[PATCH] Adding PCI-E support for 460SX based redwood board.
tmarri at amcc.com
tmarri at amcc.com
Tue Dec 1 09:58:23 EST 2009
From: Tirumala Marri <tmarri at amcc.com>
This patch would add PCI-E support for AMCC 460SX processor based
redwood board.
Signed-off-by: Tirumala Marri <tmarri at amcc.com>
---
arch/powerpc/boot/dts/redwood.dts | 122 +++++++++++++++++++++++++++++++++++++
arch/powerpc/sysdev/ppc4xx_pci.c | 119 ++++++++++++++++++++++++++++++++++++
arch/powerpc/sysdev/ppc4xx_pci.h | 58 +++++++++++++++++
3 files changed, 299 insertions(+), 0 deletions(-)
diff --git a/arch/powerpc/boot/dts/redwood.dts b/arch/powerpc/boot/dts/redwood.dts
index ad402c4..9eeec28 100644
--- a/arch/powerpc/boot/dts/redwood.dts
+++ b/arch/powerpc/boot/dts/redwood.dts
@@ -233,6 +233,128 @@
has-inverted-stacr-oc;
has-new-stacr-staopc;
};
+ PCIE0: pciex at d00000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex";
+ primary;
+ port = <0x0>; /* port number */
+ reg = <0x0000000d 0x00000000 0x20000000 /* Config space access */
+ 0x0000000c 0x10000000 0x00001000>; /* Registers */
+ dcr-reg = <0x100 0x020>;
+ sdr-base = <0x300>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000
+ 0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <0x10 0x1f>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /* swizzled int A */
+ 0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /* swizzled int B */
+ 0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /* swizzled int C */
+ 0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /* swizzled int D */>;
+ };
+
+ PCIE1: pciex at d20000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex";
+ primary;
+ port = <0x1>; /* port number */
+ reg = <0x0000000d 0x20000000 0x20000000 /* Config space access */
+ 0x0000000c 0x10001000 0x00001000>; /* Registers */
+ dcr-reg = <0x120 0x020>;
+ sdr-base = <0x340>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000
+ 0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <0x20 0x2f>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /* swizzled int A */
+ 0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /* swizzled int B */
+ 0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /* swizzled int C */
+ 0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /* swizzled int D */>;
+ };
+
+ PCIE2: pciex at d40000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex";
+ primary;
+ port = <0x2>; /* port number */
+ reg = <0x0000000d 0x40000000 0x20000000 /* Config space access */
+ 0x0000000c 0x10002000 0x00001000>; /* Registers */
+ dcr-reg = <0x140 0x020>;
+ sdr-base = <0x370>;
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x0000000f 0x00000000 0x00000000 0x80000000
+ 0x01000000 0x00000000 0x00000000 0x0000000f 0x80020000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
+
+ /* This drives busses 10 to 0x1f */
+ bus-range = <0x30 0x3f>;
+
+ /* Legacy interrupts (note the weird polarity, the bridge seems
+ * to invert PCIe legacy interrupts).
+ * We are de-swizzling here because the numbers are actually for
+ * port of the root complex virtual P2P bridge. But I want
+ * to avoid putting a node for it in the tree, so the numbers
+ * below are basically de-swizzled numbers.
