[RFC] 4xx hardware watchpoint support
Luis Machado
luisgpm at linux.vnet.ibm.com
Wed Jul 23 11:47:58 EST 2008
Hi,
> That, or adding a small function to move the bits to the appropriate
> registers (set_dbcr or set_dac_events).
>
> > Do you think it's worth to support this facility on 405's processors? If
> > so, i'll gladly work on a solution to it.
>
> I would think so. There's really no difference from a userspace
> perspective, so gdb watchpoints could be valuable there too. I'll
> leave it up to you though.
As the 440 support is ready and the 405 needs additional tweaking due to
the use of DBCR1 instead of DBCR0 and due to a different position scheme
of the DAC1R/DAC1W flags inside DBCR1, i'd say we should include this
code and handle the 405 case later.
We might have to handle it anyway if we're going to pursue the hardware
breakpoint interface work in the future.
I've fixed some formatting problems. Tested on a 440 Taishan board and
on a PPC970. Both worked as they should. Ok?
Signed-off-by: Luis Machado <luisgpm at br.ibm.com>
Index: linux-2.6.26/arch/powerpc/kernel/process.c
===================================================================
--- linux-2.6.26.orig/arch/powerpc/kernel/process.c 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/kernel/process.c 2008-07-22 16:46:36.000000000 -0700
@@ -47,6 +47,8 @@
#ifdef CONFIG_PPC64
#include <asm/firmware.h>
#endif
+#include <linux/kprobes.h>
+#include <linux/kdebug.h>
extern unsigned long _get_SP(void);
@@ -239,6 +241,36 @@
}
#endif /* CONFIG_SMP */
+void do_dabr(struct pt_regs *regs, unsigned long address,
+ unsigned long error_code)
+{
+ siginfo_t info;
+
+#if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE))
+ if (notify_die(DIE_DABR_MATCH, "dabr_match", regs, error_code,
+ 11, SIGSEGV) == NOTIFY_STOP)
+ return;
+
+ if (debugger_dabr_match(regs))
+ return;
+
+ /* Clear the DAC and struct entries. One shot trigger. */
+#else /* (defined(CONFIG_4xx) || defined(CONFIG_BOOKE)) */
+ mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~(DBSR_DAC1R | DBSR_DAC1W
+ | DBCR0_IDM));
+#endif
+
+ /* Clear the DABR */
+ set_dabr(0);
+
+ /* Deliver the signal to userspace */
+ info.si_signo = SIGTRAP;
+ info.si_errno = 0;
+ info.si_code = TRAP_HWBKPT;
+ info.si_addr = (void __user *)address;
+ force_sig_info(SIGTRAP, &info, current);
+}
+
static DEFINE_PER_CPU(unsigned long, current_dabr);
int set_dabr(unsigned long dabr)
@@ -254,6 +286,11 @@
#if defined(CONFIG_PPC64) || defined(CONFIG_6xx)
mtspr(SPRN_DABR, dabr);
#endif
+
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+ mtspr(SPRN_DAC1, dabr);
+#endif
+
return 0;
}
@@ -337,6 +374,12 @@
if (unlikely(__get_cpu_var(current_dabr) != new->thread.dabr))
set_dabr(new->thread.dabr);
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+ /* If new thread DAC (HW breakpoint) is the same then leave it. */
+ if (new->thread.dabr)
+ set_dabr(new->thread.dabr);
+#endif
+
new_thread = &new->thread;
old_thread = ¤t->thread;
@@ -525,6 +568,10 @@
if (current->thread.dabr) {
current->thread.dabr = 0;
set_dabr(0);
+
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+ current->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W);
+#endif
}
}
Index: linux-2.6.26/arch/powerpc/kernel/ptrace.c
===================================================================
--- linux-2.6.26.orig/arch/powerpc/kernel/ptrace.c 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/kernel/ptrace.c 2008-07-22 16:41:24.000000000 -0700
@@ -703,7 +703,7 @@
if (regs != NULL) {
#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
- task->thread.dbcr0 = DBCR0_IDM | DBCR0_IC;
+ task->thread.dbcr0 |= DBCR0_IDM | DBCR0_IC;
regs->msr |= MSR_DE;
#else
regs->msr |= MSR_SE;
@@ -716,9 +716,16 @@
{
struct pt_regs *regs = task->thread.regs;
+
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+ /* If DAC then do not single step, skip. */
+ if (task->thread.dabr)
+ return;
+#endif
+
if (regs != NULL) {
#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
- task->thread.dbcr0 = 0;
+ task->thread.dbcr0 &= ~(DBCR0_IC | DBCR0_IDM);
regs->msr &= ~MSR_DE;
#else
regs->msr &= ~MSR_SE;
@@ -727,22 +734,71 @@
clear_tsk_thread_flag(task, TIF_SINGLESTEP);
}
-static int ptrace_set_debugreg(struct task_struct *task, unsigned long addr,
+int ptrace_set_debugreg(struct task_struct *task, unsigned long addr,
unsigned long data)
{
- /* We only support one DABR and no IABRS at the moment */
+ /* For ppc64 we support one DABR and no IABR's at the moment (ppc64).
