2		0x036D
 
 /*
+ * 460SX addtional DCRs
+ */
+#define PESDRn_460SX_RCEI		0x02
+
+#define PESDR0_460SX_HSSL0DAMP		0x320
+#define PESDR0_460SX_HSSL1DAMP		0x321
+#define PESDR0_460SX_HSSL2DAMP		0x322
+#define PESDR0_460SX_HSSL3DAMP		0x323
+#define PESDR0_460SX_HSSL4DAMP		0x324
+#define PESDR0_460SX_HSSL5DAMP		0x325
+#define PESDR0_460SX_HSSL6DAMP		0x326
+#define PESDR0_460SX_HSSL7DAMP		0x327
+
+#define PESDR1_460SX_HSSL0DAMP		0x354
+#define PESDR1_460SX_HSSL1DAMP		0x355
+#define PESDR1_460SX_HSSL2DAMP		0x356
+#define PESDR1_460SX_HSSL3DAMP		0x357
+
+#define PESDR2_460SX_HSSL0DAMP		0x384
+#define PESDR2_460SX_HSSL1DAMP		0x385
+#define PESDR2_460SX_HSSL2DAMP		0x386
+#define PESDR2_460SX_HSSL3DAMP		0x387
+
+#define PESDR0_460SX_HSSL0COEFA		0x328
+#define PESDR0_460SX_HSSL1COEFA		0x329
+#define PESDR0_460SX_HSSL2COEFA		0x32A
+#define PESDR0_460SX_HSSL3COEFA		0x32B
+#define PESDR0_460SX_HSSL4COEFA		0x32C
+#define PESDR0_460SX_HSSL5COEFA		0x32D
+#define PESDR0_460SX_HSSL6COEFA		0x32E
+#define PESDR0_460SX_HSSL7COEFA		0x32F
+
+#define PESDR1_460SX_HSSL0COEFA		0x358
+#define PESDR1_460SX_HSSL1COEFA		0x359
+#define PESDR1_460SX_HSSL2COEFA		0x35A
+#define PESDR1_460SX_HSSL3COEFA		0x35B
+
+#define PESDR2_460SX_HSSL0COEFA		0x388
+#define PESDR2_460SX_HSSL1COEFA		0x389
+#define PESDR2_460SX_HSSL2COEFA		0x38A
+#define PESDR2_460SX_HSSL3COEFA		0x38B
+
+#define PESDR0_460SX_HSSL1CALDRV	0x339
+#define PESDR1_460SX_HSSL1CALDRV	0x361
+#define PESDR2_460SX_HSSL1CALDRV	0x391
+
+#define PESDR0_460SX_HSSSLEW		0x338
+#define PESDR1_460SX_HSSSLEW		0x360
+#define PESDR2_460SX_HSSSLEW		0x390
+
+#define PESDR0_460SX_HSSCTLSET		0x31E
+#define PESDR1_460SX_HSSCTLSET		0x352
+#define PESDR2_460SX_HSSCTLSET		0x382
+
+#define PESDR0_460SX_RCSSET		0x304
+#define PESDR1_460SX_RCSSET		0x344
+#define PESDR2_460SX_RCSSET		0x374
+/*
  * Of the above, some are common offsets from the base
  */
 #define PESDRn_UTLSET1			0x00
-- 
1.6.3.3



More information about the Linuxppc-dev mailing list