+ * The real slot is on idsel 0, so the swizzling is 1:1
+ */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <
+ 0x0 0x0 0x0 0x1 &UIC3 0x8 0x4 /* swizzled int A */
+ 0x0 0x0 0x0 0x2 &UIC3 0x9 0x4 /* swizzled int B */
+ 0x0 0x0 0x0 0x3 &UIC3 0xa 0x4 /* swizzled int C */
+ 0x0 0x0 0x0 0x4 &UIC3 0xb 0x4 /* swizzled int D */>;
+ };
};
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.c b/arch/powerpc/sysdev/ppc4xx_pci.c
index 6ff9d71..64cd020 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.c
+++ b/arch/powerpc/sysdev/ppc4xx_pci.c
@@ -972,6 +972,123 @@ static struct ppc4xx_pciex_hwops ppc460ex_pcie_hwops __initdata =
.setup_utl = ppc460ex_pciex_init_utl,
};
+static int __init ppc460sx_pciex_core_init(struct device_node *np)
+{
+ /* HSS drive amplitude */
+ mtdcri(SDR0, PESDR0_460SX_HSSL0DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL1DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL2DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL3DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL4DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL5DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL6DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR0_460SX_HSSL7DAMP, 0xB9843211);
+
+ mtdcri(SDR0, PESDR1_460SX_HSSL0DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR1_460SX_HSSL1DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR1_460SX_HSSL2DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR1_460SX_HSSL3DAMP, 0xB9843211);
+
+ mtdcri(SDR0, PESDR2_460SX_HSSL0DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR2_460SX_HSSL1DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR2_460SX_HSSL2DAMP, 0xB9843211);
+ mtdcri(SDR0, PESDR2_460SX_HSSL3DAMP, 0xB9843211);
+
+ /* HSS TX pre-emphasis */
+ mtdcri(SDR0, PESDR0_460SX_HSSL0COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL1COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL2COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL3COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL4COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL5COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL6COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR0_460SX_HSSL7COEFA, 0xDCB98987);
+
+ mtdcri(SDR0, PESDR1_460SX_HSSL0COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR1_460SX_HSSL1COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR1_460SX_HSSL2COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR1_460SX_HSSL3COEFA, 0xDCB98987);
+
+ mtdcri(SDR0, PESDR2_460SX_HSSL0COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR2_460SX_HSSL1COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR2_460SX_HSSL2COEFA, 0xDCB98987);
+ mtdcri(SDR0, PESDR2_460SX_HSSL3COEFA, 0xDCB98987);
+
+ /* HSS TX calibration control */
+ mtdcri(SDR0, PESDR0_460SX_HSSL1CALDRV, 0x22222222);
+ mtdcri(SDR0, PESDR1_460SX_HSSL1CALDRV, 0x22220000);
+ mtdcri(SDR0, PESDR2_460SX_HSSL1CALDRV, 0x22220000);
+
+ /* HSS TX slew control */
+ mtdcri(SDR0, PESDR0_460SX_HSSSLEW, 0xFFFFFFFF);
+ mtdcri(SDR0, PESDR1_460SX_HSSSLEW, 0xFFFF0000);
+ mtdcri(SDR0, PESDR2_460SX_HSSSLEW, 0xFFFF0000);
+
+ udelay(100);
+
+ /* De-assert PLLRESET */
+ dcri_clrset(SDR0, PESDR0_PLLLCT2, 0x00000100, 0);
+
+ /* Reset DL, UTL, GPL before configuration */
+ mtdcri(SDR0, PESDR0_460SX_RCSSET,
+ PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+ mtdcri(SDR0, PESDR1_460SX_RCSSET,
+ PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+ mtdcri(SDR0, PESDR2_460SX_RCSSET,
+ PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU);
+
+ udelay(100);
+
+ /*
+ * If bifurcation is not enabled, u-boot would have disabled the
+ * third PCIe port
+ */
+ if (((mfdcri(SDR0, PESDR1_460SX_HSSCTLSET) & 0x00000001) ==
