[PATCH 3/5] powerpc/83xx: Add USB Host/Gadget support for MPC8360E-MDS boards
Anton Vorontsov
avorontsov at ru.mvista.com
Thu Dec 4 06:27:43 EST 2008
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli at freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
---
arch/powerpc/boot/dts/mpc836x_mds.dts | 43 ++++++++++++++++-
arch/powerpc/platforms/83xx/mpc836x_mds.c | 75 +++++++++++++++++++++++++++++
2 files changed, 116 insertions(+), 2 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index 14534d0..6e34f17 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -69,8 +69,18 @@
};
bcsr at 1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
compatible = "fsl,mpc8360mds-bcsr";
reg = <1 0 0x8000>;
+ ranges = <0 1 0 0x8000>;
+
+ bcsr13: gpio-controller at d {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360mds-bcsr-gpio";
+ reg = <0xd 1>;
+ gpio-controller;
+ };
};
};
@@ -195,10 +205,21 @@
};
par_io at 1400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
reg = <0x1400 0x100>;
+ ranges = <0 0x1400 0x100>;
device_type = "par_io";
num-ports = <7>;
+ qe_pio_b: gpio-controller at 18 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x18 0x18>;
+ gpio-controller;
+ };
+
pio1: ucc_pin at 01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
@@ -282,6 +303,15 @@
};
};
+ timer at 440 {
+ compatible = "fsl,mpc8360-qe-gtm",
+ "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ clock-frequency = <132000000>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ };
+
spi at 4c0 {
cell-index = <0>;
compatible = "fsl,spi";
@@ -301,11 +331,20 @@
};
usb at 6c0 {
- compatible = "qe_udc";
+ compatible = "fsl,mpc8360-qe-usb",
+ "fsl,mpc8323-qe-usb";
reg = <0x6c0 0x40 0x8b00 0x100>;
interrupts = <11>;
interrupt-parent = <&qeic>;
- mode = "slave";
+ fsl,fullspeed-clock = "clk21";
+ fsl,lowspeed-clock = "brg9";
+ gpios = <&qe_pio_b 2 0 /* USBOE */
+ &qe_pio_b 3 0 /* USBTP */
+ &qe_pio_b 8 0 /* USBTN */
+ &qe_pio_b 9 0 /* USBRP */
+ &qe_pio_b 11 0 /* USBRN */
+ &bcsr13 5 0 /* SPEED */
+ &bcsr13 4 1>; /* POWER */
};
enet0: ucc at 2000 {
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 9d46e5b..fbcca19 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -43,6 +43,7 @@
#include <asm/udbg.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
+#include <sysdev/simple_gpio.h>
#include <asm/qe.h>
#include <asm/qe_ic.h>
@@ -93,6 +94,16 @@ static void __init mpc836x_mds_setup_arch(void)
for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;)
par_io_of_config(np);
+#ifdef CONFIG_QE_USB
+ /* Must fixup Par IO before QE GPIO chips are registered. */
+ par_io_config_pin(1, 2, 1, 0, 3, 0); /* USBOE */
+ par_io_config_pin(1, 3, 1, 0, 3, 0); /* USBTP */
+ par_io_config_pin(1, 8, 1, 0, 1, 0); /* USBTN */
+ par_io_config_pin(1, 10, 2, 0, 3, 0); /* USBRXD */
+ par_io_config_pin(1, 9, 2, 1, 3, 0); /* USBRP */
+ par_io_config_pin(1, 11, 2, 1, 3, 0); /* USBRN */
+ par_io_config_pin(2, 20, 2, 0, 1, 0); /* CLK21 */
+#endif /* CONFIG_QE_USB */
}
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
@@ -151,6 +162,70 @@ static int __init mpc836x_declare_of_platform_devices(void)
}
machine_device_initcall(mpc836x_mds, mpc836x_declare_of_platform_devices);
+#ifdef CONFIG_QE_USB
+static int __init mpc836x_usb_cfg(void)
+{
+ u8 __iomem *bcsr;
+ struct device_node *np;
+ const char *mode;
+ int ret = 0;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc8360mds-bcsr");
+ if (!np)
+ return -ENODEV;
+
+ bcsr = of_iomap(np, 0);
+ of_node_put(np);
+ if (!bcsr)
+ return -ENOMEM;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,mpc8323-qe-usb");
+ if (!np) {
+ ret = -ENODEV;
+ goto err;
+ }
+
+#define BCSR8_TSEC1M_MASK (0x3 << 6)
+#define BCSR8_TSEC1M_RGMII (0x0 << 6)
+#define BCSR8_TSEC2M_MASK (0x3 << 4)
+#define BCSR8_TSEC2M_RGMII (0x0 << 4)
+ /*
+ * Default is GMII (2), but we should set it to RGMII (0) if we use
+ * USB (Eth PHY is in RGMII mode anyway).
+ */
+ clrsetbits_8(&bcsr[8], BCSR8_TSEC1M_MASK | BCSR8_TSEC2M_MASK,
+ BCSR8_TSEC1M_RGMII | BCSR8_TSEC2M_RGMII);
+
+#define BCSR13_USBMASK 0x0f
+#define BCSR13_nUSBEN 0x08 /* 1 - Disable, 0 - Enable */
+#define BCSR13_USBSPEED 0x04 /* 1 - Full, 0 - Low */
+#define BCSR13_USBMODE 0x02 /* 1 - Host, 0 - Function */
+#define BCSR13_nUSBVCC 0x01 /* 1 - gets VBUS, 0 - supplies VBUS */
+
+ clrsetbits_8(&bcsr[13], BCSR13_USBMASK, BCSR13_USBSPEED);
+
+ mode = of_get_property(np, "mode", NULL);
+ if (mode && !strcmp(mode, "peripheral")) {
+ setbits8(&bcsr[13], BCSR13_nUSBVCC);
+ qe_usb_clock_set(QE_CLK21, 48000000);
+ } else {
+ setbits8(&bcsr[13], BCSR13_USBMODE);
+ /*
+ * The BCSR GPIOs are used to control power and
+ * speed of the USB transceiver. This is needed for
+ * the USB Host only.
+ */
+ simple_gpiochip_init("fsl,mpc8360mds-bcsr-gpio");
+ }
+
+ of_node_put(np);
+err:
+ iounmap(bcsr);
+ return ret;
+}
+machine_arch_initcall(mpc836x_mds, mpc836x_usb_cfg);
+#endif /* CONFIG_QE_USB */
+
static void __init mpc836x_mds_init_IRQ(void)
{
struct device_node *np;
--
1.5.6.5
More information about the Linuxppc-dev
mailing list