[i2c] [PATCH6/7] i2c: adds support for i2c bus on Freescale CPM1/CPM2 controllers
Wolfram Sang
w.sang at pengutronix.de
Tue May 6 23:51:13 EST 2008
Hi Jochen,
I just had a debug session with a MPC8260 + eeprom and got some
questions:
> This driver uses the port of 2.4 code from Vitaly Bordug
> <vitb at kernel.crashing.org> and the actual algorithm used by the i2c
> driver of the DBox code on cvs.tuxboc.org from Felix Domke
> (tmbinc at gmx.net) and Gillem (htoa at gmx.net) converted to an
> of_platform_driver. Tested on CPM1 (MPC823 on dbox2 hardware) and
> CPM2 (MPC8272).
>
> Signed-off-by: Jochen Friedrich <jochen at scram.de>
> ---
> drivers/i2c/busses/Kconfig | 10 +
> drivers/i2c/busses/Makefile | 1 +
> drivers/i2c/busses/i2c-cpm.c | 728 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 739 insertions(+), 0 deletions(-)
> create mode 100644 drivers/i2c/busses/i2c-cpm.c
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 5fa9c3c..5c4f270 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -114,6 +114,16 @@ config I2C_BLACKFIN_TWI_CLK_KHZ
> help
> The unit of the TWI clock is kHz.
>
> +config I2C_CPM
> + tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)"
> + depends on (CPM1 || CPM2) && PPC_OF
> + help
> + This supports the use of the I2C interface on Freescale
> + processors with CPM1 or CPM2.
> +
> + This driver can also be built as a module. If so, the module
> + will be called i2c-cpm.
> +
> config I2C_DAVINCI
> tristate "DaVinci I2C driver"
> depends on ARCH_DAVINCI
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index ea7068f..1291e2b 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -11,6 +11,7 @@ obj-$(CONFIG_I2C_AMD8111) += i2c-amd8111.o
> obj-$(CONFIG_I2C_AT91) += i2c-at91.o
> obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o
> obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o
> +obj-$(CONFIG_I2C_CPM) += i2c-cpm.o
> obj-$(CONFIG_I2C_DAVINCI) += i2c-davinci.o
> obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o
> obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o
> diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c
> new file mode 100644
> index 0000000..e6e8317
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-cpm.c
> @@ -0,0 +1,728 @@
> +/*
> + * Freescale CPM1/CPM2 I2C interface.
> + * Copyright (c) 1999 Dan Malek (dmalek at jlc.net).
> + *
> + * moved into proper i2c interface;
> + * Brad Parker (brad at heeltoe.com)
> + *
> + * (C) 2007 Montavista Software, Inc.
> + * Vitaly Bordug <vitb at kernel.crashing.org>
> + *
> + * Parts from dbox2_i2c.c (cvs.tuxbox.org)
> + * (C) 2000-2001 Felix Domke (tmbinc at gmx.net), Gillem (htoa at gmx.net)
> + *
> + * Converted to of_platform_device. Renamed to i2c-cpm.c.