+ 0x00000001)) {
+ printk(KERN_INFO "PCI: PCIE bifurcation setup successfully.\n");
+ printk(KERN_INFO "PCI: Total 3 PCIE ports are present\n");
+ return 3;
+ }
+
+ printk(KERN_INFO "PCI: Total 2 PCIE ports are present\n");
+ return 2;
+}
+
+static int ppc460sx_pciex_init_port_hw(struct ppc4xx_pciex_port *port)
+{
+
+ if (port->endpoint)
+ dcri_clrset(SDR0, port->sdr_base + PESDRn_UTLSET2,
+ 0x01000000, 0);
+ else
+ dcri_clrset(SDR0, port->sdr_base + PESDRn_UTLSET2,
+ 0, 0x01000000);
+
+ /*Gen-1*/
+ mtdcri(SDR0, port->sdr_base + PESDRn_460SX_RCEI, 0x08000000);
+
+ dcri_clrset(SDR0, port->sdr_base + PESDRn_RCSSET,
+ (PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTDL),
+ PESDRx_RCSSET_RSTPYN);
+
+ port->has_ibpre = 1;
+
+ return 0;
+}
+
+static int ppc460sx_pciex_init_utl(struct ppc4xx_pciex_port *port)
+{
+ /* Max 128 Bytes */
+ out_be32 (port->utl_base + PEUTL_PBBSZ, 0x00000000);
+ return 0;
+}
+
+static struct ppc4xx_pciex_hwops ppc460sx_pcie_hwops __initdata = {
+ .core_init = ppc460sx_pciex_core_init,
+ .port_init_hw = ppc460sx_pciex_init_port_hw,
+ .setup_utl = ppc460sx_pciex_init_utl,
+};
+
#endif /* CONFIG_44x */
#ifdef CONFIG_40x
@@ -1087,6 +1204,8 @@ static int __init ppc4xx_pciex_check_core_init(struct device_node *np)
}
if (of_device_is_compatible(np, "ibm,plb-pciex-460ex"))
ppc4xx_pciex_hwops = &ppc460ex_pcie_hwops;
+ if (of_device_is_compatible(np, "ibm,plb-pciex-460sx"))
+ ppc4xx_pciex_hwops = &ppc460sx_pcie_hwops;
#endif /* CONFIG_44x */
#ifdef CONFIG_40x
if (of_device_is_compatible(np, "ibm,plb-pciex-405ex"))
diff --git a/arch/powerpc/sysdev/ppc4xx_pci.h b/arch/powerpc/sysdev/ppc4xx_pci.h
index d04e40b..56d9e5d 100644
--- a/arch/powerpc/sysdev/ppc4xx_pci.h
+++ b/arch/powerpc/sysdev/ppc4xx_pci.h
@@ -324,6 +324,64 @@
#define PESDR0_460EX_IHS2 0x036D
/*
+ * 460SX addtional DCRs
+ */
+#define PESDRn_460SX_RCEI 0x02
+
+#define PESDR0_460SX_HSSL0DAMP 0x320
+#define PESDR0_460SX_HSSL1DAMP 0x321
+#define PESDR0_460SX_HSSL2DAMP 0x322
+#define PESDR0_460SX_HSSL3DAMP 0x323
+#define PESDR0_460SX_HSSL4DAMP 0x324
+#define PESDR0_460SX_HSSL5DAMP 0x325
+#define PESDR0_460SX_HSSL6DAMP 0x326
+#define PESDR0_460SX_HSSL7DAMP 0x327
+
+#define PESDR1_460SX_HSSL0DAMP 0x354
+#define PESDR1_460SX_HSSL1DAMP 0x355
+#define PESDR1_460SX_HSSL2DAMP 0x356
+#define PESDR1_460SX_HSSL3DAMP 0x357
+
+#define PESDR2_460SX_HSSL0DAMP 0x384
+#define PESDR2_460SX_HSSL1DAMP 0x385
+#define PESDR2_460SX_HSSL2DAMP 0x386
+#define PESDR2_460SX_HSSL3DAMP 0x387
+
+#define PESDR0_460SX_HSSL0COEFA 0x328
+#define PESDR0_460SX_HSSL1COEFA 0x329
+#define PESDR0_460SX_HSSL2COEFA 0x32A
+#define PESDR0_460SX_HSSL3COEFA 0x32B
+#define PESDR0_460SX_HSSL4COEFA 0x32C
+#define PESDR0_460SX_HSSL5COEFA 0x32D
+#define PESDR0_460SX_HSSL6COEFA 0x32E
+#define PESDR0_460SX_HSSL7COEFA 0x32F
+
+#define PESDR1_460SX_HSSL0COEFA 0x358
+#define PESDR1_460SX_HSSL1COEFA 0x359
+#define PESDR1_460SX_HSSL2COEFA 0x35A
+#define PESDR1_460SX_HSSL3COEFA 0x35B
+
+#define PESDR2_460SX_HSSL0COEFA 0x388
+#define PESDR2_460SX_HSSL1COEFA 0x389
+#define PESDR2_460SX_HSSL2COEFA 0x38A
+#define PESDR2_460SX_HSSL3COEFA 0x38B
+
+#define PESDR0_460SX_HSSL1CALDRV 0x339
+#define PESDR1_460SX_HSSL1CALDRV 0x361
+#define PESDR2_460SX_HSSL1CALDRV 0x391
+
+#define PESDR0_460SX_HSSSLEW 0x338
+#define PESDR1_460SX_HSSSLEW 0x360
+#define PESDR2_460SX_HSSSLEW 0x390
+
+#define PESDR0_460SX_HSSCTLSET 0x31E
+#define PESDR1_460SX_HSSCTLSET 0x352
+#define PESDR2_460SX_HSSCTLSET 0x382
+
+#define PESDR0_460SX_RCSSET 0x304
+#define PESDR1_460SX_RCSSET 0x344
+#define PESDR2_460SX_RCSSET 0x374
+/*
* Of the above, some are common offsets from the base
*/
#define PESDRn_UTLSET1 0x00
--
1.6.3.3
More information about the Linuxppc-dev
mailing list