[PATCH 5/7] [POWERPC] mpc8568mds: update dts to be able to use UCCs

[Anton Vorontsov]

1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
   u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;

Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
---
 arch/powerpc/boot/dts/mpc8568mds.dts |   22 +++++++++++-----------
 1 files changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index c472a4b..1d082fb 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -95,10 +95,10 @@
 			device_type = "mdio";
 			compatible = "gianfar";
 			reg = <24520 20>;
-			phy0: ethernet-phy at 0 {
+			phy0: ethernet-phy at 7 {
 				interrupt-parent = <&mpic>;
 				interrupts = <1 1>;
-				reg = <0>;
+				reg = <7>;
 				device_type = "ethernet-phy";
 			};
 			phy1: ethernet-phy at 1 {
@@ -286,7 +286,7 @@
 					4  1a  2  0  2  0 	/* RxD7 */
 					4  0b  1  0  2  0 	/* TX_EN */
 					4  18  1  0  2  0 	/* TX_ER */
-					4  0f  2  0  2  0 	/* RX_DV */
+					4  10  2  0  2  0 	/* RX_DV */
 					4  1e  2  0  2  0 	/* RX_ER */
 					4  11  2  0  2  0 	/* RX_CLK */
 					4  13  1  0  2  0 	/* GTX_CLK */
@@ -377,10 +377,10 @@
 			mac-address = [ 00 00 00 00 00 00 ];
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			rx-clock = <0>;
-			tx-clock = <19>;
-			phy-handle = <&qe_phy0>;
-			phy-connection-type = "gmii";
+			tx-clock = <20>;
 			pio-handle = <&pio1>;
+			phy-handle = <&phy0>;
+			phy-connection-type = "rgmii-id";
 		};
 
 		ucc at 3000 {
@@ -399,10 +399,10 @@
 			mac-address = [ 00 00 00 00 00 00 ];
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			rx-clock = <0>;
-			tx-clock = <14>;
-			phy-handle = <&qe_phy1>;
-			phy-connection-type = "gmii";
+			tx-clock = <20>;
 			pio-handle = <&pio2>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
 		};
 
 		mdio at 2120 {
@@ -414,10 +414,10 @@
 
 			/* These are the same PHYs as on
 			 * gianfar's MDIO bus */
-			qe_phy0: ethernet-phy at 00 {
+			qe_phy0: ethernet-phy at 07 {
 				interrupt-parent = <&mpic>;
 				interrupts = <1 1>;
-				reg = <0>;
+				reg = <7>;
 				device_type = "ethernet-phy";
 			};
 			qe_phy1: ethernet-phy at 01 {
-- 
1.5.0.6