> + * (C) 2007,2008 Jochen Friedrich <jochen at scram.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +#include <linux/slab.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/errno.h>
> +#include <linux/stddef.h>
> +#include <linux/i2c.h>
> +#include <linux/io.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/of_device.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_i2c.h>
> +#include <sysdev/fsl_soc.h>
> +#include <asm/cpm.h>
> +
> +/* Try to define this if you have an older CPU (earlier than rev D4) */
> +/* However, better use a GPIO based bitbang driver in this case :/ */
> +#undef I2C_CHIP_ERRATA
> +
> +#define CPM_MAX_READ 513
> +#define CPM_MAXBD 4
> +
> +#define CPM_CR_INIT_TRX (0x00)
> +#define CPM_CR_CLOSE_RX_BD (0x07)
> +
> +#define I2C_EB (0x10) /* Big endian mode */
> +#define I2C_EB_CPM2 (0x30) /* Big endian mode, memory snoop */
> +
> +#define DPRAM_BASE ((u8 __iomem __force *)cpm_muram_addr(0))
> +
> +/* I2C parameter RAM. */
> +struct i2c_ram {
> + ushort rbase; /* Rx Buffer descriptor base address */
> + ushort tbase; /* Tx Buffer descriptor base address */
> + u_char rfcr; /* Rx function code */
> + u_char tfcr; /* Tx function code */
> + ushort mrblr; /* Max receive buffer length */
> + uint rstate; /* Internal */
> + uint rdp; /* Internal */
> + ushort rbptr; /* Rx Buffer descriptor pointer */
> + ushort rbc; /* Internal */
> + uint rxtmp; /* Internal */
> + uint tstate; /* Internal */
> + uint tdp; /* Internal */
> + ushort tbptr; /* Tx Buffer descriptor pointer */
> + ushort tbc; /* Internal */
> + uint txtmp; /* Internal */
> + char res1[4]; /* Reserved */
> + ushort rpbase; /* Relocation pointer */
> + char res2[2]; /* Reserved */
> +};
> +
> +/* I2C Registers */
> +struct i2c_reg {
> + u8 i2mod;
> + u8 res1[3];
> + u8 i2add;
> + u8 res2[3];
> + u8 i2brg;
> + u8 res3[3];
> + u8 i2com;
> + u8 res4[3];
> + u8 i2cer;
> + u8 res5[3];
> + u8 i2cmr;
> +};
> +
> +struct cpm_i2c {
> + char *base;
> + struct of_device *ofdev;
> + struct i2c_adapter adap;
> + uint dp_addr;
> + int version; /* CPM1=1, CPM2=2 */
> + int irq;
> + int cp_command;
> + struct i2c_reg __iomem *i2c_reg;
> + struct i2c_ram __iomem *i2c_ram;
> + u16 i2c_addr;
> + wait_queue_head_t i2c_wait;
> + struct mutex i2c_mutex; /* Protects struct i2c_ram */
> + cbd_t __iomem *tbase;
> + cbd_t __iomem *rbase;
> + u_char *txbuf[CPM_MAXBD];
> + u_char *rxbuf[CPM_MAXBD];
> + u32 txdma[CPM_MAXBD];
> + u32 rxdma[CPM_MAXBD];
> +};
> +
> +static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id)
> +{
> + struct cpm_i2c *cpm;
> + struct i2c_reg __iomem *i2c_reg;
> + struct i2c_adapter *adap = dev_id;
> + int i;
> +
> + cpm = i2c_get_adapdata(dev_id);
> + i2c_reg = cpm->i2c_reg;
> +
> + /* Clear interrupt. */
> + i = in_8(&i2c_reg->i2cer);
> + out_8(&i2c_reg->i2cer, i);
> +
> + dev_dbg(&adap->dev, "Interrupt: %x\n", i);
> +
> + /* Get me going again. */
> + wake_up_interruptible(&cpm->i2c_wait);
> +
> + return i ? IRQ_HANDLED : IRQ_NONE;
> +}
> +
> +static void cpm_reset_i2c_params(struct cpm_i2c *cpm)
> +{
> + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
> +
> + /* Set up the IIC parameters in the parameter ram. */
> + out_be16(&i2c_ram->tbase, (u8 __iomem *)cpm->tbase - DPRAM_BASE);
> + out_be16(&i2c_ram->rbase, (u8 __iomem *)cpm->rbase - DPRAM_BASE);
> +
> + if (cpm->version == 1) {
> + out_8(&i2c_ram->tfcr, I2C_EB);
> + out_8(&i2c_ram->rfcr, I2C_EB);
> + } else {
> + out_8(&i2c_ram->tfcr, I2C_EB_CPM2);