+ For embedded processors we support one DAC and no IAC's
+ at the moment. */
if (addr > 0)
return -EINVAL;
- /* The bottom 3 bits are flags */
if ((data & ~0x7UL) >= TASK_SIZE)
return -EIO;
- /* Ensure translation is on */
+#ifdef CONFIG_PPC64
+
+ /* For processors using DABR (i.e. 970), the bottom 3 bits are flags.
+ It was assumed, on previous implementations, that 3 bits were
+ passed together with the data address, fitting the design of the
+ DABR register, as follows:
+
+ bit 0: Read flag
+ bit 1: Write flag
+ bit 2: Breakpoint translation
+
+ Thus, we use them here as so. */
+
+ /* Ensure breakpoint translation bit is set. */
if (data && !(data & DABR_TRANSLATION))
return -EIO;
+ /* Move contents to the DABR register. */
task->thread.dabr = data;
+
+#endif
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+
+ /* As described above, it was assumed 3 bits were passed with the data
+ address, but we will assume only the mode bits will be passed
+ as to not cause alignment restrictions for DAC-based processors. */
+ /* DAC's hold the whole address without any mode flags. */
+ task->thread.dabr = data & ~0x3UL;
+
+ if (task->thread.dabr == 0) {
+ task->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W | DBCR0_IDM);
+ task->thread.regs->msr &= ~MSR_DE;
+ return 0;
+ }
+
+ /* Read or Write bits must be set. */
+
+ if (!(data & 0x3UL))
+ return -EINVAL;
+
+ /* Set the Internal Debugging flag (IDM bit 1) for the DBCR0
+ register. */
+ task->thread.dbcr0 = DBCR0_IDM;
+
+ /* Check for write and read flags and set DBCR0
+ accordingly. */
+ if (data & 0x1UL)
+ task->thread.dbcr0 |= DBSR_DAC1R;
+ if (data & 0x2UL)
+ task->thread.dbcr0 |= DBSR_DAC1W;
+
+ task->thread.regs->msr |= MSR_DE;
+#endif
return 0;
}
Index: linux-2.6.26/arch/powerpc/kernel/signal.c
===================================================================
--- linux-2.6.26.orig/arch/powerpc/kernel/signal.c 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/kernel/signal.c 2008-07-22 16:47:22.000000000 -0700
@@ -145,8 +145,12 @@
* user space. The DABR will have been cleared if it
* triggered inside the kernel.
