Problems with PCI-E devices not being detected with switch
Ayman El-Khashab
AymanE at tanisys.com
Tue Oct 21 08:03:43 EST 2008
Thank you Ben, I've had success with the patch, details below ...
Benjamin Herrenschmidt wrote:
> Can you try this (untested) patch and send me the resulting dmesg log
> (along with whether it helps).
>
> Index: linux-work/drivers/pci/probe.c
> ===================================================================
> --- linux-work.orig/drivers/pci/probe.c 2008-10-18 08:10:25.000000000
> +1100 +++ linux-work/drivers/pci/probe.c 2008-10-18
> 08:14:14.000000000 +1100 @@ -536,19 +536,27 @@
> int is_cardbus = (dev->hdr_type == PCI_HEADER_TYPE_CARDBUS);
> u32 buses, i, j = 0;
> u16 bctl;
> + int broken = 0;
>
> pci_read_config_dword(dev, PCI_PRIMARY_BUS, &buses);
>
> dev_dbg(&dev->dev, "scanning behind bridge, config %06x, pass %d\n",
> buses & 0xffffff, pass);
>
> + /* Check if setup is sensible at all */
> + if ((buses & 0xff) != bus->number ||
> + ((buses >> 8) & 0xff) != <= bus->number) {
Note that I removed the <= from the above line -- I did not think it was
correct. Please let me know if that was wrong.
<snipped rest of patch>
Attached below is the dmesg output, in this case the SIL on the downstream
switch port was detected correctly. Advise if there is something else that
needs to be tried.
Thanks
Ayman
Kernel command line: ramdisk_size=65536 root=/dev/ram rw ip=169.254.0.199:169.20
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
UIC3 (32 IRQ sources) at DCR 0xf0
PID hash table entries: 2048 (order: 11, 8192 bytes)
time_init: decrementer frequency = 800.000010 MHz
time_init: processor frequency = 800.000010 MHz
clocksource: timebase mult[500000] shift[22] registered
clockevent: decrementer mult[cccc] shift[16] cpu[0]
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
High memory: 0k
Memory: 512640k/524288k available (3244k kernel code, 11336k reserved, 124k dat)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1597.44 BogoMIPS (lpj=3194880)
Mount-cache hash table entries: 512
net_namespace: 288 bytes
NET: Registered protocol family 16
256k L2-cache enabled
PCIE0: Checking link...
PCIE0: No device detected.
PCI host bridge /plb/pciex at d00000000 (primary) ranges:
MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000
IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCIE0: successfully set as endpoint
PCIE1: Checking link...
PCIE1: Device detected, waiting for link...
PCIE1: link is up !
PCI host bridge /plb/pciex at d20000000 (primary) ranges:
MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCIE1: successfully set as root-complex
PCI host bridge /plb/pci at c0ec00000 (primary) ranges:
MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000
IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCI: Probing PCI hardware
PCI: Scanning bus 0000:40
pci 0000:40:00.0: found [eee0/fed0] class 000b20 header type 00
PCI: 0000:40:00.0 reg 10 64bit mmio: [0, 1ffffff]
PCI: Hiding 4xx host bridge resources 0000:40:00.0
PCI: Fixups for bus 0000:40
PCI: Bus scan for 0000:40 returning with max=40
PCI: Scanning bus 0001:80
pci 0001:80:00.0: found [aaa1/bed1] class 000604 header type 01
PCI: 0001:80:00.0 reg 10 32bit mmio: [0, 7fffffff]
PCI: Hiding 4xx host bridge resources 0001:80:00.0
PCI: Fixups for bus 0001:80
pci 0001:80:00.0: scanning behind bridge, config bf8180, pass 0
pci 0001:80:00.0: bus configuration doesn't match, reconfiguring
pci 0001:80:00.0: scanning behind bridge, config 000000, pass 1
pci 0001:80:00.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:81