> + out_8(&i2c_ram->rfcr, I2C_EB_CPM2);
> + }
> +
> + out_be16(&i2c_ram->mrblr, CPM_MAX_READ);
> +
> + out_be32(&i2c_ram->rstate, 0);
> + out_be32(&i2c_ram->rdp, 0);
> + out_be16(&i2c_ram->rbptr, 0);
> + out_be16(&i2c_ram->rbc, 0);
> + out_be32(&i2c_ram->rxtmp, 0);
> + out_be32(&i2c_ram->tstate, 0);
> + out_be32(&i2c_ram->tdp, 0);
> + out_be16(&i2c_ram->tbptr, 0);
> + out_be16(&i2c_ram->tbc, 0);
> + out_be32(&i2c_ram->txtmp, 0);
> +}
> +
> +static void cpm_i2c_force_close(struct i2c_adapter *adap)
> +{
> + struct cpm_i2c *cpm = i2c_get_adapdata(adap);
> + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
> +
> + dev_dbg(&adap->dev, "cpm_i2c_force_close()\n");
> +
> + cpm_command(cpm->cp_command, CPM_CR_CLOSE_RX_BD);
> +
> + out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */
> + out_8(&i2c_reg->i2cer, 0xff);
> +}
> +
> +static void cpm_i2c_parse_message(struct i2c_adapter *adap,
> + struct i2c_msg *pmsg, int num, int tx, int rx)
> +{
> + cbd_t __iomem *tbdf;
> + cbd_t __iomem *rbdf;
> + u_char addr;
> + u_char *tb;
> + u_char *rb;
> + struct cpm_i2c *cpm = i2c_get_adapdata(adap);
> +
> + tbdf = cpm->tbase + tx;
> + rbdf = cpm->rbase + rx;
> +
> + addr = pmsg->addr << 1;
> + if (pmsg->flags & I2C_M_RD)
> + addr |= 1;
> +
> + tb = cpm->txbuf[tx];
> + rb = cpm->rxbuf[rx];
> +
> + /* Align read buffer */
> + rb = (u_char *) (((ulong) rb + 1) & ~1);
> +
> + tb[0] = addr; /* Device address byte w/rw flag */
> +
> + out_be16(&tbdf->cbd_datlen, pmsg->len + 1);
> + out_be16(&tbdf->cbd_sc, 0);
> +
> + if (!(pmsg->flags & I2C_M_NOSTART))
> + setbits16(&tbdf->cbd_sc, BD_I2C_START);
> +
> + if (tx + 1 == num)
> + setbits16(&tbdf->cbd_sc, BD_SC_LAST | BD_SC_WRAP);
> +
> + if (pmsg->flags & I2C_M_RD) {
> + /*
> + * To read, we need an empty buffer of the proper length.
> + * All that is used is the first byte for address, the remainder
> + * is just used for timing (and doesn't really have to exist).
> + */
> +
> + dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr);
> +
> + out_be16(&rbdf->cbd_datlen, 0);
> + out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT);
> +
> + if (rx + 1 == CPM_MAXBD)
> + setbits16(&rbdf->cbd_sc, BD_SC_WRAP);
> +
> + eieio();
> + setbits16(&tbdf->cbd_sc, BD_SC_READY);
> + } else {
> + dev_dbg(&adap->dev, "cpm_iic_write(abyte=0x%x)\n", addr);
> +
> + memcpy(tb+1, pmsg->buf, pmsg->len);
> +
> + eieio();
> + setbits16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_INTRPT);
> + }
> +}
> +
> +static int cpm_i2c_check_message(struct i2c_adapter *adap,
> + struct i2c_msg *pmsg, int tx, int rx)
> +{
> + cbd_t __iomem *tbdf;
> + cbd_t __iomem *rbdf;
> + u_char *tb;
> + u_char *rb;
> + struct cpm_i2c *cpm = i2c_get_adapdata(adap);
> +
> + tbdf = cpm->tbase + tx;
> + rbdf = cpm->rbase + rx;
> +
> + tb = cpm->txbuf[tx];
> + rb = cpm->rxbuf[rx];
> +
> + /* Align read buffer */
> + rb = (u_char *) (((uint) rb + 1) & ~1);
> +
> + eieio();
> + if (pmsg->flags & I2C_M_RD) {
> + dev_dbg(&adap->dev, "tx sc 0x%04x, rx sc 0x%04x\n",
> + in_be16(&tbdf->cbd_sc), in_be16(&rbdf->cbd_sc));
> +
> + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) {
> + dev_err(&adap->dev, "IIC read; No ack\n");
> + return -EIO;
> + }
> + if (in_be16(&rbdf->cbd_sc) & BD_SC_EMPTY) {
> + dev_err(&adap->dev,
> + "IIC read; complete but rbuf empty\n");
> + return -EREMOTEIO;
> + }
> + if (in_be16(&rbdf->cbd_sc) & BD_SC_OV) {
> + dev_err(&adap->dev, "IIC read; Overrun\n");
