[U-Boot] NAND ECC Error with wrong SMC ording bug

Sean MacLennan smaclennan at pikatech.com
Fri Aug 21 05:36:44 EST 2009


On Thu, 20 Aug 2009 07:01:21 +0200
Stefan Roese <sr at denx.de> wrote:

> On Thursday 20 August 2009 06:38:51 Sean MacLennan wrote:
> > > I see other boards using SMC as well, can someone comment on the
> > > change I am proposing.
> > > Should I change the correction algorithm or the calculate
> > > function? If the later is preferred
> > > it would mean the change must be pushed in both U-Boot and Linux.
> >
> > Odds are the calculate function is wrong. The correction algo is
> > used by many nand drivers, I *assume* it is correct. The calculate
> > function was set to agree with u-boot (1.3.0).
> 
> Yes, it seems that you changed the order in the calculation function
> while reworking the NDFC driver for arch/powerpc. So we should
> probably change this order back to the original version. And change
> it in U-Boot as well.
> 
> BTW: I didn't see any problems with ECC so far with the current code.
> Feng, how did you spot this problem?

Ok, I think I have reproduced the problem programmatically. Basically,
I force a one bit error with the following patch:

diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 8c21b89..91dd5b4 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -1628,11 +1628,22 @@ static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
 	uint8_t *ecc_calc = chip->buffers->ecccalc;
 	const uint8_t *p = buf;
 	uint32_t *eccpos = chip->ecc.layout->eccpos;
+	static int count;
 
 	for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
 		chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
-		chip->write_buf(mtd, p, eccsize);
-		chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+		if (count == 0) {
+			count = 1;
+			printk("Corrupt one bit: %08x => %08x\n",
+			       *p, *p ^ 8);
+			*(uint8_t *)p ^= 8;
+			chip->write_buf(mtd, p, eccsize);
+			*(uint8_t *)p ^= 8;
+			nand_calculate_ecc(mtd, p, &ecc_calc[i]);
+		} else {
+			chip->write_buf(mtd, p, eccsize);
+			chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+		}
 	}
 
 	for (i = 0; i < chip->ecc.total; i++)

Basically I write a one bit error to the NAND, but calculate with the
correct bit. This assumes nand_calculate_ecc is correct.

I then added debugs to the correction to make sure it corrected
properly:

diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/nand_ecc.c
index c0cb87d..57dcaa1 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/nand_ecc.c
@@ -483,14 +483,20 @@ int nand_correct_data(struct mtd_info *mtd, unsigned char *buf,
 			byte_addr = (addressbits[b2 & 0x3] << 8) +
 				    (addressbits[b1] << 4) + addressbits[b0];
 		bit_addr = addressbits[b2 >> 2];
+
+		printk("Single bit error: correct %08x => %08x\n",
+		       buf[byte_addr], buf[byte_addr] ^ (1 << bit_addr));
+
 		/* flip the bit */
 		buf[byte_addr] ^= (1 << bit_addr);
 		return 1;
 
 	}
 	/* count nr of bits; use table lookup, faster than calculating it */
-	if ((bitsperbyte[b0] + bitsperbyte[b1] + bitsperbyte[b2]) == 1)
+	if ((bitsperbyte[b0] + bitsperbyte[b1] + bitsperbyte[b2]) == 1) {
+		printk("ECC DATA BAD\n"); // SAM DBG
 		return 1;	/* error in ecc data; no action needed */
+	}
 
 	printk(KERN_ERR "uncorrectable error : ");
 	return -1;

With the current ndfc code, the error correction gets the bits wrong.
Switching it back to the original way and the correction is correct.

diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/ndfc.c
index 89bf85a..497e175 100644
--- a/drivers/mtd/nand/ndfc.c
+++ b/drivers/mtd/nand/ndfc.c
@@ -101,9 +101,8 @@ static int ndfc_calculate_ecc(struct mtd_info *mtd,
 
 	wmb();
 	ecc = in_be32(ndfc->ndfcbase + NDFC_ECC);
-	/* The NDFC uses Smart Media (SMC) bytes order */
-	ecc_code[0] = p[2];
-	ecc_code[1] = p[1];
+	ecc_code[0] = p[1];
+	ecc_code[1] = p[2];
 	ecc_code[2] = p[3];
 
 	return 0;

Does anybody see a problem with my method of reproducing the bug? This
bug is deadly for our customers. I don't want to make the change unless
it is absolutely necessary.

Cheers,
   Sean


More information about the Linuxppc-dev mailing list