pci 0001:81:00.0: found [10b5/8509] class 000604 header type 01
PCI: 0001:81:00.0 reg 10 32bit mmio: [b8000000, b801ffff]
pci 0001:81:00.0: PME# supported from D0 D3hot D3cold
pci 0001:81:00.0: PME# disabled
PCI: Fixups for bus 0001:81
PCI: bridge 0001:80:00.0 io port: [0, fff]
PCI: bridge 0001:80:00.0 32bit mmio: [b8000000, b81fffff]
pci 0001:81:00.0: scanning behind bridge, config 060201, pass 0
pci 0001:81:00.0: bus configuration doesn't match, reconfiguring
pci 0001:81:00.0: scanning behind bridge, config 000000, pass 1
pci 0001:81:00.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:82
pci 0001:82:01.0: found [10b5/8509] class 000604 header type 01
pci 0001:82:01.0: PME# supported from D0 D3hot D3cold
pci 0001:82:01.0: PME# disabled
pci 0001:82:02.0: found [10b5/8509] class 000604 header type 01
pci 0001:82:02.0: PME# supported from D0 D3hot D3cold
pci 0001:82:02.0: PME# disabled
pci 0001:82:03.0: found [10b5/8509] class 000604 header type 01
pci 0001:82:03.0: PME# supported from D0 D3hot D3cold
pci 0001:82:03.0: PME# disabled
pci 0001:82:04.0: found [10b5/8509] class 000604 header type 01
pci 0001:82:04.0: PME# supported from D0 D3hot D3cold
pci 0001:82:04.0: PME# disabled
PCI: Fixups for bus 0001:82
PCI: bridge 0001:81:00.0 32bit mmio: [b8100000, b81fffff]
pci 0001:82:01.0: scanning behind bridge, config 030302, pass 0
pci 0001:82:01.0: bus configuration doesn't match, reconfiguring
pci 0001:82:02.0: scanning behind bridge, config 040402, pass 0
pci 0001:82:02.0: bus configuration doesn't match, reconfiguring
pci 0001:82:03.0: scanning behind bridge, config 050502, pass 0
pci 0001:82:03.0: bus configuration doesn't match, reconfiguring
pci 0001:82:04.0: scanning behind bridge, config 060602, pass 0
pci 0001:82:04.0: bus configuration doesn't match, reconfiguring
pci 0001:82:01.0: scanning behind bridge, config 000000, pass 1
pci 0001:82:01.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:83
PCI: Fixups for bus 0001:83
PCI: Bus scan for 0001:83 returning with max=83
pci 0001:82:02.0: scanning behind bridge, config 000000, pass 1
pci 0001:82:02.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:84
PCI: Fixups for bus 0001:84
PCI: Bus scan for 0001:84 returning with max=84
pci 0001:82:03.0: scanning behind bridge, config 000000, pass 1
pci 0001:82:03.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:85
pci 0001:85:00.0: found [1095/3531] class 000180 header type 00
PCI: 0001:85:00.0 reg 10 64bit mmio: [b8100000, b810007f]
PCI: 0001:85:00.0 reg 18 64bit mmio: [b8102000, b8103fff]
PCI: 0001:85:00.0 reg 20 io port: [ffffff80, ffffffff]
pci 0001:85:00.0: supports D1
pci 0001:85:00.0: supports D2
PCI: Fixups for bus 0001:85
PCI: bridge 0001:82:03.0 32bit mmio: [b8100000, b81fffff]
PCI: Bus scan for 0001:85 returning with max=85
pci 0001:82:04.0: scanning behind bridge, config 000000, pass 1
pci 0001:82:04.0: bus configuration doesn't match, reconfiguring
PCI: Scanning bus 0001:86
PCI: Fixups for bus 0001:86
PCI: Bus scan for 0001:86 returning with max=86
PCI: Bus scan for 0001:82 returning with max=86
PCI: Bus scan for 0001:81 returning with max=86
PCI: Bus scan for 0001:80 returning with max=86
PCI: Scanning bus 0002:00
PCI: Fixups for bus 0002:00
PCI: Bus scan for 0002:00 returning with max=00
pci 0001:82:01.0: PCI bridge, secondary bus 0001:83
pci 0001:82:01.0: IO window: disabled
pci 0001:82:01.0: MEM window: disabled
pci 0001:82:01.0: PREFETCH window: disabled
pci 0001:82:02.0: PCI bridge, secondary bus 0001:84
pci 0001:82:02.0: IO window: disabled
pci 0001:82:02.0: MEM window: disabled
pci 0001:82:02.0: PREFETCH window: disabled