> + return -EREMOTEIO;
> + }
> + memcpy(pmsg->buf, rb, pmsg->len);
> + } else {
> + dev_dbg(&adap->dev, "tx sc %d 0x%04x\n", tx,
> + in_be16(&tbdf->cbd_sc));
> +
> + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) {
> + dev_err(&adap->dev, "IIC write; No ack\n");
> + return -EIO;
> + }
> + if (in_be16(&tbdf->cbd_sc) & BD_SC_UN) {
> + dev_err(&adap->dev, "IIC write; Underrun\n");
> + return -EIO;
> + }
> + if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) {
> + dev_err(&adap->dev, "IIC write; Collision\n");
> + return -EIO;
> + }
> + }
> + return 0;
> +}
> +
> +static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
> +{
> + struct cpm_i2c *cpm = i2c_get_adapdata(adap);
> + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg;
> + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram;
> + struct i2c_msg *pmsg;
> + int ret, i;
> + int tptr;
> + int rptr;
> + cbd_t __iomem *tbdf;
> + cbd_t __iomem *rbdf;
> +
> + if (num > CPM_MAXBD)
> + return -EINVAL;
> +
> + /* Check if we have any oversized READ requests */
> + for (i = 0; i < num; i++) {
> + pmsg = &msgs[i];
> + if (pmsg->len >= CPM_MAX_READ)
> + return -EINVAL;
> + }
> +
> + mutex_lock(&cpm->i2c_mutex);
> +
> + /* Reset to use first buffer */
> + out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase));
> + out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase));
> +
> + tbdf = cpm->tbase;
> + rbdf = cpm->rbase;
> +
> + tptr = 0;
> + rptr = 0;
> +
> + while (tptr < num) {
> + pmsg = &msgs[tptr];
> + dev_dbg(&adap->dev, "R: %d T: %d\n", rptr, tptr);
> +
> + cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr);
> + if (pmsg->flags & I2C_M_RD)
> + rptr++;
> + tptr++;
> + }
> + /* Start transfer now */
> + /* Chip bug, set enable here */
> + out_8(&i2c_reg->i2cmr, 0x13); /* Enable RX/TX/Error interupts */
Hardcoded value. Some OR-ed defines should be more readable.
> + out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */
> + setbits8(&i2c_reg->i2mod, 1); /* Enable */
Hardcoded value.
> + /* Begin transmission */
> + setbits8(&i2c_reg->i2com, 0x80);
Hardcoded value. (I also wonder if 0x81 might be more suitable, as it
keeps the "be-a-master"-bit set. Still, both values work with my setup.)
> +
> + tptr = 0;
> + rptr = 0;
> +
> + while (tptr < num) {
> + /* Check for outstanding messages */
> + dev_dbg(&adap->dev, "test ready.\n");
> + pmsg = &msgs[tptr];
> + if (pmsg->flags & I2C_M_RD)
> + ret = wait_event_interruptible_timeout(cpm->i2c_wait,
> + !(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY),
> + 1 * HZ);
> + else
> + ret = wait_event_interruptible_timeout(cpm->i2c_wait,
> + !(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_READY),
> + 1 * HZ);
> + if (ret == 0) {
> + ret = -EREMOTEIO;
> + dev_dbg(&adap->dev, "I2C read: timeout!\n");
> + goto out_err;
> + }
> + if (ret > 0) {
> + dev_dbg(&adap->dev, "ready.\n");
> + ret = cpm_i2c_check_message(adap, pmsg, tptr, rptr);
> + tptr++;
> + if (pmsg->flags & I2C_M_RD)
> + rptr++;
> + if (ret)
> + goto out_err;
> + }
> + }
> +#ifdef I2C_CHIP_ERRATA
> + /*
> + * Chip errata, clear enable. This is not needed on rev D4 CPUs.
> + * Disabling I2C too early may cause too short stop condition
> + */
> + udelay(4);
> + clrbits8(&i2c_reg->i2mod, 1);
I was unable to find the corresponding errata document, still I wonder
if it is a 0 which should have been written? The text says "clear" and
according to the reference manual, this means the bit should be 0.
