[POWERPC] mpc52xx: Amalgamated dts fixes and updates
Anatolij Gustschin
agust at denx.de
Sat Mar 22 11:41:00 EST 2008
Bartlomiej Sieka wrote:
> The bulk of this patch is taken from
> http://patchwork.ozlabs.org/linuxppc/patch?q=Balakowicz&id=16197, with few
> other updates, in particluar one posted by Anatolij Gustschin, which fixes
> an Oops during boot.
>
> Signed-off-by: Marian Balakowicz <m8 at semihalf.com>
> ---
> Anatolij, would you like to add your S-O-B?
Signed-off-by: Anatolij Gustschin <agust at denx.de>
>
> diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
> index 30737ea..8b2e8e4 100644
> --- a/arch/powerpc/boot/dts/cm5200.dts
> +++ b/arch/powerpc/boot/dts/cm5200.dts
> @@ -159,6 +159,7 @@
> };
>
> dma-controller at 1200 {
> + device_type = "dma-controller";
> compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
> reg = <1200 80>;
> interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
> @@ -212,13 +213,31 @@
> ethernet at 3000 {
> device_type = "network";
> compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
> - reg = <3000 800>;
> + reg = <3000 400>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <2 5 0>;
> interrupt-parent = <&mpc5200_pic>;
> + phy-handle = <&phy0>;
> + };
> +
> + mdio at 3000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + device_type = "mdio";
> + compatible = "fsl,mpc5200b-mdio";
> + reg = <3000 400>; // fec range, since we need to setup fec interrupts
> + interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
> + interrupt-parent = <&mpc5200_pic>;
> +
> + phy0:ethernet-phy at 0 {
> + device_type = "ethernet-phy";
> + reg = <0>;
> + };
> };
>
> i2c at 3d40 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
> reg = <3d40 40>;
> interrupts = <2 10 0>;
> @@ -231,4 +250,22 @@
> reg = <8000 4000>;
> };
> };
> +
> + lpb {
> + model = "fsl,lpb";
> + compatible = "fsl,lpb";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <0 0 fc000000 2000000>;
> +
> + // 16-bit flash device at LocalPlus Bus CS0
> + flash at 0,0 {
> + compatible = "cfi-flash";
> + reg = <0 0 2000000>;
> + bank-width = <2>;
> + device-width = <2>;
> + #size-cells = <1>;
> + #address-cells = <1>;
> + };
> + };
> };
> diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
> index 76951ab..9ca81ff 100644
> --- a/arch/powerpc/boot/dts/motionpro.dts
> +++ b/arch/powerpc/boot/dts/motionpro.dts
> @@ -127,6 +127,13 @@
> interrupt-parent = <&mpc5200_pic>;
> };
>
> + mscan at 900 {
> + compatible = "mpc5200b-mscan\0mpc5200-mscan";
> + interrupts = <2 11 0>;
> + interrupt-parent = <&mpc5200_pic>;
> + reg = <900 80>;
> + };
> +
> mscan at 980 {
> compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
> interrupts = <2 12 0>;
> @@ -148,7 +155,6 @@
> interrupt-parent = <&mpc5200_pic>;
> };
>
> -
> spi at f00 {
> compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
> reg = <f00 20>;
> @@ -164,6 +170,7 @@
> };
>
> dma-controller at 1200 {
> + device_type = "dma-controller";
> compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
> reg = <1200 80>;
> interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
> @@ -209,10 +216,26 @@
> ethernet at 3000 {
> device_type = "network";
> compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
> - reg = <3000 800>;
> + reg = <3000 400>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <2 5 0>;
> interrupt-parent = <&mpc5200_pic>;
> + phy-handle = <&phy0>;
> + };
> +
> + mdio at 3000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + device_type = "mdio";
> + compatible = "fsl,mpc5200b-mdio";
> + reg = <3000 400>; // fec range, since we need to setup fec interrupts
> + interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
> + interrupt-parent = <&mpc5200_pic>;
> +
> + phy0:ethernet-phy at 0 {
> + device_type = "ethernet-phy";
> + reg = <2>;