pci 0001:82:03.0: PCI bridge, secondary bus 0001:85
pci 0001:82:03.0: IO window: 0x00-0xfff
pci 0001:82:03.0: MEM window: 0x80000000-0x800fffff
pci 0001:82:03.0: PREFETCH window: disabled
pci 0001:82:04.0: PCI bridge, secondary bus 0001:86
pci 0001:82:04.0: IO window: disabled
pci 0001:82:04.0: MEM window: disabled
pci 0001:82:04.0: PREFETCH window: disabled
pci 0001:81:00.0: PCI bridge, secondary bus 0001:82
pci 0001:81:00.0: IO window: 0x00-0xfff
pci 0001:81:00.0: MEM window: 0x80000000-0x800fffff
pci 0001:81:00.0: PREFETCH window: disabled
pci 0001:80:00.0: PCI bridge, secondary bus 0001:81
pci 0001:80:00.0: IO window: 0x00-0xfff
pci 0001:80:00.0: MEM window: 0x80000000-0x801fffff
pci 0001:80:00.0: PREFETCH window: disabled
pci 0001:81:00.0: enabling device (0006 -> 0007)
pci 0001:82:03.0: enabling device (0006 -> 0007)
bus: 40 index 0 io port: [fffc0000, fffcffff]
bus: 40 index 1 mmio: [e00000000, e7fffffff]
bus: 80 index 0 io port: [fffe0000, fffeffff]
bus: 80 index 1 mmio: [e80000000, effffffff]
bus: 81 index 0 io port: [fffe0000, fffe0fff]
bus: 81 index 1 mmio: [e80000000, e801fffff]
bus: 81 index 2 mmio: [0, 0]
bus: 81 index 3 mmio: [0, 0]
bus: 82 index 0 io port: [fffe0000, fffe0fff]
bus: 82 index 1 mmio: [e80000000, e800fffff]
bus: 82 index 2 mmio: [0, 0]
bus: 82 index 3 mmio: [0, 0]
bus: 83 index 0 mmio: [0, 0]
bus: 83 index 1 mmio: [0, 0]
bus: 83 index 2 mmio: [0, 0]
bus: 83 index 3 mmio: [0, 0]
bus: 84 index 0 mmio: [0, 0]
bus: 84 index 1 mmio: [0, 0]
bus: 84 index 2 mmio: [0, 0]
bus: 84 index 3 mmio: [0, 0]
bus: 85 index 0 io port: [fffe0000, fffe0fff]
bus: 85 index 1 mmio: [e80000000, e800fffff]
bus: 85 index 2 mmio: [0, 0]
bus: 85 index 3 mmio: [0, 0]
bus: 86 index 0 mmio: [0, 0]
bus: 86 index 1 mmio: [0, 0]
bus: 86 index 2 mmio: [0, 0]
bus: 86 index 3 mmio: [0, 0]
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [d80000000, dffffffff]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 3242k freed
SATA port disabled via device-tree
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1008
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport-driver 0001:80:00.0: found MSI capability
pci_express 0001:80:00.0:pcie00: allocate port service
pci_express 0001:80:00.0:pcie01: allocate port service
pcieport-driver 0001:81:00.0: found MSI capability
pcieport-driver 0001:82:01.0: found MSI capability
pci_express 0001:82:01.0:pcie22: allocate port service
pcieport-driver 0001:82:02.0: found MSI capability
pci_express 0001:82:02.0:pcie22: allocate port service
pcieport-driver 0001:82:03.0: found MSI capability
pci_express 0001:82:03.0:pcie22: allocate port service
pcieport-driver 0001:82:04.0: found MSI capability
aer 0001:80:00.0:pcie01: request IRQ failed
aer: probe of 0001:80:00.0:pcie01 failed with error -38
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: HPC vendor_id 10b5 device_id 8509 ss_vid 0 ss_did 0
hpdriver 0001:82:01.0:pcie22: service driver hpdriver loaded
pciehp: HPC vendor_id 10b5 device_id 8509 ss_vid 0 ss_did 0
hpdriver 0001:82:02.0:pcie22: service driver hpdriver loaded
pciehp: HPC vendor_id 10b5 device_id 8509 ss_vid 0 ss_did 0
hpdriver 0001:82:03.0:pcie22: service driver hpdriver loaded
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
fakephp: Fake PCI Hot Plug Controller Driver
fakephp: pci_hp_register failed with error -16
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 22) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 24) is a 16550A
serial8250.0: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
serial8250.0: ttyS3 at MMIO 0x4ef600600 (irq = 25) is a 16550A