*/
- if (current->thread.dabr)
+ if (current->thread.dabr) {
set_dabr(current->thread.dabr);
+#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
+ mtspr(SPRN_DBCR0, current->thread.dbcr0);
+#endif
+ }
if (is32) {
if (ka.sa.sa_flags & SA_SIGINFO)
Index: linux-2.6.26/arch/powerpc/kernel/traps.c
===================================================================
--- linux-2.6.26.orig/arch/powerpc/kernel/traps.c 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/kernel/traps.c 2008-07-22 16:49:28.000000000 -0700
@@ -1067,6 +1067,22 @@
}
_exception(SIGTRAP, regs, TRAP_TRACE, regs->nip);
+ } else if (debug_status & (DBSR_DAC1R | DBSR_DAC1W)) {
+ regs->msr &= ~MSR_DE;
+
+ if (user_mode(regs)) {
+ current->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W |
+ DBCR0_IDM);
+ } else {
+ /* Disable DAC interupts. */
+ mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~(DBSR_DAC1R |
+ DBSR_DAC1W | DBCR0_IDM));
+
+ /* Clear the DAC event. */
+ mtspr(SPRN_DBSR, (DBSR_DAC1R | DBSR_DAC1W));
+ }
+ /* Setup and send the trap to the handler. */
+ do_dabr(regs, mfspr(SPRN_DAC1), debug_status);
}
}
#endif /* CONFIG_4xx || CONFIG_BOOKE */
Index: linux-2.6.26/arch/powerpc/kernel/entry_32.S
===================================================================
--- linux-2.6.26.orig/arch/powerpc/kernel/entry_32.S 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/kernel/entry_32.S 2008-07-20 16:58:54.000000000 -0700
@@ -148,7 +148,7 @@
/* Check to see if the dbcr0 register is set up to debug. Use the
internal debug mode bit to do this. */
lwz r12,THREAD_DBCR0(r12)
- andis. r12,r12,DBCR0_IDM at h
+ andis. r12,r12,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h
beq+ 3f
/* From user and task is ptraced - load up global dbcr0 */
li r12,-1 /* clear all pending debug events */
@@ -292,7 +292,7 @@
/* If the process has its own DBCR0 value, load it up. The internal
debug mode bit tells us that dbcr0 should be loaded. */
lwz r0,THREAD+THREAD_DBCR0(r2)
- andis. r10,r0,DBCR0_IDM at h
+ andis. r10,r0,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h
bnel- load_dbcr0
#endif
#ifdef CONFIG_44x
@@ -720,7 +720,7 @@
/* Check whether this process has its own DBCR0 value. The internal
debug mode bit tells us that dbcr0 should be loaded. */
lwz r0,THREAD+THREAD_DBCR0(r2)
- andis. r10,r0,DBCR0_IDM at h
+ andis. r10,r0,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h
bnel- load_dbcr0
#endif
Index: linux-2.6.26/arch/powerpc/mm/fault.c
===================================================================
--- linux-2.6.26.orig/arch/powerpc/mm/fault.c 2008-07-20 16:56:57.000000000 -0700
+++ linux-2.6.26/arch/powerpc/mm/fault.c 2008-07-20 16:58:54.000000000 -0700
@@ -100,31 +100,6 @@
return 0;
}
-#if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE))
-static void do_dabr(struct pt_regs *regs, unsigned long address,
- unsigned long error_code)
-{
- siginfo_t info;
-
- if (notify_die(DIE_DABR_MATCH, "dabr_match", regs, error_code,
- 11, SIGSEGV) == NOTIFY_STOP)
- return;
-
- if (debugger_dabr_match(regs))
- return;
-
- /* Clear the DABR */
- set_dabr(0);
-
- /* Deliver the signal to userspace */
- info.si_signo = SIGTRAP;
- info.si_errno = 0;
- info.si_code = TRAP_HWBKPT;
- info.si_addr = (void __user *)address;
- force_sig_info(SIGTRAP, &info, current);
-}
-#endif /* !(CONFIG_4xx || CONFIG_BOOKE)*/
-
/*
* For 600- and 800-family processors, the error_code parameter is DSISR
* for a data fault, SRR1 for an instruction fault. For 400-family processors
Index: linux-2.6.26/include/asm-powerpc/system.h
===================================================================
--- linux-2.6.26.orig/include/asm-powerpc/system.h 2008-07-20 16:57:09.000000000 -0700
+++ linux-2.6.26/include/asm-powerpc/system.h 2008-07-20 23:00:36.000000000 -0700
@@ -110,6 +110,8 @@
#endif
extern int set_dabr(unsigned long dabr);
+extern void do_dabr(struct pt_regs *regs, unsigned long address,
+ unsigned long error_code);
extern void print_backtrace(unsigned long *);
extern void show_regs(struct pt_regs * regs);
extern void flush_instruction_cache(void);
More information about the Linuxppc-dev
mailing list