> +#endif
> + mutex_unlock(&cpm->i2c_mutex);
> + return (num);
> +
> +out_err:
> + cpm_i2c_force_close(adap);
> +#ifdef I2C_CHIP_ERRATA
> + /*
> + * Chip errata, clear enable. This is not needed on rev D4 CPUs.
> + */
> + clrbits8(&i2c_reg->i2mod, 1);
write 0? see above.
> +#endif
> + mutex_unlock(&cpm->i2c_mutex);
> + return ret;
> +}
> +
> +static u32 cpm_i2c_func(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
> +}
> +
> +/* -----exported algorithm data: ------------------------------------- */
> +
> +static const struct i2c_algorithm cpm_i2c_algo = {
> + .master_xfer = cpm_i2c_xfer,
> + .functionality = cpm_i2c_func,
> +};
> +
> +static const struct i2c_adapter cpm_ops = {
> + .owner = THIS_MODULE,
> + .name = "i2c-cpm",
> + .algo = &cpm_i2c_algo,
> + .class = I2C_CLASS_HWMON,
> +};
> +
> +static int __devinit cpm_i2c_setup(struct cpm_i2c *cpm)
> +{
> + struct of_device *ofdev = cpm->ofdev;
> + const u32 *data;
> + int len, ret, i;
> + void __iomem *i2c_base;
> + cbd_t __iomem *tbdf;
> + cbd_t __iomem *rbdf;
> + unsigned char brg;
> +
> + dev_dbg(&cpm->ofdev->dev, "cpm_i2c_setup()\n");
> +
> + init_waitqueue_head(&cpm->i2c_wait);
> + mutex_init(&cpm->i2c_mutex);
> +
> + cpm->irq = of_irq_to_resource(ofdev->node, 0, NULL);
> + if (cpm->irq == NO_IRQ)
> + return -EINVAL;
> +
> + /* Install interrupt handler. */
> + ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c",
> + &cpm->adap);
> + if (ret)
> + goto out_irq;
> +
> + /* IIC parameter RAM */
> + i2c_base = of_iomap(ofdev->node, 1);
> + if (i2c_base == NULL) {
> + ret = -EINVAL;
> + goto out_irq;
> + }
> +
> + if (of_device_is_compatible(ofdev->node, "fsl,cpm1-i2c")) {
> +
> + /* Check for and use a microcode relocation patch. */
> + cpm->i2c_ram = i2c_base;
> + cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase);
> +
> + /*
> + * Maybe should use cpm_muram_alloc instead of hardcoding
> + * this in micropatch.c
> + */
> + if (cpm->i2c_addr) {
> + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
> + iounmap(i2c_base);
> + }
> +
> + cpm->version = 1;
> +
> + } else if (of_device_is_compatible(ofdev->node, "fsl,cpm2-i2c")) {
> + cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64);
> + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr);
> + out_be16(i2c_base, cpm->i2c_addr);
> + iounmap(i2c_base);
> +
> + cpm->version = 2;
> +
> + } else {
> + iounmap(i2c_base);
> + ret = -EINVAL;
> + goto out_irq;
> + }
> +
> + /* I2C control/status registers */
> + cpm->i2c_reg = of_iomap(ofdev->node, 0);
> + if (cpm->i2c_reg == NULL) {
> + ret = -EINVAL;
> + goto out_ram;
> + }
> +
> + data = of_get_property(ofdev->node, "fsl,cpm-command", &len);
> + if (!data || len != 4) {
> + ret = -EINVAL;
> + goto out_reg;
> + }
> + cpm->cp_command = *data;
> +
> + data = of_get_property(ofdev->node, "linux,i2c-class", &len);
> + if (data && len == 4)
> + cpm->adap.class = *data;
> +
> + /*
> + * Allocate space for CPM_MAXBD transmit and receive buffer
> + * descriptors in the DP ram.