> + };
> };
>
> ata at 3a00 {
> @@ -223,11 +246,19 @@
> };
>
> i2c at 3d40 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
> reg = <3d40 40>;
> interrupts = <2 10 0>;
> interrupt-parent = <&mpc5200_pic>;
> fsl5200-clocking;
> +
> + rtc at 68 {
> + device_type = "rtc";
> + compatible = "dallas,ds1339";
> + reg = <68>;
> + };
> };
>
> sram at 8000 {
> @@ -240,7 +271,8 @@
> compatible = "fsl,lpb";
> #address-cells = <2>;
> #size-cells = <1>;
> - ranges = <1 0 50000000 00010000
> + ranges = <0 0 ff000000 01000000
> + 1 0 50000000 00010000
> 2 0 50010000 00010000
> 3 0 50020000 00010000>;
>
> @@ -271,31 +303,15 @@
> compatible = "promess,pro_module_dio";
> reg = <3 800 2>;
> };
> - };
>
> - pci at f0000d00 {
> - #interrupt-cells = <1>;
> - #size-cells = <2>;
> - #address-cells = <3>;
> - device_type = "pci";
> - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
> - reg = <f0000d00 100>;
> - interrupt-map-mask = <f800 0 0 7>;
> - interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
> - c000 0 0 2 &mpc5200_pic 1 1 3
> - c000 0 0 3 &mpc5200_pic 1 2 3
> - c000 0 0 4 &mpc5200_pic 1 3 3
> -
> - c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
> - c800 0 0 2 &mpc5200_pic 1 2 3
> - c800 0 0 3 &mpc5200_pic 1 3 3
> - c800 0 0 4 &mpc5200_pic 0 0 3>;
> - clock-frequency = <0>; // From boot loader
> - interrupts = <2 8 0 2 9 0 2 a 0>;
> - interrupt-parent = <&mpc5200_pic>;
> - bus-range = <0 0>;
> - ranges = <42000000 0 80000000 80000000 0 20000000
> - 02000000 0 a0000000 a0000000 0 10000000
> - 01000000 0 00000000 b0000000 0 01000000>;
> + // 16-bit flash device at LocalPlus Bus CS0
> + flash at 0,0 {
> + compatible = "cfi-flash";
> + reg = <0 0 01000000>;
> + bank-width = <2>;
> + device-width = <2>;
> + #size-cells = <1>;
> + #address-cells = <1>;
> + };
> };
> };
> diff --git a/arch/powerpc/boot/dts/tqm5200.dts b/arch/powerpc/boot/dts/tqm5200.dts
> index c86464f..bbac984 100644
> --- a/arch/powerpc/boot/dts/tqm5200.dts
> +++ b/arch/powerpc/boot/dts/tqm5200.dts
> @@ -83,6 +83,7 @@
> };
>
> dma-controller at 1200 {
> + device_type = "dma-controller";
> compatible = "fsl,mpc5200-bestcomm";
> reg = <1200 80>;
> interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
> @@ -127,10 +128,26 @@
> ethernet at 3000 {
> device_type = "network";
> compatible = "fsl,mpc5200-fec";
> - reg = <3000 800>;
> + reg = <3000 400>;
> local-mac-address = [ 00 00 00 00 00 00 ];
> interrupts = <2 5 0>;
> interrupt-parent = <&mpc5200_pic>;
> + phy-handle = <&phy0>;
> + };
> +
> + mdio at 3000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + device_type = "mdio";
> + compatible = "fsl,mpc5200b-mdio";
> + reg = <3000 400>; // fec range, since we need to setup fec interrupts
> + interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
> + interrupt-parent = <&mpc5200_pic>;
> +
> + phy0:ethernet-phy at 0 {
> + device_type = "ethernet-phy";
> + reg = <0>;
> + };
> };
>
> ata at 3a00 {
> @@ -141,11 +158,19 @@
> };
>
> i2c at 3d40 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> compatible = "fsl,mpc5200-i2c","fsl-i2c";
> reg = <3d40 40>;
> interrupts = <2 10 0>;
> interrupt-parent = <&mpc5200_pic>;
> fsl5200-clocking;
> +
> + rtc at 68 {
> + device_type = "rtc";
> + compatible = "dallas,ds1307";
> + reg = <68>;
> + };
> };
>
> sram at 8000 {
> @@ -154,6 +179,23 @@
> };
> };
>
> + lpb {
> + model = "fsl,lpb";
> + compatible = "fsl,lpb";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <0 0 fc000000 02000000>;
> +
> + flash at 0,0 {
> + compatible = "cfi-flash";
> + reg = <0 0 02000000>;
> + bank-width = <4>;
> + device-width = <2>;
> + #size-cells = <1>;
> + #address-cells = <1>;
> + };
> + };
> +
> pci at f0000d00 {
> #interrupt-cells = <1>;
> #size-cells = <2>;
>
>
More information about the Linuxppc-dev
mailing list