4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 22) is a 16550A
4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 24) is a 16550A
4ef600500.serial: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
4ef600600.serial: ttyS3 at MMIO 0x4ef600600 (irq = 25) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
ZMII /plb/opb/emac-zmii at ef600d00 initialized
RGMII /plb/opb/emac-rgmii at ef601500 initialized with MDIO support
TAH /plb/opb/emac-tah at ef601350 initialized
TAH /plb/opb/emac-tah at ef601450 initialized
/plb/opb/emac-rgmii at ef601500: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet at ef600e00, MAC 00:10:ec:01:02:b9
eth0: found Generic MII PHY (0x00)
/plb/opb/emac-rgmii at ef601500: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet at ef600f00, MAC 00:10:ec:81:02:b9
eth1: found Generic MII PHY (0x01)
Driver 'sd' needs updating - please use bus_type methods
sata_sil24 0001:85:00.0: version 1.1
sata_sil24 0001:85:00.0: enabling device (0006 -> 0007)
scsi0 : sata_sil24
ata1: SATA max UDMA/100 host m128 at 0xe80002000 port 0xe80000000 irq 21
ata1: SATA link down (SStatus 0 SControl 0)
4cc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
4cc000000.nor_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Creating 7 MTD partitions on "4cc000000.nor_flash":
0x00000000-0x001e0000 : "kernel"
0x001e0000-0x00200000 : "dtb"
0x00200000-0x01600000 : "ramdisk"
0x01600000-0x01a00000 : "jffs2"
0x01a00000-0x03f60000 : "user"
0x03f60000-0x03fa0000 : "env"
0x03fa0000-0x04000000 : "u-boot"
NDFC NAND Driver initialized. Chip-Rev: 0x00000111
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-)
Scanning device for bad blocks
Bad eraseblock 764 at 0x05f80000
Number of partitions 3
Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00100000 : "u-boot"
0x00100000-0x00140000 : "env"
0x00140000-0x08000000 : "content"
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ppc-of-ohci 4bffd0000.usb: OF OHCI
ppc-of-ohci 4bffd0000.usb: new USB bus registered, assigned bus number 1
ppc-of-ohci 4bffd0000.usb: irq 40, io mem 0x4bffd0000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OF OHCI
usb usb1: Manufacturer: Linux 2.6.27-01160-gc08fd34-dirty ohci_hcd
usb usb1: SerialNumber: PPC-OF USB
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
dwc_otg: version 2.60a 22-NOV-2006
dwc_otg: Shared Tx FIFO mode
dwc_otg: Using Slave mode
dwc_otg dwc_otg.0: DWC OTG Controller
dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 2
dwc_otg dwc_otg.0: irq 28, io mem 0x00000000
dwc_otg: dwc_otg_core_host_init: Unable to clear halt on channel 1
dwc_otg: Init: Port Power? op_state=4
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: DWC OTG Controller
usb usb2: Manufacturer: Linux 2.6.27-01160-gc08fd34-dirty dwc_otg_hcd
usb usb2: SerialNumber: dwc_otg.0
i2c /dev entries driver
ibm-iic 4ef600700.i2c: clckdiv = 9
rtc-m41t80 0-0068: chip found, driver version 0.05
rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0
ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
ibm-iic 4ef600800.i2c: clckdiv = 9
ibm-iic 4ef600800.i2c: using standard (100 kHz) mode
24c01a EEPROM driver initialized
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-m41t80 0-0068: setting system clock to 2008-10-20 17:08:34 UTC (1224522514)
eth0: link is up, 100 FDX, pause enabled
IP-Config: Complete:
device=eth0, addr=169.254.0.199, mask=255.255.255.0, gw=169.254.0.100,
host=tanosx, domain=, nis-domain=(none),
bootserver=169.254.0.100, rootserver=169.254.0.100, rootpath=
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 160k init
#
More information about the Linuxppc-dev
mailing list