> + */
> + cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8);
> + if (!cpm->dp_addr) {
> + ret = -ENOMEM;
> + goto out_reg;
> + }
> +
> + cpm->tbase = cpm_muram_addr(cpm->dp_addr);
> + cpm->rbase = cpm_muram_addr(cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD);
> +
> + /* Allocate TX and RX buffers */
> +
> + tbdf = cpm->tbase;
> + rbdf = cpm->rbase;
> +
> + for (i = 0; i < CPM_MAXBD; i++) {
> + cpm->rxbuf[i] = dma_alloc_coherent(
> + NULL, CPM_MAX_READ + 1, &cpm->rxdma[i], GFP_KERNEL);
> + if (!cpm->rxbuf[i]) {
> + ret = -ENOMEM;
> + goto out_muram;
> + }
> + out_be32(&rbdf[i].cbd_bufaddr, ((cpm->rxdma[i] + 1) & ~1));
> +
> + cpm->txbuf[i] = (unsigned char *)dma_alloc_coherent(
> + NULL, CPM_MAX_READ + 1, &cpm->txdma[i], GFP_KERNEL);
> + if (!cpm->txbuf[i]) {
> + ret = -ENOMEM;
> + goto out_muram;
> + }
> + out_be32(&tbdf[i].cbd_bufaddr, cpm->txdma[i]);
> + }
> +
> + /* Initialize Tx/Rx parameters. */
> +
> + cpm_reset_i2c_params(cpm);
> +
> + dev_dbg(&cpm->ofdev->dev, "i2c_ram %p, i2c_addr 0x%04x\n",
> + cpm->i2c_ram, cpm->i2c_addr);
> + dev_dbg(&cpm->ofdev->dev, "tbase 0x%04x, rbase 0x%04x\n",
> + (u8 __iomem *)cpm->tbase - DPRAM_BASE,
> + (u8 __iomem *)cpm->rbase - DPRAM_BASE);
> +
> + cpm_command(cpm->cp_command, CPM_CR_INIT_TRX);
> +
> + /*
> + * Select an invalid address. Just make sure we don't use loopback mode
> + */
> + out_8(&cpm->i2c_reg->i2add, 0xfe);
Maybe 0x7f << 1 is a tiny bit more obvious?
> +
> + /* Make clock run at 60 kHz. */
> +
> + brg = get_brgfreq() / (32 * 2 * 60000) - 3;
> + out_8(&cpm->i2c_reg->i2brg, brg);
> +
> + out_8(&cpm->i2c_reg->i2mod, 0x00);
> + out_8(&cpm->i2c_reg->i2com, 0x01); /* Master mode */
Hardcoded value.
> +
> + /* Disable interrupts. */
> + out_8(&cpm->i2c_reg->i2cmr, 0);
> + out_8(&cpm->i2c_reg->i2cer, 0xff);
> +
> + return 0;
> +
> +out_muram:
> + for (i = 0; i < CPM_MAXBD; i++) {
> + if (cpm->rxbuf[i])
> + dma_free_coherent(NULL, CPM_MAX_READ + 1,
> + cpm->rxbuf[i], cpm->rxdma[i]);
> + if (cpm->txbuf[i])
> + dma_free_coherent(NULL, CPM_MAX_READ + 1,
> + cpm->txbuf[i], cpm->txdma[i]);
> + }
> + cpm_muram_free(cpm->dp_addr);
> +out_reg:
> + iounmap(cpm->i2c_reg);
> +out_ram:
> + if ((cpm->version == 1) && (!cpm->i2c_addr))
> + iounmap(cpm->i2c_ram);
> + if (cpm->version == 2)
> + cpm_muram_free(cpm->i2c_addr);
> +out_irq:
> + free_irq(cpm->irq, &cpm->adap);
> + return ret;
> +}
> +
> +static void cpm_i2c_shutdown(struct cpm_i2c *cpm)
> +{
> + int i;
> +
> + /* Shut down I2C. */
> + clrbits8(&cpm->i2c_reg->i2mod, 1);
write 0? see above.
> +
> + /* Disable interrupts */
> + out_8(&cpm->i2c_reg->i2cmr, 0);
> + out_8(&cpm->i2c_reg->i2cer, 0xff);
> +
> + free_irq(cpm->irq, &cpm->adap);
> +
> + /* Free all memory */
> + for (i = 0; i < CPM_MAXBD; i++) {
> + dma_free_coherent(NULL, CPM_MAX_READ + 1,
> + cpm->rxbuf[i], cpm->rxdma[i]);
> + dma_free_coherent(NULL, CPM_MAX_READ + 1,
> + cpm->txbuf[i], cpm->txdma[i]);
> + }
> +
> + cpm_muram_free(cpm->dp_addr);
> + iounmap(cpm->i2c_reg);
> +
> + if ((cpm->version == 1) && (!cpm->i2c_addr))
> + iounmap(cpm->i2c_ram);
> + if (cpm->version == 2)
> + cpm_muram_free(cpm->i2c_addr);
> +
> + return;
> +}
> +
> +static int __devinit cpm_i2c_probe(struct of_device *ofdev,
> + const struct of_device_id *match)
> +{
> + int result;
> + struct cpm_i2c *cpm;
> +
> + cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL);
> + if (!cpm)
> + return -ENOMEM;
> +
> + cpm->ofdev = ofdev;
> +
> + dev_set_drvdata(&ofdev->dev, cpm);
> +
> + cpm->adap = cpm_ops;
> + i2c_set_adapdata(&cpm->adap, cpm);
> + cpm->adap.dev.parent = &ofdev->dev;
> +
> + result = cpm_i2c_setup(cpm);
> + if (result) {
> + dev_err(&ofdev->dev, "Unable to init hardware\n");
> + goto out_free;
> + }
> +
> + /* register new adapter to i2c module... */
> +
> + result = i2c_add_adapter(&cpm->adap);
> + if (result < 0) {
> + dev_err(&ofdev->dev, "Unable to register with I2C\n");
> + goto out_shut;
> + }
> +
> + dev_dbg(&ofdev->dev, "hw routines for %s registered.\n",
> + cpm->adap.name);
> +
> + /*
> + * register OF I2C devices
> + */
> + of_register_i2c_devices(&cpm->adap, ofdev->node);
> +
> + return 0;
> +out_shut:
> + cpm_i2c_shutdown(cpm);
> +out_free:
> + dev_set_drvdata(&ofdev->dev, NULL);
> + kfree(cpm);
> +
> + return result;
> +}
> +
> +static int __devexit cpm_i2c_remove(struct of_device *ofdev)
> +{
> + struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev);
> +
> + i2c_del_adapter(&cpm->adap);
> +
> + cpm_i2c_shutdown(cpm);
> +
> + dev_set_drvdata(&ofdev->dev, NULL);
> + kfree(cpm);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id cpm_i2c_match[] = {
> + {
> + .compatible = "fsl,cpm-i2c",
> + },
> + {},
> +};
> +
> +MODULE_DEVICE_TABLE(of, cpm_i2c_match);
> +
> +static struct of_platform_driver cpm_i2c_driver = {
> + .match_table = cpm_i2c_match,
> + .probe = cpm_i2c_probe,
> + .remove = __devexit_p(cpm_i2c_remove),
> + .driver = {
> + .name = "fsl-i2c-cpm",
> + .owner = THIS_MODULE,
> + }
> +};
> +
> +static int __init cpm_i2c_init(void)
> +{
> + return of_register_platform_driver(&cpm_i2c_driver);
> +}
> +
> +static void __exit cpm_i2c_exit(void)
> +{
> + of_unregister_platform_driver(&cpm_i2c_driver);
> +}
> +
> +module_init(cpm_i2c_init);
> +module_exit(cpm_i2c_exit);
> +
> +MODULE_AUTHOR("Jochen Friedrich <jochen at scram.de>");
> +MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards");
> +MODULE_LICENSE("GPL");
> --
> 1.5.4.5
>
>
>
>
> _______________________________________________
> i2c mailing list
> i2c at lm-sensors.org
> http://lists.lm-sensors.org/mailman/listinfo/i2c
In general, the driver works well for me (just had to disable broadcast
responses; eeprom at 00-1f \o/).
Kind regards,
Wolfram
--
Dipl.-Ing. Wolfram Sang | http://www.pengutronix.de
Pengutronix - Linux Solutions for Science and Industry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: Digital signature
URL: <http://lists.ozlabs.org/pipermail/linuxppc-dev/attachments/20080506/50c17e0f/attachment.pgp>
More information about the Linuxppc-dev
mailing list